Extend your socket's reach.

Safely extend your reach in areas where you could accidentally come into contact with live circuits.

Reach a variety of spots with the confidence that your extension won’t disengage.

Bend these extensions to reach inconveniently located fasteners. These sets include multiple extension lengths, so you can find the right length to reach around obstructions.

Lock your socket into these extensions to prevent accidental disengagement.

Convert from one square drive size to another.

These adapters are insulated to protect against accidental contact with live electrical circuits. They are tested to 1,000 volts to meet IEC 60900.

Turn sockets with a bit screwdriver.

Attach your square-drive sockets to drills, powered screwdrivers, and other tools that accept a hex shank.

Convert your socket into a flex socket to access fasteners from an angle.

Fit these adapters between a wrench and socket to enable finger tightening.

A digital display shows how torque measurements change as you turn the wrench. Set the desired torque and angle—lights and an audible alarm indicate when target has been reached or exceeded.

Already set to a specific torque limit, these adapters audibly click and release when you reach that setting to prevent overtightening.

Attach one of these adapters to a ratcheting box wrench to convert it to a ratcheting socket wrench.

Attach to your socket for a longer reach.

Attach one of these extensions to your impact socket to turn fasteners in hard-to-reach spaces.

Also known as positive-locking extensions, these extensions hold sockets place with a ball that only retracts when you pull the collar down. Designed to prevent accidental detachment, they lock to your socket more securely than other extensions.

Convert from one square drive size to another.

Convert your impact socket into a flex socket to access fasteners from an angle.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

Convert your impact socket into a flex socket to access fasteners from an angle.

First developed for aerospace and automotive assembly processes, these extensions will stand up to your high-volume production and assembly lines.

Bend these extensions around obstructions to access hard-to-reach fasteners.

Convert from one square drive size to another.

Prevent overtightening that can damage fasteners. These adapters spring back slightly when the set torque is reached.

Switch out worn or damaged bits instead of replacing your entire bit socket.

These chargers are for use with most DeWalt batteries, except Univolt batteries.

Recharge batteries for Makita tools.

Use these chargers with Black & Decker batteries.

Charge up to eight batteries at once.

After the battery is fully charged, these chargers continuously provide a low-level charge to maintain the battery without overcharging.

Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.

The power switch to these outlet strips is on an extension cord, so you can control power even when the strips are in hard to reach places, such as under a desk.

Often used in offices and workstations, these outlet strips power multiple devices from a single wall outlet.

A filter through the middle isolates two pairs of outlets, so high voltage equipment plugged into one pair won’t affect the other pair.

With a rubber housing, these outlet strips withstand drops and other impact.

A combination of an outlet box, cord, and duct, these outlet strips minimize tripping hazards and protect the cord from damage.

Automatically power heating and cooling devices on and off when temperatures rise or drop.

No need for mounting hardware—these outlet strips have magnets on the back to stick to steel walls, cabinets, and other magnetic surfaces.

Mount these strips into standard 19” wide electronics racks, enclosures, and cabinets.

These curved outlet strips clamp onto a pole or table leg.

Power multiple devices with one extension cord.

Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.

In addition to an outlet on the end, these cords have multiple inline outlets.

A locking lever on the socket keeps multiple devices connected to these extension cords.

If your Morse taper arbor is too small or large for your machine spindle, insert it into one of these adapters. Also known as sleeves or shell sockets.