Also known as machinery eyebolts.

Unlike conventional eyebolts, you can rotate the eye 360° to match the angle of your load.

Route wire and cable through the smooth eye without snagging.

Also known as nut eyebolts, these are designed for through-hole applications.

Also known as screw eyes, use the sharp point of these eyebolts to mount directly into wood.

Designed for angular lifting, hoist rings resist stresses that would bend or break an eyebolt. They have a lifting ring that pivots 180° front to back to compensate for roll and sway when lifting heavy or unbalanced loads.

Remove the shackle after lifting while keeping the base installed for future use.

These rod end bolts are good for wet and corrosive environments—for maximum mounting flexibility, cut the fully threaded shaft to whatever length you need.

These alloy steel rod end bolts have the highest tensile strength of any fully threaded rod end bolt we offer.

Also known as swing bolts and eyebolts, these internally threaded rod end bolts have no moving parts. They're designed to make pivoting or hinge movements in applications that don't need to compensate for misalignment.

These black-oxide steel rod end bolts are heat treated for added strength.

Good for general purpose applications where corrosion and high strength aren’t a concern, these rod end bolts are made of carbon steel.

Made of stainless steel, these rod end bolts are more corrosion resistant than steel rod end bolts.

Also known as rod‐end bearings, ball joint rod ends have an eyelet and a ball that swivels to support angular misalignment.

A carbon fiber-reinforced insert or PTFE liner reduces wear, handles shock loads, and eliminates the need for lubrication.

Connect your grease gun to the fitting to lubricate. Internal threads mate with rod end bolts, threaded rods, and other components with male threads.

An oil-embedded bronze insert slowly releases lubricant throughout the life of these internally threaded rod ends.

These internally threaded rod ends have an oil-embedded bronze insert that slowly releases lubricant over time. Connect your grease gun to the fitting to relubricate.

With at least 55° of ball swivel, these externally threaded rod ends accommodate greater misalignment than any other we offer.

Made of cadmium-plated steel, these internally threaded rod ends generally handle higher loads than stainless steel, aluminum, and nylon rod ends.

Made to extremely tight tolerances, these internally threaded rod ends are for applications that require positioning accuracy, such as accelerators and other types of control linkages.

Made of stainless steel, these externally threaded rod ends provide excellent corrosion resistance.

These anodized aluminum rod ends are lighter than stainless steel rod ends and have good corrosion resistance.

Made of impact-resistant nylon, these internally threaded rod ends withstand corrosion as well as fuels, lyes, and weak acids. They do not require lubrication and are 80% lighter than steel rod ends.

These externally threaded steel rod ends handle loads that are at least 25% higher than other comparably sized rod ends.

These internally threaded rod ends have an innovative body design that keeps the ball from being pushed out when supporting thrust loads.

Along with internal threads, these rod ends have a double row of precision ball bearings that allows high speeds and smooth operation.

Decrease the ID of your rod end to allow approximately 60° of misalignment.

The ring pivots 90° or 180° to secure loads in various directions.

Dimples hold the base tight to prevent it from swiveling.

Also known as pad eyes, these rigid rings provide a strong, fixed anchor point.

Accommodate ties in any direction with these rings that swivel all the way around and pivot 180°.

Adhesive on the back holds these rings in place.

Use these guides to position a rope.

Also known as footman's loops, use these guides to prevent webbing from twisting, or as anchor points in tie-down applications.

No need for drilling or welding—these guides mount with adhesive.

Use these brackets to mount wooden 2×4 beam for economical load bracing.

Contain and organize bulky and oddly shaped loads with these nets.

These straps have a ratchet buckle that tightens incrementally for maximum tension.

Set the amount of tension on these straps to prevent damage from overtightening. They have a ratchet buckle that tightens incrementally.

These guides have a flat slot that accepts webbing and prevents it from twisting.

Snap these hooks into track to hang equipment or attach straps.

Contain and organize bulky and oddly-shaped loads with these nets.

Slide these hooks into track to hang equipment or attach straps.

Mount threaded accessories onto track.

You can use these versatile hangers in a threaded hole (as you would a screw), or secure them with a nut (as you would a bolt).

Wedge these hangers in concrete and other solid materials.

These hangers are a popular choice for overhead applications.