1/4"-28 Fasteners | McMaster-Carr

Filter by

System of Measurement

Thread Size

Length

Material

Stainless Steel

Fastener Head Type

Threading

Partially Threaded

Threaded on Both Ends

Threaded on One End

Drive Style

Drilled Spanner

External 12-Point

External Square

Tamper-Resistant Hex

Tamper-Resistant Torx

Finish

Cadmium Yellow-Chromate Plated

Corrosion-Resistant Coated

Dry Film Lubricated

Phosphate Coated

Tin Zinc Plated

Zinc Flake Coated

Zinc Yellow-Chromate Plated

Thread Type

Thread Spacing

Socket Head Profile

Specifications Met

Federal Specification

Thread Direction

Right Hand and Left Hand

Head Diameter

Tensile Strength

20,000 psi to 29,999 psi

30,000 psi to 99,999 psi

100,000 psi or greater

Head Height

Thread Fit

Metric Class 6g

Metric Class 6H

Unified Standard Class 1A

Unified Standard Class 1B

Unified Standard Class 2A

Unified Standard Class 2B

Unified Standard Class 3A

Unified Standard Class 3B

Fastener Strength Grade/Class

Drive Size

DFARS Specialty Metals

RoHS

Compliant with Exemptions

Export Control Classification Number (ECCN)

Tip Type

Nut Type

Tamper Resistant

With Sight Hole

Hardness

REACH

How can we improve?

1,916 Products

Fastening and Joining

Socket Head Screws

Socket Head Screws

With a deeper drive than flat and rounded head screws, these withstand more torque for a tighter hold

Hex Head Screws

Hex Head Screws

Used with nuts to create a stronger joint than flat and rounded screws

Rounded Head Screws

Rounded Head Screws

Sit just above the surface for a low-profile finish and hold tighter than flat head screws

Flat Head Screws

Flat Head Screws

Fit in countersunk holes for a flush finish that won't snag on surrounding parts

12-Point Screws

12-Point Screws

12 contact points handle more torque than a hex head while a flange eliminates the need for a washer

Shoulder Screws

Shoulder Screws

Rotate parts around the cylinder under the head to guide and align them during installation

Tighten and loosen by hand without the need for tools

Set Screws

Exert pressure at the tip to hold parts in place, unlike screws that hold material together with threads

Captive Panel Screws

Captive Panel Screws

Secure panels and enclosures while still having access to them

Tapping Screws

Fasten a range of materials together without needing to tap the hole first

Hanger Bolts

Suspend pipe and other fixtures with wire or cable ties

Locknuts

Hold fasteners in place to prevent loosening from vibration

Hex Nuts

Handle most general fastening needs

Flange Nuts

The flange distributes pressure, so you don't need a washer

Easy to tighten and loosen by hand for making frequent adjustments

Cap Nuts

Cover and protect threads while adding a finished look; also known as acorn nuts

Coupling Nuts

Connect and extend threaded rods

Socket Nuts

Install in recessed holes and tight spots where a wrench won’t fit; also known as Allen nuts

Sealing Nuts

Prevent leaks and block out contaminants with a rubber seal

Square Nuts

Flat sides won’t spin in channels and square holes

Tamper-Resistant Nuts

Tamper-Resistant Nuts

Hard to detach without special tools to prevent unwanted removal

Rivet-Mount Nuts

Rivet-Mount Nuts

Add threads in hard-to-reach areas and materials that are too thin to be tapped

Rivet Nuts

Add threads to thin panels with access from only one side; also known as blind inserts

Threaded Inserts

Threaded Inserts

Create new threads or repair stripped threads

Adhesive-Mount Nuts

Adhesive-Mount Nuts

Attach threads to material that’s too thin for a threaded insert

Press-Fit Nuts

Push into drilled or punched holes to add threads to thin panels

Weld Nuts

Weld to metal surfaces to add permanent threads

Threaded Rods

Anchor, connect, or hang components in a wide variety of applications

Taper Pins

Fit snugly into tapered holes to secure, position, and align components

Binding Barrels and Screws

Binding Barrels and Screws

Thread together for a low-profile fastener

Thread Adapters

Thread Adapters

Join threads of a different type, size, and gender

Single-End Studs

Single-End Studs

Use the unthreaded end as a pivot point, hinge, shaft, or locator pin

Rivet Nut Tools

Rivet Nut Tools

Install rivet nuts

Rivet Tools

Install and remove blind, solid, hollow, and other types of rivets

Building and Machinery Hardware

Knobs

Position, tighten, and secure fixtures and equipment

Handle Nuts

Attach to threaded shafts to quickly turn the shafts by hand

Power Transmission

Lead Screws and Nuts

Lead Screws and Nuts

Components travel along a screw with broad, square threads to clamp and lift heavy loads

Rod Ends

Use with connecting rods to support loads and control steering, tensioning, or pivoting motion

Connecting Rods

Connecting Rods

Use with rod ends and swivel joints to link components in push/pull assemblies

Fabricating and Machining

Lathe Tool Insert Holder Replacement Parts

Lathe Tool Insert Holder Replacement Parts

Replace clamps, screws, shims, and other parts in lathe tool insert holders

Fixture Clamps

Secure your workpiece to a fixture table so it won't move during machining

Material Handling

Turnbuckles

Twist the body or end fittings to adjust the length and tension of attached rope and chain

Eyebolts

Route rope through the loop or attach hooks and shackles for lifting

The quick brown fox jumped over the lazy dog. Pedestal (35" Ht. x 4" Wd. x 4" Dp.)