These shaft supports hold linear shafts perpendicular to the mounting surface.

These flanges are for low-pressure applications in noncorrosive environments.

Also known as Pressure Class 300 flanges, these medium-pressure flanges have a galvanized finish for fair corrosion resistance.

Also known as Code 61 SAE hydraulic flanges.

Bolt two flanges of the same size together with a gasket to create an access point in a pipe line.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Forged for extra strength, these heavy duty unthreaded flanges can withstand high-pressure applications.

Tap into your line in systems operating up to 1,400 psi to vent pressure, drain liquid, or take samples. Made of black-coated steel, these bleed rings should be used in dry environments to prevent rusting.

Also known as Pressure Class 150 flanges, these corrosion-resistant flanges are designed for low-pressure pipe applications.

Also known as Code 61 SAE hydraulic flanges.

Also known as Code 61 SAE hydraulic flanges.

Bolt two same-size flanges together with a gasket to create an access point within a pipe line.

Butt-weld fittings allow for a smooth, flush connection that provides maximum flow.

Create an access point in systems operating up to 230 psi where corrosion is a concern. Made of stainless steel, these bleed rings resist rusting.

Also known as Pressure Class 125 flanges, these are for use in low-pressure applications. Flanges are aluminum, which is lightweight with good corrosion resistance.

Bolt these flanges to another same-size flange with a gasket to create an access point within a pipe line. They are also known as Silbraze flanges.

Bolt two same-size flanges together with a gasket to create an access point within a line. They are also known as Pressure Class 150 flanges. They have thick, strong walls to handle heavy duty industrial plumbing and water supply applications, such as water processing, waste water treatment, and irrigation.

Bolt two same-size flanges together with a gasket to create an access point within a line. Also known as Schedule 40 flanges, they are the industry standard for gravity-flow drain, waste, and vent (DWV) applications.

Use these polypropylene flanges in outdoor environments—they resist the damaging effects of ultraviolet light. They have the chemical resistance to stand up to acids, solvents, and other harsh substances. Bolt two same-size flanges together with a gasket to create an access point within a line. Flanges are also known as Pressure Class 150 flanges.

The grooved ends on these flanges connect to pipe with a clamp, so you can access your chemical process line for routine maintenance. Flanges have excellent chemical resistance to withstand a variety of salt solutions, acids, and other harsh substances. They are also known as Victaulic flanges.

Connect quick-clamp sanitary tube fittings—also known as aseptic fittings—for a fast and easy way to access your line.

Connect extra-support quick-clamp fittings for a fast and easy way to access your line.

Use these rings with quick-clamp high-vacuum fittings.

Also known as KF, QF, and NW fittings, these fittings are for high-vacuum applications, such as vacuum coating and heat treating, leak testing, and analyzing gases.

For high-vacuum systems with tube sizes too large for quick-clamp (KF) fittings, choose these bolt-together fittings.

Use these fittings at pressures up to 9,700 psi. Also known as instrumentation fittings, they are made to tight tolerances for use in high-precision applications. They are compatible with Swagelok®, Let-Lok, and Parker A-Lok fittings.

Create airtight seals in high-vacuum systems by placing these rings between two claw-clamp (ISO-K) or bolt-together (ISO-F) fittings.

Crimp these fittings to copper tubing with a crimping tool for a leak-tight connection that doesn’t require heat or soldering. They are comparable to Viega ProPress fittings.

Use these clamps with quick-clamp fittings for dairy to quickly connect and disconnect your line as needed.

Couplings are metal, which has better durability than plastic cam-and-groove hose couplings. They consist of a plug and a socket that connect and disconnect quickly. Use them if you need frequent access to a line. To connect, insert the plug into the socket and push the levers down.

Ball bearings operate with less friction than other bearings, so you can run them at higher speeds.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with two-bolt flange.

Use these bearings for light loads and small shafts. The closed backing blocks out dust and other contaminants.

The lubricant in these mounted ball bearings is suitable for incidental contact with food.

Use these nylon or acetal bearings for light loads. The closed backing blocks out dust and other contaminants.

Made of FDA listed PEEK, these bearings are suitable for direct contact with food. The closed backing blocks out dust and other contaminants.

Capable of handling temperatures from -400° to 750° F, these graphalloy bearings have the widest temperature range of any of our mounted bearings.

A bolt in each corner makes for a secure, even hold.

Use these bearings in corrosive environments and under water.

Synthetic grease enables these bearings to operate in temperatures up to 400° F—nearly double the maximum temperature of standard mounted ball bearings with four-bolt flange.

With no moving parts, sleeve bearings are better for dirty environments than ball and roller bearings.

Create a custom mounted bearing by adding your own bearing to these flanged housings.

Half the weight of steel, this aluminum framing resists corrosion in wet environments.

Stronger than plastic and aluminum, this is the lightest weight framing we offer. It has good resistance to chemicals and salt water.

Fittings come in two pieces to wrap around rails, so you can quickly modify existing structures without disassembling. Use clamp-on framing and fittings to form temporary partitions, modular conveyors, and workstations.

No need for fasteners—friction holds this framing together. Use press-fit framing and fittings to assemble carts, enclosures, and partitions.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Also known as trapezoidal-thread lead screws and nuts.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Keep your ball screw spinning without the ball nut damaging your system. When the ball nut reaches the stop pin at either end of the ball screw, it disengages and begins to idle.

Multiple thread channels (also known as thread starts) create faster linear travel than ball screws with a single thread start.

Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts.

Found in hand-powered clamps, vises, grates, doors, and work tables, lead screws and nuts have broad, square threads that are well suited for quick assembly, high clamping forces, and lifting and lowering heavy objects.

Bolt flanges to equipment to start a run of duct.

Equip your robot arm with two tools at once—these mounts have two offset, angled mounting surfaces for tools.

Add a finishing touch to the area around protruding pipes with these corrosion-resistant plates, which are also known as escutcheons.

Made of Kevlar, these are the most durable breathable round bellows with flange ends. They also protect against sparks and weld spatter.

No need to disassemble equipment—these bellows wrap around moving parts. Sewn seams let them breathe, so they retract quickly in fast-cycling applications.

Slide these bellows over square rods and shafts.

These bellows withstand temperatures up to 500° F—more than twice as much as standard flat bellows.

Attach the cuff end with a hose clamp, and screw mount the flange end.