These leveling compounds stand up to acid and chemical spills, making them a good choice for corrosive environments. They also withstand steel-wheel traffic and heavy impact. Apply with a trowel. They're ready for foot traffic in 12 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Give new life to damaged and worn concrete floors. These leveling compounds also fill minor depressions and cracks. Apply with a trowel.

Epoxy compounds resist abrasion for use in high-traffic areas. They’re ready for foot traffic in 8 hours. The resin and hardener are in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts.

Fill in and shape horizontal, vertical, and overhead concrete surfaces, such as steps and columns.

Epoxy surface fillers are nonsagging. They resist oil, grease, water, alkalies, and chemicals. Application time, after mixing, is 1 hour. The size listed is the combined total of the two parts.

Fill cracks up to 10" deep on vertical and overhead surfaces. To use this filler, secure the included injection ports to the crack with the two-part epoxy sealer, then spread sealer over the entire crack. Allow sealer 24 hours to cure. Application time for sealer, after mixing, is 40 minutes. To fill the rest of the void, use the cartridge with a standard caulk gun (sold separately) to dispense the two-part epoxy filler into the injection ports.

Fill cracks up to 4" deep on horizontal surfaces such as floors and sidewalks. These epoxies are shrink, impact, and chemical resistant, and can also be used on wood, fiberglass, and metal surfaces. Use the cartridges with a standard caulk gun (sold separately) for dispensing.

Fill cracks in horizontal, vertical, and overhead concrete surfaces. Surface fillers that have a mix ratio are multi-part fillers. Size listed is the combined total of the parts.

Knead surface fillers in a stick to a uniform color to mix and press them into cracks in concrete floors, stairs, and walls. They can also be used to anchor bolts.

Knead the epoxy-coated patch and resin together to make repairs to pipes, tanks, drums, and containers in the field.

Everything you need to repair cracked, worn, and damaged surfaces—even underwater.

These coatings are more durable than our standard coatings for concrete floors. They provide a stain-resistant finish that protects your floors from moisture, chemicals, foot traffic, and hand carts. Repair cracks and holes prior to application. Apply with a squeegee, roller, or sprayer. The size listed is the combined total of the two parts.

Use these solvent-free, high-gloss coatings to protect concrete floors in enclosed areas. Durable enough for forklift traffic, they resist stains, moisture, and chemicals. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts.

Longer-lasting than antislip tape, these coatings contain grit to provide traction. They’re good for areas with pedestrian traffic.

Water-based epoxy coatings are clear and can be applied over nearly any surface, even old coatings, without altering their appearance. These two-part coatings come with a mixer that attaches to a hand-held drill and a roller cover to apply them once mixed. The size listed is the combined total of the two parts.

Apply acrylic coatings with a roller or sprayer. Apply gallon-sized water-based coatings with a roller. Apply gallon-sized solvent-based coatings with a notched trowel, sprayer, or a roller cover for thick coatings (sold separately).

Coatings that comply with OSHA 29 CFR 1910.22 meet requirements for walking-working surfaces.

These high-traction antislip coatings have zero VOCs and are low odor. They contain grit to provide traction for pedestrian, cart, and hand-truck traffic. Apply with a roller. The size listed is the combined total of the two parts.

These provide the highest traction and impact resistance of our antislip coatings. Longer-lasting than antislip tape, these coatings contain grit to provide traction. Apply with a roller. The resin and hardener come in separate containers that can be mixed in the pail. The size listed is the combined total of the two parts. They cannot be sold to the regions listed because they exceed local regulatory limits on VOCs (volatile organic compounds).

Coatings that meet MIL-PRF 24667 Type 1 are our most wear and impact resistant. They can also be applied with a notched trowel.

Designed for use in areas with heavy vehicular traffic, these coatings are highly resistant to wear. They contain grit to provide traction to your surface. Apply with a notched trowel, roller, or sprayer. The size listed is the combined total of the two parts. They cannot be sold to the regions listed because they exceed local regulatory limits on VOCs (volatile organic compounds).

Coatings in a pail have a resin and a hardener in separate containers that can be mixed in the pail.

These thin primers penetrate deeply into concrete floors to create a hard surface that can then be coated with any urethane or epoxy coating. Primers resist abrasion and chemicals, such as mild acids, alkalies, salt, and fuel. Apply with a roller. The size listed is the combined total of the two parts.

Use these primers on your surface before antislip coatings to maximize longevity. They do not contain grit. Apply with a brush, roller, or sprayer. The size listed is the combined total of the two parts. They cannot be sold to the regions listed because they exceed local regulatory limits on VOCs (volatile organic compounds).

Bond new concrete to old concrete, or use this epoxy as a primer for epoxy coatings on concrete surfaces. Mix the amount you need; the size listed is the combined total of the two parts.

Thinner than non-sagging sealants, these flow easily into cracks and have a smooth finish.

Elongation indicates flexibility—the higher the value is, the more joint movement a sealant can sustain. For high-wear applications, choose a harder sealant for the most abrasion resistance.