Slide the bolt and drop the knob into the notch to hold, then secure with a padlock.

These padlockable latches are reversible for right- and left-hand mounting.

These padlockable latches are often used on 2" and 3" track to keep garage and other sectional overhead doors closed.

Slide the bolt and drop the knob into the notch to secure.

No hands needed—step on the top cap to latch the bolt; retract it by pressing the side release button.

Push the bolt into the strike plate to secure doors, gates, and cabinets.

Pull the chain-grip to unlatch hard-to-reach doors and panels.

Choose these locks if you need several locks that open with the same key.

Designed to stand up to heavy use, these latches are often seen on refrigerators and truck doors.

Latches snap shut when you push the bar in the strike plate to prevent accidental unlatching. Press the button on the strike plate to release the bar.

To prevent accidental unlatching due to vibration, there's a bushing in the eye.

With a key-locking mechanism, these locks provide more security than other gate locks.

Secure swinging doors in wire and chain link partitions.

A hidden push-button release on the bottom of these latches retracts the latch bolt; this discourages unwanted entry but allows access to those who know it’s there.

Maintain security by keeping your door latched as you open it up to 3".

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges.

These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging.

Wide hinge leaves provide a large mounting surface to keep trailer doors from sagging.

Open doors past their frame to make extra room for people and large items, such as carts, furniture, and wheelchairs, to pass through.

Turn a set screw to adjust the door up or down after it's hung.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Turn a set screw to adjust the door 1/8" up or down after it's hung.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Thick leaves and a large diameter pin make these hinges good for use with heavy doors.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

Also known as bullet hinges, these hinges are the right size for tight spaces and narrow frames.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

Use these hinges on lightweight screen and storm doors as well as small gates.

Springs in these hinges with holes automatically swing doors and gates closed behind you.

Springs in these hinges without holes automatically swing doors and gates closed behind you.

These hinges without holes are spring loaded—pull the handle to retract the pin and disconnect a door; release the handle and the pin snaps back.

To retract the pin and disconnect a door, squeeze the hinge handles together. Release the handles and the pin snaps back.

Squeeze the hinge handles together to retract the pin and disconnect a door; release the handles and the pin snaps back.

A stop keeps these hinges open at a set angle; push past the stop to open them to 180°.

In addition to rotating 360°, these hinges tilt up and down.

Tighten or loosen an adjustment screw to change the hinge resistance.

Eliminate slamming lids—these hinges hold lids open at their widest angle and then slowly pull them closed.

A stud projects from the back of each hinge leaf to prevent the door from being forced open. The mounting holes form an industry-standard half-moon shape.

Bearings allow these hinges to open and close doors smoothly. The mounting holes form an industry-standard half-moon shape.

No need for oil or grease, these hinges are maintenance free. The mounting holes form an industry-standard half-moon shape.

Bearings allow these hinges to open and close doors smoothly.

A snap-on cover protects these hinges from tampering and creates a finished appearance.

The hinge pin is permanently attached to the frame leaf so you can quickly lift the door off the hinge without removing the pin.

The mounting hole pattern does not follow an industry standard, which means you can work around worn mounting holes when replacing template hinges.

The mounting holes form an industry-standard half-moon shape.

Plastic bushings on these metal hinges prevent metal-to-metal contact that can release particles as hinges open and close.

Designed to wrap around the edge of the partition frame, these hinges provide a stronger hold than other toilet partition door hinges.

No need for drilling holes or welding, slip these hinges onto panel and door edges for a secure fit.

Made of carbon fiber, these hinges are as strong as aluminum yet lighter in weight. All have leaves that are connected by a strip of flexible Kevlar instead of a pin.

Plastic hinges are a lightweight alternative to metal hinges and provide smooth, silent operation.

The leaves of these hinges almost touch when the door is closed. They are often used in electrical enclosures for a tight seal.

Eliminate slamming doors—push the door and these hinges slowly pull it closed.

Surface-mount these hinges to the side of a cabinet.

Easier to install than other mortise-mount concealed cabinet hinges, these fit in two drilled holes.

Instead of mounting to the side of a door, mount these hinges to the top and bottom to allow doors to open wide.

With a 170° range of motion, these hinges are for doors that need to open wide.

Slip the hinge pins into 11/32" Dia. × 5/16" Dp. holes in a cabinet.

A flange on one or both sides of the wheel keeps your equipment running on square structural tubing and other rails.

The wheels of these casters have a 90° V-groove and a flat tread to move your equipment on angle-iron track as well as the floor.

A flange on one side of the wheel keeps your equipment running on square structural tubing and other rails.

The wheels of these casters have a 90° V-groove and a flat tread to move your equipment on angle-iron track as well as the floor. The 303 stainless steel wheels are suitable for steam-cleaning applications.

These wheels have a 90° V-groove and a flat tread to move your equipment on angle-iron track as well as the floor.

Make your own wheels by cutting these wheel blanks to size with a band saw. They're easy to machine so you can create V-groove and flanged wheels, as well as conveyor rollers and pulleys.

These complete sets contain everything you need to create a system for hanging doors.

Narrow track allows you to hang doors in tight spaces.

Keep garage doors and other overhead doors rolling smoothly.

These complete sets contain everything you need to create a system for hanging doors.

These sets include everything you need to hang two doors that slide past each other.

For smoother operation, these sets include upper and lower roller track for hanging lightweight cabinet doors that slide past each other.

No need for drawer slides or roller track—add rollers to wood cabinet drawers and doors for smooth operation.