Use these metric mounts on heavy machines and equipment.

Meant for light duty applications, these mounts are not rated for capacity.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.

Install these mounts on machines without feet.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Zinc-plated steel is more corrosion resistant than nickel-plated steel.

Made of 303/304 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Broader, stronger threads enable faster adjustments and higher load capacities than standard V-shaped threads.

Black-oxide steel has a dull shine for areas where appearance is a concern.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Made entirely of 316 stainless steel, these mounts are our most resistant to corrosion from chemicals, solvents, and water.

An integral cushion reduces noise and vibration.

These feet are made of UHMW polyethylene plastic, so they won’t dry out and become brittle.

Peel back the film to stick these feet to the bottom of furniture and equipment legs.

Press these feet into tubular legs of tables, chairs, and other furniture.

These feet have angled or rounded bottoms to work with tubular furniture legs that meet the floor at an angle.

Place these feet under furniture and equipment.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

Higher deflection ratings translate to greater vibration and shock isolation.

Bolt these mounts down to keep your equipment stationary.

A two-piece design requires less clearance than one-piece mounts and simplifies installation—raise your machine just enough to slide the base underneath, then insert the stud from above.

Mate with a T-slotted rail to add linear motion to your assembly.

With a wide base, these sleeve bearing carriages stabilize moment (twisting) and off-center loads better than standard carriages. Use in areas where multiple carriages or rails won't fit.

With fewer moving parts and no need for lubrication, sleeve bearing carriages perform better in dusty and wet environments than ball and roller bearing carriages. They're also better at handling impact and vibration.

Use these carriages and guide rails in temperatures up to 300° F.

Fasten loads on the side of these carriages and add linear motion to a T-slot assembly.

The square profile prevents loads from twisting and rotating.

Mount along a wall or other vertical surface.

Use these carriages and guide rails for light loads where precise movement is not required.

Needle-roller bearings give these track roller carriages higher load capacities than other track roller carriages.

High-temperature PTFE-thickened grease enables these carriages to operate in temperatures up to 500° F, higher than any other carriage that we offer.

Nylon rollers provide low-friction movement for light loads and corrosive environments.

These carriages and guide rails are steel.

Made of stainless steel, these carriages and guide rails are more corrosion resistant than steel carriages and guide rails.

A plastic cage surrounds the ball bearings and keeps them from colliding, so these carriages run for many cycles without needing maintenance.

Suitable for clean room use, these carriages and guide rails are made entirely of stainless steel.

With a plastic cage that surrounds the ball bearings to prevent them from colliding, these extra-wide carriages run quietly for many cycles without needing maintenance. All of these carriages have a wide base and low-profile design to stabilize moment (twisting) and off-center loads better than other carriages.

Mount to vertical surfaces for applications where tight tolerances aren't required.

Made of stainless steel, these track rollers and guide rails are more corrosion resistant than steel rollers and rails.

With a row of crossed-roller bearings on each side of the rail, these slides have over twice the load capacity of standard low-friction slides and are better for handling shock loads.

Create your own positioning table or telescoping slide. Sets include four rails, two roller bearing cages, and eight end stops.

Use these slides in a variety of manual-positioning applications for laboratory and production equipment as well as for positioning parts for drilling, fastening, assembly, and measuring.

Two micrometer handles ensure accurate, repeatable positioning along two axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

A thumb screw locks the slide to prevent movement in systems where vibration is present.

Three micrometer handles ensure accurate, repeatable positioning along three axes—good for positioning parts, such as measuring and inspecting equipment, that are part of a larger automated system.

Install these drawer slides in small-parts cabinets.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

A lever locks the drawer in the open as well as closed position; push the lever to release the lock.

These slides provide full extension for convenient access to the back of your drawers.

Slides only extend 3/4 of the closed length to reduce the chance that a heavy load will tip your cabinet.

The size of a finger, these tiny slides open in both directions. All have ball bearings for smooth operation.

These slides gradually slow the drawer's motion to prevent it from slamming open.

To prevent drawers from slamming shut and support them even if they’re tall and full of heavy equipment, these steel slides have soft-closing bumpers and mount to the top and bottom of drawers.

Press these bumpers into place with the adhesive backing. Use them as feet and spacers on instruments and small appliances to limit sliding, vibration, and noise. They're comparable to Bumpon bumpers.

Also known as universal casters, press-fit these casters into standard 1" OD wire shelving posts.

Often used on furniture, the hood covers the wheel for a more finished appearance.

Wheels range from soft rubber that absorbs shock while providing good traction on rough surfaces, to hard, impact-resistant rubber that rolls easily on smooth surfaces.

Create a seamless joint between the top of these casters and the bottom of most swivel chairs.

The most durable plastic wheel, the nylon wheels on these casters are impact and wear resistant. They work well on smooth surfaces. The wheels dissipate static to protect sensitive electronic equipment from electrostatic discharge.

Press-fit these casters into sockets on Rubbermaid carts with a 7/16" Tube OD.

These casters are offered with low mount heights to keep equipment such as business machines and display fixtures stable.

Insert any 1/2" dia. Grade 8 bolt through the hole in the frame to create a custom-length stem.

Use these general purpose casters in a variety of applications.

Also known as twin-wheel casters, these lightweight and economical casters are often used on furniture and displays.

As the standard for plastic wheels, phenolic wheels are nonmarking and perform well at high temperatures. They roll best on smooth surfaces but can be noisy.

Customize the length of your stem by adding any 1/2" dia. Grade 8 bolt through the hole in the frame.

Rubber wheels on these casters dissipate static to protect static sensitive electronic equipment from electrostatic discharge.

Polyurethane wheels combine the abrasion resistance of plastic with the shock- and sound-absorbing qualities of rubber. Use them on smooth or rough floors and in areas with debris. Their 304 stainless steel frame is corrosion resistant.

A nylon frame gives these casters the corrosion resistance you need for equipment that’s frequently washed down. Their soft rubber wheels are shock absorbing and provide good traction on rough surfaces.

The stem on these casters fits into square tubing and can also be bolted to angle iron.