Deliver small amounts of grease with only a light push against the lubrication point.

Turn a small tube of grease into a dispenser.

Because of their one-hand operation, pistol-grip grease guns are easier to use for adding grease to hard-to-reach places than lever-grip guns.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

These guns deliver twice as much grease per stroke than standard lever-grip guns.

Dispense grease with the highest-pressure-rated gun we offer.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Use compressed air to dispense grease.

These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Sets include dispensing tips for grease fittings and bare lubrication points.

Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Mount holders in convenient locations to keep grease guns within reach.

Attach these nipples to guns to load grease from bulk filler pumps.

Tighten the cover to dispense grease.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Useful in remote areas without access to air or electrical power.

Apply lubricant to gear racks with a 14 1/2° pressure angle and a pitch of 16.

Dispense grease using compressed air.

A display allows you to monitor how much grease is dispensed.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

More portable than air-powered options, attach this dispenser to a battery to deliver grease on the go.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Serve multiple lubrication points from a single location.

A solenoid automatically starts and stops flow to dispense lubricant while equipment is running.

Customize these dispensers to serve up to 24 lubrication points from a single location.

Serve multiple lubrication points from a single location.

Connect a tube fitting and tubing to the dispenser outlet to access hard-to-reach lubrication points.

For use in clean environments, these oil reservoirs have multiple air vents that keep pressure balanced.

A sealed design prevents contamination in dirty and dusty environments.

Mount these directly to your machine—the cup allows oil to gradually pass through to equipment, reducing time spent on manual lubrication.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Manually adjust the flow of oil to a single lubrication point.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

Clamp this applicator around control cables to lubricate them with minimal mess.

Pull the trigger on these oilers for easier one-hand operation than standard hand-held oil dispensers.

These manual dispensers are more portable than air-powered dispensers.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum.

The most versatile of our machine-mount coolant nozzles, these adjust from a fine mist to a direct stream and can deliver coolant in any direction. Max. pressure is 100 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Deliver a small, controlled amount of coolant to a workpiece.

Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.

Draw coolant from your existing tank.

Kits contain lengths of hose, nozzles, valves, and caps.

Use with Loc-Line hose to assemble and disassemble components.

Build a custom 3/4" system to deliver coolant, cutting oil, water, or air in any direction.

This hose is made of steel.

Assortments contain straight, 45° elbow, and 90° elbow fittings.

Keep thin grease from leaking out—the check valve on these fittings has a Buna-N seat that creates a tighter seal than check valves on other grease fittings.

Inject lubricant into motors, bearings, engine blocks, and all kinds of machinery.

Ensure a secure fit in unthreaded holes—these fittings cut threads as they’re installed. Use these fittings in tight spaces where protruding fittings won't work.

Drive these fittings into unthreaded holes. They're also known as hydraulic grease fittings.

When the size or thread type of a fitting doesn't match an existing opening, use these adapters to make the connection.

Keep standard grease fittings free of dirt and moisture.

Tap these tools once or twice with a hammer to install fittings.

Lubricate multiple points from a single location.

Install these fittings into threaded holes.