Use these wheels for light grinding, deburring, and sharpening.

The perforated honeycomb pattern cuts carbide, ceramics, and glass without the need for cleaning.

A good value for everyday use, these wheels offer an economical balance between heavy material removal and long life. They are also known as Type 27 wheels, raised-hub wheels, and grinding discs.

A blend of ceramic alumina and zirconia alumina removes material at a 50% faster rate than our Long-Life Grinding Wheels. Wheels are also known as Type 27 wheels, raised-hub wheels, and grinding discs.

The absence of iron, sulfur, and chlorine in these wheels means they won’t corrode or discolor stainless steel. They are also known as INOX wheels, Type 27 wheels, raised-hub wheels, and grinding discs.

Heat-dissipating holes reduce material buildup and extend the life of the wheel. Wheels have a semiflexible backing that conforms to curved and rough surfaces.

Multiple layers of nylon mesh embedded with abrasive provide a cushioned grind. Also known as unitized discs or wheels.

A blend of cotton laminate and aluminum oxide creates a smoother surface than other grinding wheels with similar grits. Wheels are also known as Type 27 wheels and raised-hub wheels.

Wheels have a large surface area and a thick layer of rough abrasive for heavy material removal on concrete and stone. They are also known as Type 11 wheels, flared-cup wheels, snagging wheels, and cup stones.

Use these wheels for precision grinding on surface, cylindrical, and tool and cutter grinders. They are also known as Type 1 wheels and straight wheels.

The special shapes of these wheels provide more clearance than typical straight wheels.

The porous bond leaves more space between abrasive grains so heavy amounts of chips and coolant easily flow through.

Use these wheels for heavy material removal in one spot or along a weld seam. They are also known as Type 1 wheels and snagging wheels.

Wheels remove more material than other grinding wheels with cotton laminate.

Also known as hooded dressers, these cleaners reveal new layers of sharp abrasive and deflect flying chips.

The larger face offers better control, while multiple points provide a finer finish than single-point cleaners.

The single point on these cleaners removes more material than multiple-point cleaners.

Furnished with multiple points, these clean faster and leave a more uniform finish than single-point cleaners.

Mount these cleaners to the T-slot of your surface grinder or secure them to a magnetic chuck.

Mount these truing cleaners to a T-slot to reshape worn diamond and CBN grinding wheels.

Made of aluminum oxide, these bits are well suited for use on most metals and materials that are not heat sensitive.

Bits thread onto mounted shanks so you can quickly switch head shapes without removing the shank. The abrasive grains are blended with rubber, which cushions during grinding to produce a smoother surface texture than other bits with similar grits.

The bits in this set have rubber blended into the abrasive, which cushions during grinding to produce a smooth to extra-smooth surface texture.

Bits stay cool during grinding so they won’t mar or discolor stainless steel.

Use bits in any drill chuck that accepts a 1/4" hex shank.

The small 3/32" diameter shank and small head makes these bits good for precise and intricate jobs.

The diamond abrasive in these bits is extremely hard and lasts longer than tungsten carbide. For longer tool life and improved finish, use a water- or oil-soluble mist or coolant.

With more flaps than standard discs, these last 30-40% longer.

With more flaps than standard discs, these last 30-40% longer.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating more consistent finishes.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

The flaps wrap around the outer edge of these discs to sand welds at right angles.

These discs have a harder abrasive than standard flap sanding discs.

The backing plate on these discs can be sheared away as the abrasive flaps wear down, allowing you to use more of the disc rather than replacing with a new one.

A coating prevents dust and debris from building up on the abrasive surface.

A special fastener on the back of these discs allows you to easily swap one disc for another.

These discs have a harder abrasive than standard quick-change discs.

These discs have a harder abrasive than standard flexible-edge quick-change discs.

Debur, clean, and blend faster than other nylon mesh discs.

Used for heavy cleaning and stripping, these discs have an abrasive-embedded nylon mesh construction that gives you more control over sanding pressure.

The heavy duty construction provides more support than standard discs for heavy material removal.

Fit these discs over your tool’s arbor.

A coating prevents dust and debris from building up on the abrasive surface.

The abrasive-embedded mesh construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer.

The premium abrasive stays sharp longer. Holes in the disc let you see the surface you’re sanding.

Fit these discs over your tool's arbor to sand masonry, ceramics, and composites.

Press onto a compatible sanding tool or backup pad; peel off to remove.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Holes allow dust removal when used with a vacuum sander.

These discs have a long-lasting diamond abrasive.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

The thick, abrasive-embedded nylon mesh construction gives you maximum control over sanding pressure.

These discs are abrasive-embedded cloth with a cushioned layer.

Quickly attach, remove, and reuse these discs with a compatible sanding tool or backup pad.

The premium abrasive lasts longer as well as cuts faster and produces a more consistent finish than standard hook and loop discs.

The mesh backing lets sanding dust and debris escape during use, preventing material build up on the abrasive surface.

The cushioned construction gives you more control over sanding pressure, creating finer and more consistent finishes.

Use with commercial floor buffing machines to sand wood floors and strip tape from concrete.

These rubber blocks sand flat surfaces.

These pads are designed to channel air flow to the sanding disc for cooler operation, prolonging the life of the disc.

Holes in the pad align with holes in the sanding disc for a clearer view of the sanding surface.

Secure the shank into the collet or chuck of a tool.

Thread the stud into the tool's spindle.

Use screws to attach these pads to a tool.

Thread these pads onto the tool’s arbor.

Holes allow dust removal when used with a vacuum sander.