Insert a bit into the shaft and a magnet holds it in place.

Operate these tools like a standard bit driver and access hard-reach fasteners with the offset head. Insert a bit and a magnet holds it in place.

Drive screws four times faster than ratcheting alone. Grip the speed housing at the base of the shaft with one hand while turning the handle with the other. A magnet at the end of the shaft holds bits in place.

LEDs light the tip so you can use these tools in dark areas.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet EN 60900 and IEC 60900.

An insulated handle and shafts protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900.

A scaled-down version of standard changeable-shaft screwdrivers, these tools are shorter, slimmer, and easy to take with you. Remove and replace the shaft to use a different tip size.

Remove and replace the reversible shaft to change the tip of the tool. Sets include a handle and multiple shafts.

Sets include an assortment of drivers with soft, contoured handles that provide comfort and the best possible grip for achieving maximum torque.

These standard-length drivers are found in every tool box.

When working in tight spaces, these short drivers fit where others can't.

When working in tight spaces, these short drivers fit where others can't. They have a cushioned grip over a plastic core for comfort and some slip resistance.

Sets include an assortment of drivers with a cushioned grip that provides comfort and some slip resistance.

Even oily hands can keep a firm grip on the suede-like textured handle.

The assorted drivers in these sets have a ball end that allows angled entry to turn screws in hard-to-reach areas.

A holding mechanism at the tip of the tool ensures the screw won’t slip off.

The tips of these assorted drivers have ribbed grooves that grip the surface of the recess to reduce slipping and minimizing the pressure required to achieve maximum torque.

A shaft that extends through the handle and a steel end cap gives these drivers the strength to absorb hammer blows.

Bright-colored handles make these tools stand out so they're less likely to be misplaced.

Also known as hollow-tip or parallel ground screwdrivers, the straight slotted tip fills the screw slot better than the tapered tip on standard screwdrivers for more torque and less slippage.

Use the stud on the handle to bend and loop solid wire for making connections to outlets and switches.

Sets include an assortment of drivers with a ring that can be secured with a lanyard to prevent drops. The ring rotates around the shaft so the driver turns freely.

Protect your stainless steel screws by using a stainless steel driver. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These drivers eliminate that risk.

These assorted screwdrivers are made of beryllium copper that is FM approved. They help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

Made of beryllium copper that is FM approved, these screwdrivers help meet OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC, EN, or ASTM standards.

A scaled-down version of standard nutdrivers, these tools are shorter, slimmer, and easy to take with you.

When working in tight spaces, these short drivers fit where others can't.

The shaft and handle are drilled all the way through for turning nuts on any length of threaded rod. These drivers have a magnet in the tip to hold nuts in place.

Bend the shaft around obstructions to access nuts in tight spots, such as when securing hose clamps.

Protect your stainless steel fasteners by using a stainless steel driver. If steel flakes off a standard tool and into the threads, it can lead to rust and contamination. These drivers eliminate that risk.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet ASTM and IEC standards.

Adjust the nosepiece to set the depth and prevent fasteners from being driven too deep. These drivers are good for use with soft materials such as wood, fiberboard, drywall, and insulation board. They are powered by rechargeable batteries.

Mount the magnetic backing to walls, cabinets, and other steel surfaces. Magnetic slots secure your screwdrivers.

The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing.

While one-way screws can be installed with standard slotted screwdrivers, they can only be removed with these tools.

Set the desired torque and the driver indicates when it's reached.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 standards. When set torque is reached, these drivers signal with an audible click.

Set includes a handle and six shafts. Remove and replace the shaft to use a different size or drive style.

A dial shows how torque measurements change as you turn the driver. Use these tools to fasten to a specific torque, determine fastener torque specifications, and identify the torque required to loosen tightened fasteners.

Attach a socket to the 1/4" square drive tip. These tools have a dial that shows how torque measurements change as you turn the driver. Use to fasten to a specific torque, determine fastener torque specifications, and identify the torque required to loosen tightened fasteners.

Set torque and the clutch slips to prevent you from exceeding it.

Reach the same torque every time with factory-set screwdrivers that slip to disengage and stop turning the fastener when the set torque is reached, preventing overtightening.

Set torque and the clutch slips to prevent you from exceeding it.

Rated for ISO Class 5 (Fed. Std. Class 100) clean rooms, these tools have a sealed handle to keep lubrication in and contaminants out. Factory-set screwdrivers ensure you reach the same torque every time.

Ensure carbide inserts are tightened to the correct torque. These tools are set to the recommended torque values for each screw size.

Sets include an assortment of drivers with a rotating end cap on the handle that allows you to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Sets include an assortment of drivers with a tip that can be replaced when it becomes worn. Press the rotating end cap on the handle with your palm to apply constant pressure to small fasteners while turning the body of the screwdriver with your fingertips.

When you don't have exact alignment between the fastener and the tool, the ball end allows angled entry to turn screws in hard-to-reach areas. Press the rotating end cap on the handle with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

A magnetized tip holds the screw in place. Press the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Also known as ESD-safe screwdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the screwdriver with your fingertips.

Use these ceramic-tipped screwdrivers for adjusting sensitive electronic components such as capacitors and resistors. They're completely nonconductive and nonmagnetic so there's no risk of short-circuiting or creating magnetic interference. Press the rotating end cap with your palm to apply constant pressure while turning the body of the screwdriver with your fingertips.

Apply constant pressure to small hex nuts and cap screws. Press the rotating end cap on the handle with your palm while turning the body of the driver with your fingertips.

Also known as ESD-safe nutdrivers, the handle drains static away from your application, preventing buildup from electrostatic discharge (ESD) that can damage sensitive equipment. Use the rotating end cap on the handle to apply constant pressure with your palm while turning the body of the driver with your fingertips.

Use these ceramic-tipped screwdrivers for adjusting sensitive electronic components such as capacitors and resistors. They're completely nonconductive and nonmagnetic so there's no risk of short-circuiting or creating magnetic interference. Remove and replace the shafts to use a different size or drive style.

Sets include assorted keys with long shafts that reach into tight spots. The plastic-covered handles provide a good grip for your whole hand.

Sets include an assortment of short keys that fit in tight spaces where others can't.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t.

These assorted keys have a textured grip that provides comfort, slip resistance, and maximum torque. They have a long shaft for reaching into tight spots to turn fasteners.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. The textured grip provides comfort, slip resistance, and maximum torque.

With a simple loop handle, these keys are the economical choice. They have a long shaft for reaching into tight spots and the T-handle provides a good grip for your whole hand when turning fasteners.

Use the long shaft for more reach and the short shaft for more torque when turning fasteners.

The long shaft has a ball end for angled entry to turn screws in hard-to-reach areas. The short shaft provides additional torque.

These assorted keys have a ball-end tip with a retaining ring that grips inside the recess to hold screws in place and allows angled entry to turn fasteners in hard-to-reach areas.

The extra-long shaft lets you access fasteners in deep recesses. To change tips, use a hex key to loosen the set screw.

These assorted keys have a retaining ring on the tip that grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

A retaining ring on the tip grips inside the recess to hold screws in place. Often used to install carbide inserts in cutting tools, these keys have a small T-handle that prevents you from generating too much torque when turning a fastener.

The assorted keys in these sets have an insulated handle and shaft that protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900 and ASTM F1505-01. They have a long shaft that reaches into tight spots to turn fasteners.

An insulated handle and shaft protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC and ASTM standards. They have a long shaft that reaches into tight spots to turn fasteners.

Sets include an assortment of keys with a long shaft for more reach and a short shaft for more torque. Use stainless steel keys to protect your stainless steel screws. If steel flakes off a standard tool and into the recess, it can lead to rust and contamination. These keys eliminate that risk.

These assorted screw starters have a slim body that reaches into tight spots to grip and turn screws that are hard to reach or too small to hold by hand.

Sets include an assortment of screw starters for gripping and turning screws that are too small to hold by hand or located in hard-to-reach spots.

An insulated handle and body protect against shock from accidental contact with live electrical circuits. These tools are tested to 1,000 volts to meet IEC 60900. They grip and turn screws that are too small to hold by hand or located in hard-to-reach spots.

Turn fasteners from either end and reach into tight spots.

These keys have an extra-short leg to fit into tight spaces that other tools can’t.

These assorted keys have a ball end that allows angled entry to make good contact with the screw recess when standard-tip keys can’t. Use to turn screws in hard-to-reach spots.