About half the size of a standard portable lever-operated punch, these punches can fit in your toolbox.

Deliver nearly three times the punching force of a standard portable lever-operated punch by holding one handle and turning the other 360°.

A throat depth more than double those of standard bench-mount lever-operated punches allows this tool to reach further past the edge of material.

Our most powerful lever-operated punch, the rotary-action socket turns to deliver two to three times the punching force of other bench-mount lever-operated punches.

Strengthened edges cut holes up to 4" dia. in fabric, leather, rubber, and soft metal. Also known as arch punches.

Make oblong holes in fabric, leather, and rubber. Also known as arch punches.

Screw one of the interchangeable heads into the included handle to create holes up to 3/16" dia. in tight spaces.

Attach two punch heads to the handle at the same time to punch a gasket or washer in a single strike.

Sets include common ID and OD sizes to create gaskets and washers in two strikes.

The body is cast steel.

Squeeze the spring-return handle to punch round holes of a single size.

Turn the handle of these punches while pushing down to punch holes in cork and rubber.

Use a wrench to cut DIN-size holes in steel up to 1/16" thick.

Rotate the angled head of the driver up to 180° to fit it into tight spaces and supply eight tons of force to the hole punches.

The driver supplies eight tons of force to the hole punches in this set to make straight punches.

Punch conduit up to size 1 1/4.

The knurled handle of these punches offers a more secure grip than standard punches. Use pin-removal punches to knock out pins and rivets that have already been loosened.

Minimize damage to your work surfaces with these brass punches, which are softer than steel punches.

The rounded tip of these punches fits into the open ends of hollow and spring pins to protect them from damage during removal.

A soft brass body minimizes the damage these punches make on work surfaces.

A hammer and punch in one, this tool knocks out pins, rivets, and bolts.

Impact-resistant steel makes these punches stronger and more durable than standard pin-removal punches.

Minimize damage to your work surfaces with these brass punches, which are softer than steel punches.

Contains pin-loosening, pin-removal, and center-marking punches as well as chisels.

Punch a hole in your material to prepare for the installation of fabric grommets. Strike these tools with a mallet.

These punches set grommets that have an extended-neck tooth lock washer.

Line up holes by driving these pins through existing rivet, pin, and bolt holes in multiple pieces of metal. Alternatively known as lineup taper punches.

These brass tools reduce marring on metal surfaces because they're softer than steel punches.

Made from aluminum-bronze that is Factory Mutual approved, these nonmagnetic, corrosion-resistant tools inhibit sparking. They satisfy OSHA requirements for nonsparking tools.

Set nails flush or drive them out of view without damaging wood surfaces.

Punch soft materials and scribe lines in metal and wood.

With an internal spring mechanism, these punches offer one-hand operation when marking hole centers.

Punch has two viewing lenses. One has a circle and dot and one has a crosshair to enable you to pinpoint the location where you need to punch. Replace the lens with one of the two included punches and strike it with a hammer to mark the hole center.

Strike these Starrett punches with a hammer to mark hole centers in metal and other materials. Also known as center punches.

Also known as center punches, strike these with a hammer to mark hole centers in metal and other materials.

These sets come with three punches for use with a variety of hole sizes. Insert one into an existing hole and twist the handle to open the end of the punch. The point automatically centers once the punch has fit the hole size.

Fit the punches in these sets through existing holes and mark the center of the hole in a second workpiece.

Also known as blind-hole spotters, the punches in these sets fit into closed-end holes and mark the center of a complementary hole.

Also known as blind-hole spotters, these punches fit into closed-end holes and mark the center of a complementary hole.

Also known as transfer screws, these punches have a uniform shoulder height so you can quickly transfer multiple hole locations at once.

Also known as transfer screws, these punches have a uniform shoulder height so you can quickly transfer multiple hole locations at once.

Also known as 40-ton metalworkers, these hydraulic machines handle a variety of forming tasks including pressing, punching, notching, and shearing.

Create a raised edge in sheet metal that locks into the rolled edge of another piece.

The jaws have V-notches in 1/4" increments to measure the depth of bends.

Offset handles allow you to use these tools in tight spaces.

Choose only the characters you need to make your message from 0-9, A-Z, period, forward slash (/), dash, and blank spaces.

Everything you need to make your own messages in one convenient case, including letters, numbers, punctuation, and a holder.

These stamps provide an entire number set in the convenience of one handheld stamp. Rotate the wheel to change the character.

The thick shank provides more control and consistent marks than our standard metal stamps. Make marks on surfaces with a Rockwell hardness up to C30, including leather, wood, and most metals. Stamps are steel.

Made from 440C stainless steel, these stamps won't rust and flake with exposure to moisture and chemicals. They're strong enough to make marks on surfaces with a Rockwell hardness up to C50, including other stainless steels and heat-treated steel.

These stamps have a border around the characters to help them stand out.

These stamps have a solid face.