We will reply to your message within an hour.
Turn the dial to control the percentage of time that these heaters cycle on, from 5% to 100%. Commonly used to thaw pipes, prevent valves from freezing, and heat beakers and flasks in labs, they're good for temporary and occasional use where rapid heating is required but precise temperature control is not.
The thermostat automatically turns these heaters on when the temperature drops below 38° F and turns them off when the temperature reaches 45° F.
These heaters require a separate temperature switch or controller to regulate heat output.
Wrap the flexible fiber heating element around small-diameter pipes and tubes or pack it into tight spaces.
There’s no need for power-connection kits with these finished lengths of cable.
These heaters require a power-connection kit.
For demanding applications such as hot-melt transfer pipes, these heaters have a maximum heat output of 1400° F.
Rated for a maximum heat output of 900° F, these heaters are often used for thawing frozen pipes and rapid spot heating.
An adjustable thermostat senses the container’s surface temperature to automatically control heat output.
For more durability than other adhesive-mount heaters, a thick layer of fiberglass-reinforced silicone rubber encases the heating element.
Also known as foil heaters, these bend around corners and edges without causing damage to the heating element.
These heaters are rated for environments where hazardous material is present.
Use this slippery PTFE-coated tape for a smooth release on heat sealers and molds.
Fiberglass is laminated with Teflon® PTFE for a slippery, durable tape with excellent chemical and temperature resistance. Use it as a release surface on heat sealers and blister forming equipment.
This tape discharges minor amounts of surface static electricity and resists static buildup.
Also known as skived tape, this low-friction tape stretches to conform to irregular surfaces.
A strong, thick layer of Teflon® PTFE makes this tape tougher than standard Low-Friction Tape Made with Teflon® PTFE.
Our most slippery tape, the slick surface allows items to glide smoothly over it.
This tape provides a slick surface along with excellent resistance to electrical current.
Low-Friction Tape Shapes Made with Teflon® PTFE.
Highly resistant to impact, tearing, and corrosive chemicals, use FEP tape to line chutes and hoppers and to cover shelves in laboratories.
PEEK offers the best wear and abrasion resistance of our low-friction tapes. Use it for wire wraps and sliding bearing surfaces.
Often referred to as Rulon and bearing tape, this self-lubricating PTFE tape provides better abrasion and wear resistance than our standard slippery PTFE tape.
Also known as roller tape, this tape is coated with silicone to grip smooth surfaces and resist sticky substances, such as ink. It adheres to itself without adhesive.
Made of polyester plastic, this tape resists tearing in high-temperature masking jobs, such as on circuit boards and when powder coating.
Cover holes, fastener heads, and small areas with these shapes.
Aluminum foil is laminated to a tough fiberglass cloth to form a high-strength, reflective tape that resists temperatures up to 500° F. Use it for flame-spray masking and wire harness heat shielding.
In addition to handling temperatures up to 500° F, this fiberglass tape is tough enough for abrasive applications such as sand blasting.
Protect screen-printed graphics during high-temperature laminating and molding.
Cover small spots and holes while paint stripping and electroplating, or use as a moisture and dust barrier. These aluminum foil discs are flexible and conform to irregular shapes.
This crepe paper tape keeps its hold, even on 300° F surfaces.
Use this tape to wrap and splice cables, mask components while soldering, or as a 3D printing surface.
Use these convenient cut shapes to mask holes, fastener heads, and small areas while soldering.
At half the thickness of our other masking tape for electronics, this polyimide tape conforms easily to components.
This tape reflects intense heat to protect sensitive components.
Made from stainless steel, this noncorrosive, nonstaining, and nonmagnetic tape bonds to metal. Patch scratched coatings and finishes to prevent corrosion in marine, food-processing, and nuclear applications.
Seal out light to mask LEDs and prevent backlight bleed on LCD monitors with this opaque polyester tape.
Protect impact-prone surfaces from scratches, chips, and abrasion with this thick, conformable tape.
Easy to apply and remove, this film tape protects touch screens and other delicate parts during manufacturing and shipping.
Made with fiberglass for durability and abrasion resistance, this tape also withstands high temperatures.
No need for adhesive—this tape fuses to itself for a permanent seal and stretches to fit virtually any form. Also known as cold shrink tape.
This chemical-resistant tape has adhesive on both sides.
At only 0.0025" thick, this tape combines conformability with durability and abrasion resistance.
Apply this liquid for a skin-tight protective coating that insulates and resists moisture, acids, and corrosion.
Use this tape to attach components to heat sinks and metal chassis walls in place of screws and other mechanical fasteners. It conducts heat away from sensitive electronics.
Quickly conduct heat away from electronic components. Kapton® polyimide gives this tape excellent electrical isolation.
Twice as thick as our standard antistatic electrical tape, this tape is made of abrasion-resistant aramid and antistatic PTFE.
Use this tape to modify printed circuit boards, shield components, and prototype wiring-board layout and design.
This polyester tape has a woven mesh edge that conducts electricity. Use it to shield cables and electronic components from EMI (electromagnetic interference).
A coating on this polyimide tape minimizes ESD (electrostatic discharge) when unwound from the roll and also during removal.
The adhesive on this conformable aluminum foil tape is electrically conductive for use on surfaces that can't be soldered. Use it to shield cables and electronic components from EMI (electromagnetic interference).
Prevent the spread of fire while sealing, cushioning, and damping vibration. This tape has adhesive on both sides.
Use this transparent tape for laminating, splicing, and mounting, even on hard-to-bond plastics. It has adhesive on both sides.
With a higher level of clarity than standard tape, this tape is good for joining layers of material that need light to pass through, such as clear plastic and glass.
Cut these sheets to create a customized, permanent bond in the shape you need.
This tape can withstand temperatures up to 300° F.
Seal foil-jacketed insulation as well as air-conditioning and refrigeration systems with this conformable aluminum tape.
Reinforced with fiberglass, this tape is flexible yet resists tearing. Use it for sealing and patching insulation and duct.
Seal fiberglass duct and insulation that's faced with an all-service jacket (ASJ). Tape is reinforced with fiberglass.
For easy identification, this tape is printed with flexible duct standard UL 181A-P or UL 181B-FX.
When exposed to moisture, this resin-coated fiberglass tape becomes rock-hard in about 30 minutes. Use it for rigid, waterproof repairs.
Wrap this tape around carbon fiber and other composite parts, then heat to 150° F. Tape shrinks to squeeze out air bubbles and apply pressure so parts cure without voids.
Patch and connect tarps with this thick, woven plastic tape.
Often used to repair vinyl facings, this tape can be used on water heater blankets and fiberglass insulation joints.
Use this glossy tape to seal seams and repair vinyl material such as banners.
Use this flame-retardant tape for sealing in galleys and other harsh, wet environments.
Temporarily join rolls of paper and film—this tape won't leave residue behind.
Only 0.0019" thick, so spliced film and paper easily pass through machinery without breaking.
A mica and silicone rubber blend allows this sleeving to withstand temperatures up to 2100° F. It can be quickly applied to hose or cable like tape, so it's a good option for emergency patches.
Stick this flexible tape to the back of welding seams to contain spatter and prevent oxygen, water vapor, and other gases from weakening the weld.
For welding large gaps, these strips form a rigid mold for your weld.
This label tape works with Dyno Rhino model printers.
Tape works with Epson label printers.
This label tape works in Brady M710 printers.
Create labels for cable and wire using your Brady BMP41, BMP51, BMP53, or M511 printer.
Refill the tape in your Brady BMP21 label printer.
Wrap this tape tightly around pipe and other surfaces to seal cracks and joints without having to shut down your system.