Thick leaves and a large diameter pin make these hinges good for use with heavy doors. Bearings allow these hinges to open and close heavy doors smoothly. The hinges are load rated; capacity is based on two hinges per door. All have a nonremovable pin to deter tampering.

304 stainless steel hinges are more corrosion resistant than primed carbon steel. They also have good chemical resistance.

For technical drawings and 3-D models, click on a part number.

Turn a set screw to adjust the door 1/8" up or down after it's hung. Thick leaves and a large diameter pin make these hinges good for use with heavy doors. Bearings allow the hinges to open and close heavy doors smoothly. The hinges are load rated; capacity is based on two hinges per door. All have a nonremovable pin to deter tampering. To choose a door mounting location, stand on the push side of the door—use a right-side hinge if the hinge is on the right or a left-side hinge if it’s on the left.

304 stainless steel hinges are more corrosion resistant than primed low-carbon steel. They also have good chemical resistance.

For technical drawings and 3-D models, click on a part number.

Tighten or loosen an adjustment screw to change the hinge resistance. Constant resistance through the full range of motion holds lids, panels, and doors at any angle. These hinges discourage tampering, since they can’t be taken apart without damaging the hinge. Capacity is based on one hinge per door.

Plastic hinges are a lightweight alternative to metal hinges.

Stainless steel hinges are stronger and more corrosion resistant than plastic hinges.

For technical drawings and 3-D models, click on a part number.

One leaf mounts around the edge of the door for a secure hold, while the other mounts to the frame. Longer than other entry door hinges, this piano-style hinge runs the entire length of doors for strength and durability. Bearings allow the hinge to open and close doors smoothly. A nonremovable pin deters tampering. Capacity is based on a maximum door size of 4' Wd. × 7' Ht. Cut hinge to size with a hacksaw.

For technical drawings and 3-D models, click on a part number.

A snap-on cover protects these hinges from tampering and creates a finished appearance. Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability. Capacity is based on a maximum door size of 4' Wd. × 7' Ht.

For technical drawings and 3-D models, click on a part number.

Longer than other entry door hinges, these piano-style hinges run the entire length of doors for strength and durability. Bearings allow the hinges to open and close doors smoothly. All hinges have a nonremovable pin to deter tampering. Capacity is based on a maximum door size of 4' Wd. × 7' Ht. Cut hinges to size with a hacksaw.

304 stainless steel hinges are more corrosion resistant than zinc-plated low-carbon steel. They also have good chemical resistance.

For technical drawings and 3-D models, click on a part number.

With large pin diameters for added strength, these hinges can hold heavier doors and gates than other strap hinges. Hinges with a nonremovable pin deter tampering. Style 3 capacity is based on three hinges per door with the maximum door size listed. Style 4 capacity is based on four hinges per door with the maximum door size listed.

For technical drawings and 3-D models, click on a part number.

These hinges have wide hinge leaves that provide a large mounting surface to keep doors and gates from sagging. All have a nonremovable pin to deter tampering. Style 1 capacity is based on one hinge per door.

Galvanized low-carbon steel hinges have better corrosion resistance than zinc-plated low-carbon steel.

For technical drawings and 3-D models, click on a part number.

This hinge has wide hinge leaves that provide a large mounting surface to keep trailer doors from sagging. It also has an offset leaf to accommodate a door seal. Offset is the space between the door face and the frame when the door is closed.

For technical drawings and 3-D models, click on a part number.

The hinge pin attaches to the frame leaf so you can quickly lift the door off the hinge without removing the pin. These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging. All are self-lubricating for smooth operation. They can be mounted on the left or right side of the door. To switch from left- to right-hand orientation, remove the pin from the frame leaf and turn the leaf 180°, then reinsert the pin. The pin is secured with a cap. Capacity is based on two hinges per door.

Offset-leaf style hinges can accommodate a door seal. Offset is the space between the door face and the frame when the door is closed.

For technical drawings and 3-D models, click on a part number.

These hinges have wide hinge leaves that provide a large mounting surface to keep freezer and refrigerator doors from sagging. Offset-leaf style hinges can accommodate a door seal. Offset is the space between the door face and the frame when the door is closed. Styles 3 and 4 capacity is based on two hinges per door.

Chrome-plated zinc hinges have better corrosion resistance than painted zinc.

For technical drawings and 3-D models, click on a part number.