Body Material Body Material |
|---|
|
For Drill Bit Size Decimal Equivalent For Drill Bit SizeDecimal Equivalent |
|---|
|
|
Overall Length When Clamped Overall LengthWhen Clamped |
|---|
|
|
|
Overall Length Overall Length |
|---|
|
|
|
Handle Material Handle Material |
|---|
|
Component Component |
|---|
|
Hole-Grip Clamps
Insert these clamps into drilled holes in sheet material to grip and align while riveting or welding. They require clamp installation pliers (sold separately) for positioning and removal.
| OD | For Drill Bit Size | For Material Thickness | Overall Lg. | Body Material | Each | |
| 3/32" | No. 40 | 0"-1/4" | 2 1/4" | Steel | 0000000 | 00000 |
| 1/8" | No. 30 | 0"-1/4" | 2 1/4" | Steel | 0000000 | 0000 |
| 5/32" | No. 20 | 0"-1/4" | 2 1/4" | Steel | 0000000 | 0000 |
| 3/16" | No. 10 | 0"-1/4" | 2 1/4" | Steel | 0000000 | 0000 |
| 1/4" | 1/4" | 0"-1/4" | 2 1/4" | Steel | 0000000 | 0000 |
| 7 1/4" Lg. Steel Clamp Installation Pliers | 0000000 | 000000 |
Hole-Mount Push/Pull Toggle Clamps
Panel mount through a hole with the included nut, or drill and tap a hole to flush mount. A pushing or pulling motion holds workpieces from the side. These clamps secure in two positions—when the plunger is fully extended and when the plunger is fully retracted. The plunger is internally threaded to accommodate threaded holding screws and other threaded fixtures (not included).
Stainless steel clamps have good corrosion resistance.
For technical drawings and 3-D models, click on a part number.
Plunger | When Clamped | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Holding Capacity, lbs. | Lg. | Travel | Dia. | Thread Size | Thread Lg. | O'all Ht. | O'all Lg. | Includes | Each | |
Steel | ||||||||||
| 200 | 1" | 3/4" | 3/8" | 1/4"-20 | 5/8" | 3 1/8" | 2 5/8" | Mounting Nut | 0000000 | 000000 |
| 300 | 1 7/8" | 1 1/2" | 7/16" | 5/16"-18 | 1" | 4 1/4" | 5" | Mounting Nut | 0000000 | 00000 |
| 450 | 1 7/8" | 1 1/2" | 1/2" | 5/16"-18 | 1" | 4 1/4" | 5 5/8" | Mounting Nut | 0000000 | 00000 |
| 700 | 3 1/4" | 2 5/8" | 5/8" | 3/8"-16 | 1 1/4" | 5 5/8" | 6 3/4" | Mounting Nut | 0000000 | 00000 |
18-8 Stainless Steel | ||||||||||
| 200 | 1" | 3/4" | 3/8" | 1/4"-20 | 5/8" | 3 1/8" | 2 5/8" | Mounting Nut | 0000000 | 00000 |
| 300 | 1 7/8" | 1 1/2" | 7/16" | 5/16"-18 | 1" | 4 1/4" | 5" | Mounting Nut | 0000000 | 00000 |
| 700 | 3 1/4" | 2 5/8" | 5/8" | 3/8"-16 | 1 1/4" | 5 5/8" | 6 3/4" | Mounting Nut | 0000000 | 000000 |
Plunger | When Clamped | |||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Holding Capacity, lbs. | Lg. | Travel | Dia. | Thread Size | Thread Lg. | O'all Ht. | O'all Lg. | Includes | Each | |
Steel | ||||||||||
| 200 | 1" | 3/4" | 3/8" | M6 | 15 mm | 3 1/8" | 2 5/8" | Mounting Nut | 0000000 | 000000 |
| 300 | 2 3/16" | 1 1/2" | 7/16" | M8 | 25 mm | 4 3/16" | 4 1/4" | Mounting Nut | 0000000 | 00000 |
| 700 | 3 5/8" | 2 5/8" | 5/8" | M10 | 31 mm | 5 5/8" | 6 11/16" | Mounting Nut | 0000000 | 00000 |
18-8 Stainless Steel | ||||||||||
| 200 | 1 5/16" | 3/4" | 3/8" | M6 | 16 mm | 3 1/8" | 2 7/16" | Mounting Nut | 0000000 | 00000 |
| 400 | 2 3/16" | 1 1/2" | 7/16" | M8 | 25 mm | 4 3/16" | 4 1/4" | Mounting Nut | 0000000 | 00000 |
Hole-Mount Push/Pull Toggle Clamps with Locking Handle
Push the lever to lock the handle and prevent accidental opening. Panel mount these clamps through a hole with the included nut, or drill and tap a hole to flush mount. They have an internally threaded plunger to accommodate threaded holding screws and other threaded fixtures (not included).
Push/pull clamps secure in two positions—when the plunger is fully extended and when the plunger is fully retracted.
Pull-only clamps secure when the plunger is fully retracted.
For technical drawings and 3-D models, click on a part number.
Hole-Mount Adjustable-Travel Push/Pull Clamps
Drill a hole to mount these clamps through a surface and secure the mounting flange with screws. The plunger can be locked at any position along its travel. Push the plunger forward until it contacts the workpiece and then rotate the lever handle to clamp a workpiece from the side. The plunger is internally threaded to accommodate threaded holding screws and other threaded fixtures (not included).
For technical drawings and 3-D models, click on a part number.
Plunger | When Clamped | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Holding Capacity, lbs. | Lg. | Ht. | Travel | Dia. | Thread Size | Thread Lg. | O'all Ht. | O'all Lg. | Body Material | Each | |
| 600 | 7 7/8" | 7/8" | 7 7/8" | 1/2" | M6 | 12 mm | 5 1/8" | 13" | Steel | 0000000 | 0000000 |
Hole-Grip Clamp Sets
Sets include clamps and installation pliers. Insert clamps into drilled holes in sheet material to grip and align while riveting or soldering.
| Number of Pieces | Includes | Container Type | Each | |
| 7 | One 2 1/4" Lg. 3/32" OD Steel Hole-Grip Clamp with 1/4" Max. Opening (For No. 40 drill bit size) One 2 1/4" Lg. 1/8" OD Steel Hole-Grip Clamp with 1/4" Max. Opening (For No. 30 drill bit size) One 2 1/4" Lg. 3/16" OD Steel Hole-Grip Clamp with 1/4" Max. Opening (For No. 10 drill bit size) One 2 1/4" Lg. 1/4" OD Steel Hole-Grip Clamp with 1/4" Max. Opening (For 1/4" drill bit size) Two 2 1/8" Lg. Pliers-Activated Spring Clamps with 1/2" Max. Jaw Opening and Aluminum Jaws 7 1/4" Lg. Steel Clamp Installation Pliers | Plastic Case | 0000000 | 000000 |
| 51 | Ten 2 1/4" Lg. 3/32" OD Steel Hole-Grip Clamps with 1/4" Max. Opening (For No. 40 drill bit size) Ten 2 1/4" Lg. 1/8" OD Steel Hole-Grip Clamps with 1/4" Max. Opening (For No. 30 drill bit size) Ten 2 1/4" Lg. 5/32" OD Steel Hole-Grip Clamps with 1/4" Max. Opening (For No. 20 drill bit size) Ten 2 1/4" Lg. 3/16" OD Steel Hole-Grip Clamps with 1/4" Max. Opening (For No. 10 drill bit size) Ten 2 1/4" Lg. 1/4" OD Steel Hole-Grip Clamps with 1/4" Max. Opening (For 1/4" drill bit size) 7 1/4" Lg. Steel Clamp Installation Pliers | Plastic Case | 0000000 | 00000 |
Screw Clamps
The spring-loaded tips on these clamps swivel in all directions to make maximum contact with angled and uneven workpieces. Install by removing the tip, threading the screw through the mounting base’s hole, and reattaching the tip on the other side. Use mounting bases to attach screw clamps to flat surfaces. Their threaded portion is machined at a slightly downward angle so the clamp can get a strong grip on the workpiece. Length is measured from under the screw collar.
Optional extra-large steel tips offer more gripping strength. Optional nonmarring plastic tips minimize damage to workpieces.
Clamps | |||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Tip | Handle | Optional Extra-Large Steel Tips | Optional Nonmarring Plastic Tips | Replacement Retaining Springs | |||||||||||
| Thread Size | Lg. | Dia. | Lg. | Ht. | Wd. | Max. Swivel Angle | Material | Each | Each | Each | Each | ||||
| 1/4"-20 | 1 1/4" | 3/8" | 1/4" | 5/8" | 1 1/8" | 10° | Steel | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 | 000000000 | 00000 |
| 1/4"-20 | 2 3/4" | 3/8" | 1/4" | 5/8" | 1 1/8" | 10° | Steel | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 1/4"-20 | 3 1/2" | 3/8" | 1/4" | 5/8" | 1 1/8" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 3/8"-16 | 1 5/16" | 1/2" | 1/4" | 1" | 2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 3/8"-16 | 2 13/16" | 1/2" | 1/4" | 1" | 2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 3/8"-16 | 4 5/16" | 1/2" | 1/4" | 1" | 2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 1/2"-13 | 2 1/16" | 5/8" | 3/8" | 1 1/8" | 2 1/2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 1/2"-13 | 3 9/16" | 5/8" | 3/8" | 1 1/8" | 2 1/2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 1/2"-13 | 5 1/16" | 5/8" | 3/8" | 1 1/8" | 2 1/2" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 5/8"-11 | 2 5/16" | 3/4" | 1/2" | 1 1/4" | 3" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 5/8"-11 | 3 13/16" | 3/4" | 1/2" | 1 1/4" | 3" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
| 5/8"-11 | 5 5/16" | 3/4" | 1/2" | 1 1/4" | 3" | 10° | Steel | 000000000 | 00000 | 000000000 | 0000 | 000000000 | 0000 | 000000000 | 000 |
Hole-Mount Screw Clamps
Also known as press screws, mount these clamps through a drilled hole and turn the crank to move the jaw end of the screw in and out.
Jaw | Handle | Overall | Mounting Holes | ||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| Screw Lg. | For Hole Size | Lg. | Wd. | Screw Material | Style | Material | Lg. | Wd. | Number of | Dia. | Mounting Fasteners Included | Each | |
| 9" | 1" | 1 3/8" | 1 3/8" | Steel | Crank | 18-8 Stainless Steel | 12" | 6" | 4 | 1/8" | No | 0000000 | 000000 |
| 12" | 1" | 1 3/8" | 1 3/8" | Steel | Crank | 18-8 Stainless Steel | 14 1/2" | 6" | 4 | 1/8" | No | 0000000 | 00000 |
| 18" | 1" | 1 3/8" | 1 3/8" | Steel | Crank | 18-8 Stainless Steel | 20 1/2" | 6" | 4 | 1/8" | No | 0000000 | 00000 |
Revolving Screw Clamps
When loosened, you can spin the body of this clamp around its mounting point for better access to the workpiece. Position over your workpiece and turn the handle to clamp down. Mount the clamp in a threaded hole or on a mounting base (sold separately).
Bench-Mount Locking Plier Clamps
Clamp a workpiece down against your bench top. Turn the knob to adjust the opening size; squeeze the handles to lock the clamp in place. Press the lever to release.
| Max. Clamping Clearance | Reach | Holding Capacity | Overall Lg. | Lock Release | Body Material | No. of Mounting Holes (Diameter) | Mounting Fasteners Included | Each | |
Pivoting Jaw | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| 4" | 3 1/4" | Not Rated | 12" | Lever | Steel | 1 (1/2") 4 (5/16") | No | 0000000 | 000000 |