For light duty spray-down applications, attach these wash guns to any standard garden hose.

These wash guns have a high maximum pressure, so use them with pressure washers and high-pressure spray systems.

Connect these guns to your garden hose and automatically dispense solution from the attached bottle instead of dragging around a siphon hose.

Use these guns to clean as well as apply chemicals and solvents.

Connect these cleaners to existing steam lines to remove dirt, grease, and heavy oils from most surfaces.

Twist the barrel to adjust water flow.

Use the lever to turn water flow on and off.

Control the flow while dispensing diesel fuel with these nozzles.

Nozzles allow you to control the flow while dispensing hydraulic fluid.

Connect these swivels to the threaded end of your dispensing hose. They rotate before and after installation as needed to prevent hose from twisting, kinking, and wearing prematurely.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Use with Loc-Line hose to assemble and disassemble components.

Draw coolant from your existing tank.

Draw coolant from your existing tank.

Press the lever to stop coolant mist and start a high-velocity air stream to remove dust and shavings.

These nozzles handle coolant pressure up to 150 psi.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.

For high-pressure coolant lines, these nozzles withstand pressure up to 500 psi.

Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.

Attach to your blowgun to direct airflow.

Extend these telescoping nozzles to increase your reach.

Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.

These nozzles are made of FDA-listed materials.

The magnetic base mounts to your work surface and has a control valve for adjusting airflow.

Nozzles are attached to a flexible tube or hose that bends and holds its shape until you reposition it.

Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.

These nozzles produce a flat, thin spray pattern. They're good for general cleaning, washing, etching, foam control, and applying coatings.

Drill a hole anywhere along a pipe and snap on these nozzles. Spray tips can be quickly and easily removed for cleaning and replacement.

Spray is deflected at a narrow angle to create the highest impact of all our flat spray nozzles.

Quickly change spray angles by removing the nozzle and snapping on a new one.

With a unique spiral design, these nozzles produce high flow rates and are clog-resistant.

These nozzles project their spray at a right angle from their threaded connection.

The large square coverage area makes these nozzles a good choice for chemical processing as well as for cooling applications.

These nozzles produce a flat, thin spray pattern.

No need to juggle multiple nozzles with different spray angles—just turn the cover to adjust the spray angle from 0° to 80°.

Push the nozzle out for lower pressures and pull it back for higher pressures. Turn the cover to adjust the spray angle from 0° to 25° or 75°.

No need to switch between nozzles—push these nozzles in and pull them out to change their pressure level, and twist their cover to adjust the spray angle between 0° and 40°. Their quick-disconnect hose connection makes attaching and removing them easy.

Instead of swapping between nozzles, turn the cover on these nozzles to change their spray angle. They have quick-disconnect couplings for easy detachment.

A wide spray angle provides a larger coverage area and produces a finer, more atomized spray than full-cone nozzles.

Fogging nozzles provide smaller, more atomized spray droplets than misting nozzles.

A wide spray angle provides a larger coverage area and produces a finer, more atomized spray than full-cone nozzles.

Create small, atomized spray droplets for cooling, moistening, and humidifying applications. These nozzles have a check valve that prevents dripping when they’re turned off

These nozzles produce a concentrated stream for more effective cleaning than stationary nozzles.

Certified by 3-A to meet sanitary design standards, these stationary nozzles have a 360° spray pattern to effectively rinse tanks and vessels in food, beverage, and pharmaceutical environments.