Though not as bright as our miniature fiber-optic lights, these lights have built-in LEDs that last longer, are more efficient, and are more affordable.

Faster and easier to reposition than articulating-arm lights, these gooseneck-arm lights attach to your workspace for additional lighting.

These lights have a longer reach and hold their position better than gooseneck-arm lights, especially around vibration.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

Hang these lights where you need them on the job site.

A flexible design allows these lights to be suspended above, wrapped around, or routed through areas on the job site.

Use sun energy to bring light to remote areas and storage spaces without electrical wiring. These lights come with a solar panel to recharge their battery.

Bring light to areas that don't have electrical power service.

Use these with portable lights that use screw-in bulbs.

These IP67 rated lights withstand temporary submersion in a maximum of one meter of water for up to 30 minutes. They're compact for easy transport to job sites with no electrical power.

The handle on this floodlight also acts as a stand—pivot it 360° to aim light where it's needed. This floodlight is small and easy to carry to job sites that don't have electrical power.

The gooseneck arm on these lights allows you to direct light exactly where it's needed. They have a reflector that distributes light more evenly than other portable lights.

Also known as jelly jar lights. These fixtures have a guard that protects the lens from breaking.

Mount these lights flush with ceilings in wet locations—all are sealed to keep out humidity and dripping, splashing, and falling liquids. Unlike recessed can lights, which require a separate housing, these fit directly into a cutout in your ceiling and are held in place by springs.

With a lower profile than other bay lights, linear bay lights mount closer to ceilings, providing more room for racks or shelving.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

Update standard outlet boxes in closets, hallways, and storage rooms to use LED light.

These lights fit into ceiling cutouts.

Mount these fixtures where you need light but don't have an electrical connection. They automatically turn on when movement is detected and off when an area is unoccupied.

No need for wiring—these lights plug-in with a two-prong plug. Also known as shop lights.

Also known as turret lights, these fixtures have uplight or downlight reflectors to direct light.

Also known as strip or channel lights, the ends of these fixtures are designed to be wired together to create long rows of lights.

Designed to withstand heat and grease, these lights are often used in commercial cooking hoods. They are also known as hood lights.

Mount lights in recessed spaces so the lens is flush with the wall.

These LED lights have an air-tight seal to protect against contaminants.

A sealed lens keeps moisture out to protect these lights against washdowns.

Compared to other dock lights that can only adjust vertically and horizontally, these lights bend at any angle to direct light exactly where it's needed.

Attach these tiny flashlights to a grease gun nozzle or air hose to shine light directly onto your work.

Direct light where it’s needed with these pivoting-head flashlights. When plugged in, they’ll automatically light up if the power goes out.

Shine light into hard-to-reach spaces with these flexible-arm flashlights.

The handle opens into a tripod, so you can shine light on your work while keeping your hands free.

Always have a flashlight on hand—these attach to a key ring.

Because these flashlights are buoyant, they're easy to recover when dropped in the water.

Extend light into hard-to-reach spaces by attaching a fiber-optic cable to your flashlight.

Similar to a holster without the bulk, belt loops hold your flashlight when not in use.

Convert incandescent, halogen, krypton, and xenon Maglite flashlights into LED flashlights to produce more light and consume less battery power.

In addition to pivoting 210°, the light heads rotate 360° for directing light exactly where it’s needed. They're rated for use in environments where hazardous material is present.

Attach to your key ring or hat so you’ll always have a flashlight on hand. They're rated for use in environments where hazardous material is present.

Safe for use in environments where hazardous material is present.

Turn a mini flashlight into a headlamp with these straps.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

Mount these lights near entry doors, loading areas, and driveways to cast an even glow of light.

No need for wiring—these lights plug-in with a three-prong plug.

Heads adjust to any angle so you can direct light where needed.

These lights automatically turn on when movement is detected and off when an area is unoccupied.

Gently bend these single-use lightsticks to activate.

Communicate a status at a glance by wiring these strip lights to change color when a part is malfunctioning inside your enclosure.

With a slimmer profile than other strip machine lights, these lights fit in tight spots on workspaces and inside machinery because they don’t have a circuit board.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

Update conventional fluorescent tubular lights with newer LED technology. These lights are furnished with brackets that have the same hole pattern as most older lights for easy changeover.

Suspend these lights overhead or mount them above your workspace.

Rated NEMA 4X, these lights are protected from corrosion and washdowns.

Rated for use in damp locations, these lights withstand humidity and moisture.