Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Update conventional fluorescent tubular lights with newer LED technology. These lights match the diameter of most older lights and fit existing brackets without the need to drill new mounting holes.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

Suspend these lights overhead or mount them above your workspace.

Brighten countertops that your ceiling lights can’t reach. These lights are low-profile, so they won’t take up valuable workspace below your cabinets.

These lights cast a narrower beam than other gooseneck-arm machine lights. Reposition them faster and more easily than articulating-arm lights.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

These lights cast a narrow beam of light. With a gooseneck arm, they are faster and easier to reposition than articulating-arm lights.

Stretch the arm to bring light directly over your work—even across a large surface. Also known as articulating arm lights, these lights have rigid sections that hold their position steady, including when fully extended.

Clip or clamp these lights near your work to illuminate what you’re working on without lighting up the whole room. Powered by a rechargeable battery, they’re often used in spaces where an outlet isn’t available.

Though not as bright as our miniature fiber-optic lights, these lights are more affordable. With flexible arms, you can adjust these lights to direct light where you need it, even in hard-to-reach spots.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Hang these lights above your workspace—they shine through long tubes to distribute even light with minimal glare and shadows. Carry them where you need them and suspend them from pipes, beams, and other overhead surfaces.

Hang these lights where you need them on the job site.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Point light where it’s needed—even in wet areas. These lights are sealed against splashing and dripping water.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Splashes and drips are no problem for these lights. They don’t need an outlet, so you can bring them wherever you need them.

Aim light where you need it—even in explosion-prone spaces—by raising, lowering, and tilting these lights on their tripod. Rated NEC Classes I, II, III, and Zone 0, they’re safe to use near ignitable concentrations of flammable or combustible gas, dust, or fibers.

Bring light to explosion-prone work areas. Rated NEC Class I, these lights are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

With a rounded, weighted base, these floodlights wobble—but don't fall over—when bumped.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten remote areas using the same battery as your other cordless Milwaukee tools.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

Our brightest plug-in floodlights, these lights illuminate large worksites—about the size of a hockey rink.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

Brighten enclosures and small spaces like closets and drawers—no hardwiring or outlets needed. Powered by a rechargeable battery, these lights are easy to install and help save on maintenance costs.

Illuminate your electronics cabinets and racks with long-lasting LED lights.

Clip these headlamps right into a mount on your tactical or rescue helmet.

Light up work while staying visible in high-risk areas. These headlamps have LEDs on the head band so forklift and truck drivers can see you.

Light up work without risking an explosion. NEC rated, these headlamps are safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, and liquids.

Drop these headlamps in water and they’ll still work—they’re IP rated to withstand submersion for at least 30 minutes.

No bigger than a roll of tape, these lights fit inside equipment to provide visibility during tool changeovers and maintenance.

Mount these lights horizontally or vertically in places where a tower will not fit.

Use these lights in tight spaces in place of a tower. They emit three colors from a single lens.

The quick-connect four-pole M12 plug on these lights makes them easy to hook up and configure.

These lights have LED bulbs for years of maintenance-free operation and can be wired as either continuous or flashing.

Use a computer to program colors, lighting patterns, and sounds to communicate a variety of status conditions, material levels, and cycle times—these stack lights have 21 colors and 11 sounds.

These lights are rated IP69K to withstand high-pressure washdowns, such as those in food and beverage applications.

Make a custom panel light with your choice of light and lens cap color.

The most versatile of our machine vision lights, these bar lights can be used alone, installed side-by-side, or assembled into a ring light.

Surround your camera with light for perfectly aligned brightness. These small and lightweight ring lights are mounted directly around your machine vision camera or vision sensor.

Detect edges, take measurements, and spot holes with your machine vision camera by passing objects over these backlights.

Use these as replacement bulbs in stack lights.