Upgrade your fluorescent recessed lighting to energy-efficient LEDs without removing fixtures and exposing insulation. No need for a permit—these lights don't require opening the space above the ceiling. They connect to standard housings with the included springs and cables. Just remove the old lens, bulbs, drivers, and their wiring before installation. DLC (DesignLight Consortium) listed, these lights have been tested to confirm their energy efficiency. They’re also ETL listed for use in damp locations.

Adjust the light appearance and brightness to match your existing lighting. The frosted lens disperses light evenly to prevent glare on equipment.

For technical drawings and 3-D models, click on a part number.

These fixtures disperse light from the sides as well as the bottom to produce ambient lighting ideal for indoor spaces such as offices and storage rooms. Rated for use in damp locations, these lights withstand humidity and moisture. All have a lens that disperses light evenly. Lights can be hardwired to operate on any of the voltages listed.

Those with a neutral light appearance emit a neutral white light often found in workspaces. Others with a neutral and cool light appearance have a selectable light appearance so they can emit neutral or cool light.

Add suspension hardware (sold separately) to hang lights from the ceiling. Suspension hardware for style A includes two wire rope slings with hooks and two wire rope clamps. No tools required—adjust the length and tighten clamps to secure. Suspension hardware for style B includes a mounting plate, an adjustable cable assembly, and a feed cord with three wire leads.

For technical drawings and 3-D models, click on a part number.

Brighten high-traffic areas with our most rugged ceiling lights. Rated IK10, the highest impact resistance rating, they’re protected by a 16-gauge cold-rolled steel frame and polycarbonate lens. A good choice for public spaces such as parking garages and stairwells, the lens is secured with tamper-resistant Torx screws to prevent vandalism. They have a center pin that makes them difficult to remove without special tools. The lens disperses light from the sides and bottom for ambient lighting.

Install these lights in covered areas indoors or outdoors—UL listed for wet locations, they’re sealed against humidity and dripping, splashing, and falling liquids.

Powered by the sun, these lights illuminate outbuildings, shipping containers, and other remote places that lack electricity. They also store up to 12 hrs. of runtime that can be split over several days, so they brighten spaces even on cloudy days and at night. And don't worry about accidentally leaving the lights on and draining the battery—a timer switch turns them off after a set period of time, up to 2 hrs. To maximize battery runtime, these lights use energy-efficient LEDs. They cast a neutral white light that's found in most workspaces and make colors appear natural and vibrant. IP65 rated, they’re dust tight and can handle sprays of water such as those from a garden hose. This means wind, rain, and snow won’t be a problem.

They include all you’ll need to install them: a solar panel, battery, lights, and a timer switch, plus cables to connect them. The lights and solar panels have magnets as well as mounting holes. Pop them on metallic surfaces or bolt them down for permanent installation (fasteners not included). The battery works best when insulated from extreme temperatures—mount it inside your structure for optimal runtime. But if you have to install it outdoors, the battery will be protected from weather in a stainless steel enclosure that’s NEMA 3R rated.

Lights with a 100W solar panel work well in areas with at least 4 1/2 hrs. of direct sunlight between 9 AM and 3 PM. Lights with a 200W solar panel work well in areas with less than 4 1/2 hrs. of direct sunlight between 9 AM and 3 PM.

Two ceiling lights cover up to 160 sq. ft, about the size of a 20 ft. shipping container or small storage area. Three ceiling lights cover up to 320 sq. ft, about the size of a 40 ft. shipping container or small workshop.

To keep contaminants from entering your clean room, these lights seal against drop ceilings with an airtight gasket. They’re also covered in an antimicrobial paint and are fully enclosed. What makes them great for clean rooms also makes them great for washdowns and food preparation areas. They’re rated NSF/ANSI 2 for splash zones, so you can use them around splashing liquids from food. Rated IP65, they’re sealed against humidity and low-pressure washdowns. You can install these IC-rated lights in direct contact with insulation without risking a fire. Their lens disperses light evenly.

ISO class 3 lights have a prismatic lens that casts a beam that covers a wider area and limits glare better than lights with a smooth lens. If you don’t have a drop ceiling, no problem—these lights will also install into any finished ceiling opening with the built-in clamping arms.

Neutral lights are often used in workspaces. Cool lights highlight white and blue tones for higher visibility than neutral lights.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust. Install them anywhere that requires frequent cleaning, even an ISO Class 5 clean room. They also meet NSF/ANSI 2, so you can use them in food processing areas with splashing liquid. These lights won’t shatter and contaminate your area—they’re rated IK10, the highest rating for impact protection. And since they’re IC rated, you won’t risk a fire if you install them in direct contact with insulation.

Casting a neutral light dispersed by a frosted lens, these lights won’t cause glare on equipment. The lens is made of acrylic to resist scratching and yellowing.

Detect edges, take measurements, and spot holes with your machine vision camera by passing objects over these backlights. They cast even, low-intensity light that sits opposite from your inspection camera to produce a silhouette for your camera to focus on. Each backlight requires an M12 cable (sold separately) to power it.

White lights produce clean, crisp illumination in blue and white tones, which is ideal for inspection work. They’re a versatile choice to help your camera see objects made of any color. However, they will reflect on shiny surfaces.

Red lights won’t create a reflection or glare because the color is absorbed by materials, which makes them ideal for inspecting shiny glass, plastic, or metal objects. By creating a contrasting color, they’ll help you easily inspect the edges and contours of an object. However, red lights won't create enough contrast to inspect red-colored objects.

Backlights with an IP67-rated housing are sealed to keep out dust and moisture, so you can use them on the floor below your conveyor or even submerge them in water.

Add a mount to secure your backlight to a load-bearing surface. They secure with a bracket to keep your light still for consistent and accurate imaging with your inspection camera.

For technical drawings and 3-D models, click on a part number.

Illuminate signs and keyboards with a thin panel that's backlit by a circuit board of LED chips. Use the kit to light an existing display or print a custom design directly on the panel. Circuit boards have power connections on both ends; connect one end to a power source and cap the unused connection. To create two backlit panels, cut the circuit board in two and connect each half to a power source.