Brass Liners | McMaster-Carr

Also known as semimetallic woven strips and friction material, these strips have a brass wire woven into the material to increase strength and improve heat dissipation. They can be riveted or bonded. They do not contain asbestos.

	Wd.	Max. Rubbing Speed @ Pressure	Max. Coeff. of Friction	Max. Temp., ° F	Max. Pressure, psi		1 ft. Long	2 ft. Long	3 ft. Long	4 ft. Long	5 ft. Long	6 ft. Long	10 ft. Long	15 ft. Long	20 ft. Long	25 ft. Long
Woven



	3/16"	1"	5,000 fpm @ 200 psi	0.51	500	200	6224K341	00000	000000	000000	000000	000000	000000	000000	000000	0000000	0000000


	3/16"	1 1/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K342	0000	00000	00000	00000	00000	00000	00000	000000	000000	000000
	3/16"	1 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K343	0000	00000	00000	00000	00000	00000	00000	000000	000000	000000
	3/16"	1 3/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K344	0000	00000	00000	00000	00000	00000	00000	000000	000000	000000
	3/16"	2"	5,000 fpm @ 200 psi	0.51	500	200	6224K345	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	3/16"	2 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K346	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	3/16"	3"	5,000 fpm @ 200 psi	0.51	500	200	6224K347	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	1/4"	1"	5,000 fpm @ 200 psi	0.51	500	200	6224K348	0000	00000	00000	00000	00000	00000	00000	00000	000000	000000
	1/4"	1 1/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K349	0000	00000	00000	00000	00000	00000	00000	000000	000000	000000
	1/4"	1 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K351	0000	00000	00000	00000	00000	00000	00000	000000	000000	000000
	1/4"	1 3/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K352	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000


	1/4"	2"	5,000 fpm @ 200 psi	0.51	500	200	6224K353	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	1/4"	2 1/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K354	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	1/4"	2 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K355	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	1/4"	2 3/4"	5,000 fpm @ 200 psi	0.51	500	200	6224K356	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	1/4"	3"	5,000 fpm @ 200 psi	0.51	500	200	6224K357	00000	00000	00000	00000	00000	000000	000000	000000	000000	000000
	1/4"	3 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K358	00000	00000	00000	00000	000000	000000	000000	000000	000000	000000
	1/4"	4"	5,000 fpm @ 200 psi	0.51	500	200	6224K359	00000	00000	00000	00000	000000	000000	000000	000000	000000	000000
	1/4"	5"	5,000 fpm @ 200 psi	0.51	500	200	6224K361	00000	00000	00000	000000	000000	000000	000000	000000	000000	000000
	5/16"	2"	5,000 fpm @ 200 psi	0.51	500	200	6224K362	00000	00000	00000	00000	00000	00000	000000	000000	000000	000000
	5/16"	3"	5,000 fpm @ 200 psi	0.51	500	200	6224K363	00000	00000	00000	00000	000000	000000	000000	000000	000000	000000


	3/8"	2"	5,000 fpm @ 200 psi	0.51	500	200	6224K364	00000	00000	00000	00000	00000	000000	000000	000000	000000	000000
	3/8"	3"	5,000 fpm @ 200 psi	0.51	500	200	6224K365	00000	00000	00000	000000	000000	000000	000000	000000	000000	000000
	3/8"	3 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K366	00000	00000	00000	000000	000000	000000	000000	000000	000000	000000
	3/8"	4"	5,000 fpm @ 200 psi	0.51	500	200	6224K367	00000	00000	00000	000000	000000	000000	000000	000000	000000	000000
	3/8"	5 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K368	00000	00000	000000	000000	000000	000000	000000	000000	000000	00000000
	1/2"	2 1/2"	5,000 fpm @ 200 psi	0.51	500	200	6224K369	00000	00000	00000	000000	000000	000000	000000	000000	000000	000000
	1/2"	3"	5,000 fpm @ 200 psi	0.51	500	200	6224K371	00000	00000	000000	000000	000000	000000	000000	000000	000000	000000
	1/2"	4"	5,000 fpm @ 200 psi	0.51	500	200	6224K372	00000	00000	000000	000000	000000	000000	000000	000000	000000	00000000
	1/2"	5"	5,000 fpm @ 200 psi	0.51	500	200	6224K373	00000	000000	000000	000000	000000	000000	000000	000000	00000000	00000000
	1/2"	6"	5,000 fpm @ 200 psi	0.51	500	200	6224K374	00000	000000	000000	000000	000000	000000	000000	000000	00000000	00000000


	1/2"	8"	5,000 fpm @ 200 psi	0.51	500	200	6224K375	00000	000000	000000	000000	000000	000000	000000	00000000	00000000	00000000

Wraparound Bench Vise Jaw Liners

Fold the pliable tabs over vise jaws to protect workpieces from marring.

Smooth

		Overall
	For Jaw Wd.	Wd.	Ht.	Thk.		Pair
Brass



		8"	8"	1 3/4"	5"	5254A51	0000000

Door Kick Plates

Kick plates prolong the life of doors by shielding them from scratches, dings, and marks in high-traffic areas. They also keep moisture from damaging the base of doors in facilities that require frequent mopping and cleaning. Our kick plates are tested with salt spray to meet ANSI A156.6 requirements for strength, appearance, and durability. They stay looking like new, even when installed outdoors in humid or wet environments.

Screw In

Mount with the included self-drilling screws and skip drilling a hole. The screws match the finish of the plates and sit flush to create a clean, smooth look.

Brass—With a shiny, warm finish, these kick plates give doors an elegant appeal. They resist corrosion about as well as 304 stainless steel but require occasional polishing to clean up smudges and avoid tarnish.

Width—Select a kick plate 2" narrower than your door to prevent obstructions when opening and closing it.

Height—Kick plates 34" to 46" in height guard against damage from carts or dollies better than shorter plates.

	Ht.	Thk.	For Use Outdoors	Mounting Fasteners Included		Polished Brass
24" Wide



		34"	0.05"	Yes	Yes	1401A51	0000000


		28" Wide



				6"	0.05"	Yes	Yes	1401A52	000000


				8"	0.05"	Yes	Yes	1401A53	000000
				10"	0.05"	Yes	Yes	1401A54	000000
				12"	0.05"	Yes	Yes	1401A55	000000
				36"	0.05"	Yes	Yes	1401A56	000000
				42"	0.05"	Yes	Yes	1401A57	000000


				30" Wide



						6"	0.05"	Yes	Yes	1401A58	000000


						8"	0.05"	Yes	Yes	1401A59	000000
						10"	0.05"	Yes	Yes	1401A61	000000
						12"	0.05"	Yes	Yes	1401A62	000000


						34" Wide



								6"	0.05"	Yes	Yes	1401A63	000000


								8"	0.05"	Yes	Yes	1401A64	000000
								10"	0.05"	Yes	Yes	1401A65	000000
								12"	0.05"	Yes	Yes	1401A66	000000
								16"	0.05"	Yes	Yes	1401A67	000000
								34"	0.05"	Yes	Yes	1401A68	000000
								36"	0.05"	Yes	Yes	1401A69	000000
								46"	0.05"	Yes	Yes	1401A71	000000


								36" Wide



										8"	0.05"	Yes	Yes	1401A72	000000


										10"	0.05"	Yes	Yes	1401A73	000000
										12"	0.05"	Yes	Yes	1401A74	000000


										48" Wide



												8"	0.05"	Yes	Yes	1401A75	000000


12"	0.05"											Yes	Yes	1401A76	000000
16"	0.05"											Yes	Yes	1401A77	000000

Fabric Grommet Kits

Kits include grommets of a single size and all the tools you need to install them. The grommets add a protective metal ring to a hole so rope and cable don’t tear your tarp, cover, or curtain. Strike the cutting punch with a mallet to create a hole, then set the grommet using the installation punch and die set.

Standard Washer

Brass—Add a bright finish to your fabric.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Mil. Spec.	Includes	No. of Grommets		Each
Brass



	0	0.1"	1/4"	0.545"	0.175"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K31	000000


	1	0.1"	9/32"	0.687"	0.185"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K32	00000
	2	0.14"	3/8"	0.815"	0.215"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K13	00000
	3	0.21"	7/16"	0.97"	0.295"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	12	9610K34	00000
	4	0.29"	1/2"	1.05"	0.374"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	12	9610K35	00000

Tooth-Lock Washer

Teeth grip the fabric for a stronger hold than standard washers.

Brass—Add a bright finish to your fabric.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Mil. Spec.	Includes	No. of Grommets		Each
Brass



	0	0.11"	1/4"	0.545"	0.175"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	48	9610K16	000000


	1	0.12"	9/32"	0.687"	0.185"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	48	9610K17	00000
	2	0.15"	3/8"	0.815"	0.215"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K18	00000
	3	0.23"	7/16"	0.97"	0.295"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K19	00000
	4	0.3"	1/2"	1.05"	0.374"	Yes	MIL-G-16491	Cutting Block, Cutting Punch, Die Set, Installation Punch	24	9610K21	00000

Fabric Grommets

Add a protective metal ring to a hole so rope and cable don’t tear your tarp, cover, or curtain. To install, strike a cutting punch with a mallet to create the hole, then set the grommet using either an installation punch or a press. All of these grommets can be used outdoors. Installation tools are sold separately.

Standard Washer

Brass—Add a bright finish to your fabric.

Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Specs. Met	Pkg. Qty.		Pkg.
Brass



	00	0.063"	3/16"	0.425"	0.135"	Yes	NASM20230	50	9604K21	00000


	0	0.101"	1/4"	0.545"	0.175"	Yes	NASM20230	50	9604K22	0000
	1	0.108"	9/32"	0.687"	0.185"	Yes	NASM20230	50	9604K23	0000
	2	0.14"	3/8"	0.815"	0.215"	Yes	NASM20230	50	9604K24	00000
	3	0.219"	7/16"	0.97"	0.295"	Yes	NASM20230	50	9604K25	00000
	4	0.298"	1/2"	1.05"	0.374"	Yes	NASM20230	50	9604K26	00000
	5	0.254"	5/8"	1.22"	0.33"	Yes	NASM20230	25	9604K27	00000
	6	0.149"	13/16"	1.75"	0.232"	Yes	NASM20230	10	9604K28	00000


	Nickel-Plated Brass



			00	0.063"	3/16"	0.425"	0.135"	Yes	NASM16491	50	86625K31	0000


			0	0.101"	1/4"	0.545"	0.175"	Yes	NASM16491	50	86625K32	00000
			1	0.108"	9/32"	0.687"	0.185"	Yes	NASM16491	50	86625K33	00000
			2	0.14"	3/8"	0.815"	0.215"	Yes	NASM16491	50	86625K34	00000
			3	0.219"	7/16"	0.97"	0.295"	Yes	NASM16491	50	86625K35	00000
			4	0.298"	1/2"	1.05"	0.374"	Yes	NASM16491	25	86625K36	00000
			5	0.254"	5/8"	1.22"	0.33"	Yes	NASM16491	25	86625K37	00000
			6	0.149"	13/16"	1.75"	0.232"	Yes	NASM16491	10	86625K38	00000

Accessories for Grommets

Installation and Cutting Punches

Hammer-Driven

Installation

Punch

Hammer-Driven

Cutting Punch

Hammer-Driven Installation Punch—The economical choice if you’re installing a few grommets at a time. Align the grommet base, fabric, and washer on the die (included). A few sharp taps on the punch cinch the grommet in the hole. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.

Hammer-Driven Cutting Punch—Create a hole in your fabric with a few sharp mallet taps on the cutting punch. Use a rubber or rawhide mallet rather than a metal hammer to preserve the head of the punch.

	For Hole Dia.	Material		Each
Hammer-Driven Installation Punch



	00	3/16"	—	9612K25	000000


	0	1/4"	—	9612K26	00000
	1	9/32"	—	9612K27	00000
	2	3/8"	—	9612K28	00000
	3	7/16"	—	9612K29	00000
	4	1/2"	—	9612K31	00000
	5	5/8"	—	9612K32	00000
	6	13/16"	—	9612K33	00000


	Hammer-Driven Cutting Punch



			00	3/16"	Steel	9611K11	00000


			0	1/4"	Steel	9611K12	00000
			1	9/32"	Steel	9611K13	00000
			2	3/8"	Steel	9611K14	00000
			3	7/16"	Steel	9611K15	00000
			4	1/2"	Steel	9611K16	00000
			5	5/8"	Steel	9611K17	00000
			6	3/4"	Steel	9611K18	00000

Manual Presses

Manual Press

Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.

		Throat
	Max. Opening	Dp.	Wd.	Material		Each
Manual Press



		7/8"	3 1/4"	1 3/4"	Aluminum	95720A690	0000000

For Grommet Trade Size	Hole Size		Each
00	3/16"	95720A710	000000
0	1/4"	95720A715	00000
1	9/32"	95720A720	00000
2	3/8"	95720A730	00000
3	7/16"	95720A740	00000

Tooth-Lock Washer

Teeth grip the fabric for a stronger hold than standard washers.

Brass—Add a bright finish to your fabric.

Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Specs. Met	Pkg. Qty.		Pkg.
Brass



	0	0.101"	1/4"	0.545"	0.175"	Yes	NASM16491	50	9605K21	00000


	1	0.108"	9/32"	0.687"	0.185"	Yes	NASM16491	50	9605K22	0000
	2	0.141"	3/8"	0.815"	0.215"	Yes	NASM16491	50	9605K23	00000
	3	0.219"	7/16"	0.97"	0.295"	Yes	NASM16491	50	9605K24	00000
	4	0.295"	1/2"	1.05"	0.374"	Yes	NASM16491	50	9605K25	00000
	5	0.251"	5/8"	1.22"	0.33"	Yes	NASM16491	25	9605K26	00000


	Nickel-Plated Brass



			0	0.101"	1/4"	0.545"	0.175"	Yes	NASM16491	50	9604K31	0000


			1	0.108"	9/32"	0.687"	0.185"	Yes	NASM16491	50	9604K32	00000
			2	0.141"	3/8"	0.815"	0.215"	Yes	NASM16491	50	9604K33	00000
			3	0.219"	7/16"	0.97"	0.295"	Yes	NASM16491	25	9604K34	0000

Accessories for Grommets

Installation and Cutting Punches

Hammer-Driven

Installation

Punch

Hammer-Driven

Cutting Punch

	For Hole Dia.	Material		Each
Hammer-Driven Installation Punch



	0	1/4"	—	9612K26	000000


	1	9/32"	—	9612K27	00000
	2	3/8"	—	9612K28	00000
	3	7/16"	—	9612K29	00000
	4	1/2"	—	9612K31	00000
	5	5/8"	—	9612K32	00000


	Hammer-Driven Cutting Punch



			0	1/4"	Steel	9611K12	00000


			1	9/32"	Steel	9611K13	00000
			2	3/8"	Steel	9611K14	00000
			3	7/16"	Steel	9611K15	00000
			4	1/2"	Steel	9611K16	00000
			5	5/8"	Steel	9611K17	00000

Manual Presses

Manual Press

		Throat
	Max. Opening	Dp.	Wd.	Material		Each
Manual Press



		7/8"	3 1/4"	1 3/4"	Aluminum	95720A690	0000000

Reinforcing Fabric Grommets

These grommets handle thick materials and strain from fabric that’s frequently pulled or stretched. Strike a cutting punch with a mallet to create the hole, then set the grommet using either an installation punch or a press. Installation tools are sold separately.

Extended-Neck Washer

An extended neck gives these washers a stronger hold than our other fabric grommets.

Brass—Add a bright finish to your fabric.

Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Mil. Spec.	Specs. Met	Pkg. Qty.		Pkg.
Brass



	00	0.062"	3/16"	0.425"	0.135"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	8271K31	00000


	0	0.102"	1/4"	0.545"	0.175"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	8271K32	00000
	1	0.112"	9/32"	0.687"	0.185"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	8271K33	00000
	2	0.139"	3/8"	0.815"	0.215"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	8271K34	00000
	3	0.218"	7/16"	0.97"	0.295"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	8271K35	00000
	4	0.296"	1/2"	1.05"	0.374"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	25	8271K36	00000


	Nickel-Plated Brass



			00	0.062"	3/16"	0.425"	0.135"	Yes	AN230, MIL-G-16491	NASM20230	50	9604K35	0000


			0	0.102"	1/4"	0.545"	0.175"	Yes	AN230, MIL-G-16491	NASM20230	50	9604K36	0000
			1	0.112"	9/32"	0.687"	0.185"	Yes	AN230, MIL-G-16491	NASM20230	50	9604K37	00000
			2	0.139"	3/8"	0.815"	0.215"	Yes	AN230, MIL-G-16491	NASM20230	50	9604K38	00000
			3	0.218"	7/16"	0.97"	0.295"	Yes	AN230, MIL-G-16491	NASM20230	25	9604K39	00000

Accessories for Grommets

Installation and Cutting Punches

Hammer-Driven

Installation

Punch

Hammer-Driven

Cutting Punch

	For Hole Dia.	Material		Each
Hammer-Driven Installation Punch



	00	3/16"	—	9612K25	000000


	0	1/4"	—	9612K26	00000
	1	9/32"	—	9612K27	00000
	2	3/8"	—	9612K28	00000
	3	7/16"	—	9612K29	00000
	4	1/2"	—	9612K31	00000


	Hammer-Driven Cutting Punch



			00	3/16"	Steel	9611K11	00000


			0	1/4"	Steel	9611K12	00000
			1	9/32"	Steel	9611K13	00000
			2	3/8"	Steel	9611K14	00000
			3	7/16"	Steel	9611K15	00000
			4	1/2"	Steel	9611K16	00000

Manual Presses

Manual Press

		Throat
	Max. Opening	Dp.	Wd.	Material		Each
Manual Press



		7/8"	3 1/4"	1 3/4"	Aluminum	95720A690	0000000

For Grommet Trade Size	Hole Size		Each
00	3/16"	95720A710	000000
0	1/4"	95720A715	00000
1	9/32"	95720A720	00000
2	3/8"	95720A730	00000
3	7/16"	95720A740	00000

Rolled Rim with Tooth-Lock Washer

Teeth grip the fabric for an even stronger hold than other reinforcing fabric grommets. Use these washers for fabric under the highest strain, such as a tarp secured by bungee cords.

Brass—Add a bright finish to your fabric.

Nickel-Plated Brass—The nickel gives these a more muted, silvery look than our other brass grommets.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Mil. Spec.	Specs. Met	Pkg. Qty.		Pkg.
Brass



	0	0.096"	9/32"	0.67"	0.175"	Yes	AN230, MIL-G-16491	NASM20230	50	9606K41	000000


	1	0.126"	13/32"	0.79"	0.205"	Yes	AN230, MIL-G-16491	NASM20230	50	9606K42	00000
	2	0.174"	7/16"	0.89"	0.255"	Yes	AN230, MIL-G-16491	NASM20230	25	9606K43	00000
	3	0.172"	15/32"	0.97"	0.255"	Yes	AN230, MIL-G-16491	NASM20230	25	9606K44	00000
	4	0.237"	9/16"	1.12"	0.32"	Yes	AN230, MIL-G-16491	NASM20230	25	9606K45	00000
	5	0.296"	5/8"	1.285"	0.38"	Yes	AN230, MIL-G-16491	NASM20230	10	9606K46	0000
	6	0.332"	3/4"	1.535"	0.42"	Yes	AN230, MIL-G-16491	NASM20230	5	9606K47	0000
	7	0.363"	29/32"	1.725"	0.446"	Yes	AN230, MIL-G-16491	NASM20230	5	9606K48	00000
	8	0.382"	1 3/32"	1.865"	0.465"	Yes	AN230, MIL-G-16491	NASM20230	5	9606K49	00000


	Nickel-Plated Brass



			0	0.096"	9/32"	0.67"	0.175"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	50	87995K51	00000


			1	0.126"	13/32"	0.79"	0.205"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	25	87995K52	00000
			2	0.174"	7/16"	0.89"	0.255"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	25	87995K53	00000
			3	0.172"	15/32"	0.97"	0.255"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	25	87995K54	00000
			4	0.237"	9/16"	1.12"	0.32"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	10	87995K55	0000
			5	0.296"	5/8"	1.285"	0.38"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	10	87995K56	00000
			6	0.332"	3/4"	1.535"	0.42"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	5	87995K57	0000
			7	0.363"	29/32"	1.725"	0.446"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	5	87995K58	00000
			8	0.382"	1 3/32"	1.865"	0.465"	Yes	AN230, MIL-G-16491	NASM16491, NASM20230	5	87995K59	00000

Accessories for Grommets

Installation and Cutting Punches

Hammer-Driven

Installation

Punch

Hammer-Driven

Cutting Punch

	For Hole Dia.	Material		Each
Hammer-Driven Installation Punch



	0	9/32"	—	9612K17	000000


	1	13/32"	—	9612K18	00000
	2	7/16"	—	9612K19	00000
	3	15/32"	—	9612K21	00000
	4	9/16"	—	9612K22	00000
	5	5/8"	—	9612K23	00000
	6	3/4"	—	9612K24	00000
	7	29/32"	—	9612K35	000000
	8	1 3/32"	—	9612K36	000000


	Hammer-Driven Cutting Punch



			0	1/4"	Steel	9611K12	00000


			1	9/32"	Steel	9611K13	00000
			2	3/8"	Steel	9611K14	00000
			3	7/16"	Steel	9611K15	00000
			4	1/2"	Steel	9611K16	00000
			5	5/8"	Steel	9611K17	00000
			6	3/4"	Steel	9611K18	00000
			7	7/8"	Steel	9611K19	00000
			8	1"	Steel	9611K21	00000

Manual Presses

Manual Press

		Throat
	Max. Opening	Dp.	Wd.	Material		Each
Manual Press



		7/8"	3 1/4"	1 3/4"	Aluminum	95720A690	0000000

For Grommet Trade Size	Hole Size		Each
0	9/32"	95720A810	000000
1	13/32"	95720A820	00000

Self-Piercing Fabric Grommets

Save time installing grommets in tarps and covers without precut holes. Set grommets in a bench-mount manual press with die set, and the sharp neck of the grommet cuts the material as you press it into place. Installation tools are sold separately.

Standard Washer

Grommets with trade size 0, 1, and 2 require a die set adapter for installation.

Brass—Add a bright finish to your fabric.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Pkg. Qty.		Pkg.
Brass



	0	0.091"	1/4"	0.562"	0.154"	No	50	7253K11	000000


	1	0.091"	5/16"	0.625"	0.154"	No	50	7253K12	00000
	2	0.091"	3/8"	0.75"	0.154"	No	50	7253K13	00000
	3	0.091"	7/16"	0.938"	0.154"	No	25	7253K14	00000
	4	0.091"	5/8"	1.125"	0.154"	No	25	7253K15	00000

Accessories for Grommets

Manual Presses

Bench-Mount Manual

Press

Bench-Mount Manual Press—Saves time and effort if you’re frequently installing or replacing grommets. Install the required two-piece die set (sold separately) on the press, align the grommet in the hole, and squeeze the handle. For a longer service life, lubricate the handle and plunger with a drop of oil.

			Material
	Throat Dp.	Press Ht.	Frame	Ram	Mounting Fasteners Included		Each
Bench-Mount Manual Press



		4 3/4"	8"	Iron	Steel	No	95715A690	0000000

For Grommet Trade Size		Each
0	7253K111	000000
1	7253K112	00000
2	7253K113	00000
3	7253K211	000000
4	7253K212	000000

For Grommet Trade Size		Each
0, 1, 2	7253K33	000000

Tooth-Lock Washer

Teeth grip the fabric for a stronger hold than standard washers.

Brass—Add a bright finish to your fabric.

Grommet Trade Size—Make sure your grommet, hole, and installation tools have the same trade size.

	For Max. Material Thk.	ID	Flange Dia.	Dp. Under Flange	For Use Outdoors	Pkg. Qty.		Pkg.
Brass



	0	0.126"	9/32"	0.688"	0.189"	No	50	8276K41	000000


	1	0.126"	3/8"	0.75"	0.189"	No	50	8276K42	00000
	2	0.126"	7/16"	0.875"	0.189"	No	25	8276K43	00000
	4	0.126"	9/16"	1.125"	0.189"	No	10	8276K44	0000

Accessories for Grommets

Manual Presses

Bench-Mount Manual

Press

			Material
	Throat Dp.	Press Ht.	Frame	Ram	Mounting Fasteners Included		Each
Bench-Mount Manual Press



		4 3/4"	8"	Iron	Steel	No	95715A690	0000000

Brass Unthreaded Inserts for Plastic

Made from brass, these inserts are nonmagnetic, mildly corrosion resistant, and electrically conductive. Also known as compression limiters, they keep screws securely installed even if the surrounding plastic expands or shrinks when the screw is tightened.

	Lg.	Lg. Tolerance	OD	OD Tolerance	For Hole Dia.	Pkg. Qty.		Pkg.
Brass



	No. 4	1/8"	-0.006" to 0.000"	0.244"	0.000" to 0.006"	0.245" to 0.248"	10	91999A100	000000


	No. 4	0.187"	-0.006" to 0.000"	0.244"	0.000" to 0.006"	0.245" to 0.248"	5	91999A101	0000
	No. 6	1/8"	-0.006" to 0.000"	0.268"	0.000" to 0.006"	0.269" to 0.272"	10	91999A102	00000
	No. 6	1/4"	-0.006" to 0.000"	0.268"	0.000" to 0.006"	0.269" to 0.272"	5	91999A103	0000
	No. 8	0.156"	-0.006" to 0.000"	0.304"	0.000" to 0.006"	0.305" to 0.308"	5	91999A104	0000
	No. 8	1/4"	-0.006" to 0.000"	0.304"	0.000" to 0.006"	0.305" to 0.308"	5	91999A105	0000
	No. 10	0.187"	-0.006" to 0.000"	0.364"	0.000" to 0.006"	0.365" to 0.368"	5	91999A106	0000
	No. 10	1/4"	-0.006" to 0.000"	0.364"	0.000" to 0.006"	0.365" to 0.368"	5	91999A107	0000
	1/4"	1/4"	-0.006" to 0.000"	0.436"	0.000" to 0.006"	0.437" to 0.44"	5	91999A108	0000
	1/4"	0.312"	-0.006" to 0.000"	0.436"	0.000" to 0.006"	0.437" to 0.44"	5	91999A109	0000