Connect these modular pumps to your air system and add a reservoir and solenoid valve to automate the flow of oil. Install or remove pumps as your lubrication needs change. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw.

Pumps with spray nozzle provide a broader dispensing pattern. Nozzle bends and stays in position.

Note: For proper operation, pumps require a three-way solenoid valve (sold separately). The solenoid can be controlled by a timer or PLC (programmable logic controller).

For technical drawings and 3-D models, click on a part number.

Connect these dispensers to your air system to pressurize the oil in the reservoir and atomize the spray. Dual regulators allow you to adjust the pressure of the oil and the atomized spray. Add a spray valve (sold separately) to direct the flow of oil. A removable filter prevents valve blockage. They have NPTF (Dryseal) threads, which are compatible with NPT threads.

Ready to connect to your air system, these complete systems include a timer and a reservoir. Turn the dials to set the cycle interval. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw. Pumps and their components come mounted on a panel.

For technical drawings and 3-D models, click on a part number.

Dispense a fixed amount of oil by pumping the handle. To control flow to multiple lubrication points, use metering valves (sold separately).

Vertical pump dispenses oil when you pull the handle. Horizontal pumps dispense oil when you release the handle.

Use these valves with manual and electric pumps to dispense different amounts of oil from multiple lubrication points. They have a check valve to prevent backward flow. To connect to tubing, use a compression nut and sleeve (sold separately).

Flow rate trade number indicates the relative amount of oil each valve delivers. For each increase in trade size, the amount of oil delivered approximately doubles. For example, 0 delivers twice the amount of oil that 00 delivers. In a system with two lubrication points, the lubrication point connected to 0 will receive 2/3 of the oil dispensed, and the lubrication point connected to 00 will receive 1/3 of the oil dispensed. In general, valves with lower relative flow rates are better for cycling systems; valves with higher relative flow rates are better for continuous recirculation systems.

Designed to recycle oil, this system dispenses, collects, and filters oil for reuse. It delivers a controlled flow at a specific interval. It's often used to drip oil over gears, bearings, and crankshafts. To adjust the flow, use a wrench to remove the pump from the reservoir and turn the adjustment nut. The system can be used with any oil grade. Flow rate depends on temperature.

These manual dispensers are more portable than air-powered dispensers.

Style A mounts to a 5-gal. pail of oil (not included).

Equipped with a flowmeter/totalizer, this dispenser displays both flow rate and cumulative flow volume of the oil dispensed. Mount it to your drum of oil. It's smaller and more portable than air-powered container-mount dispensers, making it good for refilling gear boxes and transmissions. The container is not included.

Driven by an air-powered pump, this dispenser comes with an adapter to mount through a bung opening on a drum of oil (not included).

Add faucets to oil dispensing stations for increased utility.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers. They include one faucet and can fit up to three, so you can access different types of oil at a single centralized point.

Stations with a meter measure oil as it's dispensed.

Dispense from your drum or pail of grease using compressed air. Dispensers include a follower plate that moves down the inside of the container as the grease level drops to compress the grease and prevent vapor pockets. Containers not included.

Dispensers deliver grease at the same pressure as your existing grease system, up to the max. grease outlet pressure. Dispensers with a booster gun allow you to increase the pressure to the value listed for max. grease outlet pressure with booster.

Styles A-D have a Z-swivel that connects the outlet hose to the gun and prevents the hose from kinking.

For technical drawings and 3-D models, click on a part number.

This dispenser delivers over three times more grease per stroke than our dual-output dispensers. Use it with your pail of grease. Container not included.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing. Dispensers include a follower plate that moves down the inside of the container as the grease level drops to compress the grease and prevent vapor pockets.

Styles A and C do not include a container. Use them with your pail of grease.

Gun with flexible nozzle includes a Z-swivel, which connects to the outlet hose to prevent it from kinking.

Increase the pressure of your grease system when necessary to dispense thick grease and force grease through clogged fittings. Note: Do not use flexible nozzles with these booster guns.

A display allows you to monitor how much grease is dispensed. Toggle between the resettable batch total and the cumulative total that cannot be reset. The included Z-swivel connects to an outlet hose, so the gun can move in any direction without kinking the hose.

Use the keypad to select from six dispensing durations: 15 days, 1 month, 2 months, 3 months, 6 months, and 12 months.

Battery and grease packs (sold separately) must be installed and replaced at the same time for proper operation.

Connect a manifold (sold separately) to lubricate multiple points. Manifolds with mounting kit include connectors, adapters, tubing, and mounting hardware—all the components required to set up lubrication to multiple points.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease. Install or remove pumps as your lubrication needs change. Mounting holes are drilled through the pump's body. Each pump has a separate flow adjustment; use a screwdriver to turn the flow-adjustment screw.

Note: For proper operation, pumps require a three-port solenoid valve (sold separately). The solenoid can be controlled by a timer or PLC (programmable logic controller).

For technical drawings and 3-D models, click on a part number.