Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Add lubrication to your air supply to extend the service life of air-powered tools and equipment.

Replace a damaged bowl on your Norgren modular compressed air lubricator.

Replace a damaged bowl, or change the bowl material on your Parker modular compressed air lubricator.

Replace a damaged bowl, or change the bowl material on your ARO modular compressed air lubricator.

Replace a cracked or lost sight dome on your SMC modular compressed air lubricator.

Replace a cracked or lost sight dome on your Norgren modular compressed air lubricator.

An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

An ASCO Numatics filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.

With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.

Also known as coalescing filters, these filters remove compressor oil to extend the service life of air-powered tools and equipment.

Connect a tube fitting and tubing to the dispenser outlet to access hard-to-reach lubrication points.

Serve multiple lubrication points from a single location.

Control the flow of oil to a single lubrication point.

Mount these reservoirs directly to your machine, or use them with a flow-adjustment valve and brush to create a dispenser.

A sealed design prevents contamination in dirty and dusty environments. Install a line between the reservoir's pressure port and the lubricated equipment to balance pressure.

Connect these brushes to oil reservoirs and flow adjustment valves to lubricate chain, gears, and conveyors.

As chain, gears, and conveyors move, these brushes rotate to apply lubricant.

A sealed design prevents contamination in dirty and dusty environments.

Manually adjust the flow of oil to a single lubrication point.

A solenoid automatically starts and stops flow to dispense lubricant while equipment is running.

Use these brushes to lubricate chain, gears, and conveyors. Connect to an oil dispenser, then turn the dial to adjust flow.

Air pressurizes the oil in the reservoir and atomizes the spray. Add a spray valve to direct the flow of oil.

Choose from pumps that dispense with a set interval. Turn the dial to adjust the flow from 0.1 oz. to 0.2 oz. per cycle.

Set the cycle interval as well as the dispensing duration. This pump has a maximum flow of 0.1 oz. per second.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

Deliver a mist of oil using shop air.

These dispensers have an opening for filling without removing the nozzle.

Clamp this applicator around control cables to lubricate them with minimal mess.

Equipped with a flowmeter/totalizer, this dispenser displays both the flow rate and the cumulative flow volume of the oil dispensed.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers.

These dispensers come packed with grease, eliminating the mess of filling. Turn the dial to adjust flow rate.

Turn the metering pin to adjust flow rate.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease.

Lubricate single- and double-strand roller chain.

Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.

With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.

These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.

Dispense from grease guns into grease fittings and bare lubrication points.

Convert dispensing tips with male threads into quick-disconnect couplings.

These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.

Mount holders in convenient locations to keep grease guns within reach.

Dispense grease with the highest-pressure-rated gun we offer.

These guns deliver twice as much grease per stroke than standard lever-grip guns.

Designed to lubricate linear motion components, such as slide bearings, guides, and ball screws, these guns work exclusively with THK grease cartridges and fittings.

Dispensing more grease per pump than pistol-grip guns, lever-grip guns are better for applications that require high grease output.

Deliver small amounts of grease with only a light push against the lubrication point.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Turn a small tube of grease into a dispenser.

Dispense small amounts of grease with one of these compact guns.

Replace the dispensing tip on your filler pump.

Switch between high-pressure and low-pressure settings. Use high pressure to dispense thicker grease or to force grease through clogged fittings. Use low pressure for high-volume dispensing.

Move grease-dispensing guns in any direction without kinking the outlet hose.

Connect these guns to container-mount dispensers for controlled dispensing.

A display allows you to monitor how much grease is dispensed.

Draw coolant from your existing tank.

Deliver a small, controlled amount of coolant to a workpiece.

These dispensers have a reservoir for recirculating coolant.

Kits contain lengths of hose, nozzles, valves, and caps.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Kit contains lengths of hose, nozzles, connectors, and assembly pliers.

Use with Loc-Line hose to assemble and disassemble components.

This hose is made of steel.

These nozzles handle coolant pressure up to 150 psi.

Press these nozzles into unthreaded holes.

For use in the highest pressure coolant lines, these nozzles are rated for at least 1,000 psi.