A plastic pad on the gripping surface of these clamps prevents workpiece marring, making them useful for holding polished surfaces and reducing the need for secondary finishing steps.

Setup Clamps for Angled Workpieces

Unlike other setup clamps that grip the horizontal surface of a workpiece, these clamps have a pivoting ball in the tip to get a firm hold on angled parts.

Setup Clamp Supports

Keep setup clamps from falling out of position when they are unclamped—the spring holds them up for quick workpiece insertion and removal. Also known as spring lifters.

Side Clamps

Also known as toe clamps, these grip the side of a workpiece to leave the top free for machining.

T-Slot Side Clamps

The built-in T-slot nut on these side clamps lets you clamp a part to a machine table quickly. Their small footprint leaves more free space on your table than standard side clamps.

Vise Mounting Clamps

Smaller than standard setup clamps, these clamps leave more usable space on a machine table when mounting a vise.

Machine Table Clamps
for Round Workpieces

Use these clamps to hold large round parts for machining. Each clamp comes with five lengths of chain that combine to accommodate different size workpieces.

Parallel Handscrew Clamps

The matching jaws are ground flat for a firm grip and even pressure when clamping smooth surfaces.

Machinable Low-Profile
Fixture Clamps

Machine these fixture clamps to match the contours of your workpiece for a stronger grip.

Low-Profile Fixture Clamps

Install these clamps into a slot in your fixture to grip at the bottom of a workpiece edge, giving the cutting tool maximum access.

Machinable Fixture Clamps

Machine these clamps to match the contours of your workpiece and turn the screw to grip.

Machinable Dual-Clamping
Fixture Clamps

Machine these fixture clamps to match the contours of your workpieces for a stronger grip. Place the clamp between the two workpieces in a fixture and tighten the screw to extend the sides of the clamp, creating a secure hold against both workpieces.

Fixture Clamps

Hold a workpiece securely from the side with minimal contact, leaving more of the workpiece free for machining.

Fixture Clamps for
Castings and Rough Parts

Unlike the smooth and flat edges of standard fixture clamps, these clamps have ridges that bite into parts, making them good for gripping castings and rough-cut stock.

Dual-Clamping Fixture Clamps

Set one of these clamps between two workpieces in a fixture and tighten the screw to push the clamp's sides out for a secure hold.

Hydraulic-Powered
Hold-Down Fixture Clamps

Use the power of hydraulic fluid to quickly, consistently, and repeatedly clamp and release parts with a greater clamping force than air-powered hold-down fixture clamps.

Threaded Air-Powered
Hold-Down Fixture Clamps

Screw these clamps directly into a tapped hole in a fixture.

Inside Diameter Fixture Clamps

Secure a workpiece from the inside, leaving the outside clear for machining.

Inside Diameter Fixture Clamps
for Castings and Rough Parts

These clamps wedge against the workpiece ID to grip cast, unfinished, or uneven parts, leaving the outside clear for machining.

Air-Powered Hold-Down
Fixture Clamps

Mount using the holes in the base.

Ball-Lock Quick-Change
Fixture Clamps

Build these components into fixture plates, machine subplates, and tombstones for quick changes. The system clamps and locates at the same time for accurate positioning with repeatability of ±0.0005".

Hold-Down Fixture Clamps

Tighten the spring-loaded socket head cap screw on these clamps to hold your workpiece from above.

Parallel-Jaw Bar Clamps/Spreaders

The large, flat jaws remain parallel when clamping to apply even pressure without denting or marring the workpiece. Pull the handle to lock or release the clamping arm.

Inspection and Measuring Fixturing

Use these components in coordinate measuring machine (CMM) applications to raise a workpiece and reliably position it on a fixture plate with ¼"-20 holes.

T-Slot Blocks

Mount these versatile blocks to any flat surface for machine table-style T-slot clamping. They can also be used on a machine table to clamp parts at specific angles or add more total clamping points.

Parallel Keepers

Spring-loaded to keep parallels in place on a vise. Also known as parallel separators.

Heavy Duty Cam Handles

Also known as double cams, these complete cam handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Create-Your-Own Heavy
Duty Cam Handles

Add a pin, rod-end bolt, or other mounting hardware to build a custom assembly. Also known as double cams, these handles have a durable, extra-large handle for clamping on fixture bases, plates, and workpieces. For fast adjustments, push down on the handle and the head applies pressure to quickly draw two parts together.

Cam Handles

Use these standard cam handles for most clamping applications. Push down on the handle and the head applies pressure to quickly draw two parts together for fast adjustments.

Expanding Cam Handles
for Unthreaded Holes

Use these handles to keep holes aligned or lift several sheets of thin material. They have a plug that expands to grip the edges inside holes. They are not suitable for permanent installation—use only for temporary mounting.