These switches are protected from corrosion, high-temperature and high-pressure washdowns, and oil/coolant spraying. Install them in 22 mm dia. cutouts.

Rated NEMA 4, 13, and IP66, these metal switches are protected from washdowns and oil/coolant spraying. Install them in 30 mm dia. cutouts.

Rated NEMA 3S, 4X and 13, these switches are protected from corrosion, washdowns, and oil/coolant spraying.

The built-in contact block in these switches extends behind the panel half the depth of most other 22 mm switches, saving valuable space.

The face of these switches mounts flush against a panel, so they're easy to clean and hard to damage.

A single-piece construction prevents the contact block from separating from the actuator in high-vibration applications.

Immediately cut power with a single push.

Use these switches where ignitable gas and dust may be present. Their contact blocks are UL listed for Class I, Division 2, Groups B, C, and D hazardous locations.

Sized for 4 mm or 6 mm panel cutouts, these switches are often used with circuit boards to control electronics.

Because these switches mount flush against a panel, they're easy to clean and hard to damage.

These aluminum switches are rated NEMA 4, NEMA 13, and IP66 for protection from washdowns and oil/coolant spraying.

A red light flashes when the actuator is pushed, making it easy to see from a distance. They're rated IP65 for protection from washdowns.

Built into a terminal block, these switches mount to DIN rail.

Maximize the space in a panel—these switches are half the size of most toggle switches.

Also known as high-inrush current switches, these switches can handle starting currents up to 10 times greater than their rating, such as when a motor starts.

Able to withstand high currents, these switches are often used with motors and pumps.

Choose from a variety of messages and colored lenses to combine a rocker with a base and wiring socket for a complete switch.

Safe for use in wet locations, these switches are IP and NEMA rated for protection from corrosion, washdowns, and oil/coolant spraying.

These switches withstand temporary submersion.

Control cranes and other mobile machinery in dirty, outdoor, and wet environments without damaging your switch.

Choose an actuator and contact block to make your own 22 mm metal switch.

Turn these switches by hand.

Connect these switches to a cable to control circuits from a distance. They're typically used to turn off production lines and material handling systems. Equipment will not start up again until switch is manually reset.

Activate or deactivate fans, lights, and other devices inside your enclosure when you open or close the door.

Control multiple devices with one switch. Turn the shaft to change switch positions.

The lever sticks out further than a push button, making it easy to identify the position of these switches.

Install these key switches in 30 mm dia. panel cutouts. They require a key to turn circuits on or off, limiting access to sensitive equipment.

These 16 mm switches require a key to turn circuits on or off, limiting access to sensitive equipment.

Delay access to hazardous areas until conditions are safe; use these switches with machines that take time to stop after they are turned off. They mount to a door frame.

Secure sensitive lighting equipment; these switches have a round key that is difficult to duplicate.

Prevent accidental activation—these switches require a key to turn lights on and off.

Also known as three-way switches, these are often used in large, open workspaces and can be wired on opposite ends of the room to control lights on the same circuit.

Press these switches with your foot for convenient, hands-free operation.

Combine a foot-pedal actuator with a switching mechanism to build a complete switch.

Use these switches where ignitable gas and dust may be present. They're rated Class I, Divisions 1 and 2, Groups C and D; and Class II, Divisions 1 and 2, Groups E, F, and G for hazardous locations.

Use these switches to turn motors on and off, or with lighting and electric heat circuits. They do not provide overload protection.

Rated NEMA 4, these switches are protected from washdowns.

Rated IP66, these switches are protected from washdowns.

Mount these switches inside your enclosure to prevent it from opening when power is on—actuating the switch disconnects power and releases the door.

A raintight NEMA 3R rated enclosure protects these switches outdoors.

Rated IP69K, these switches are protected from high-pressure and high-temperature washdowns.