Sectional or telescoping masts on these trucks allow you to lift loads higher than standard lift trucks. Crank the handle to raise and lower loads.

Platforms support material directly without an additional pallet. Pump a foot pedal to raise and lower loads.

Move loads around your facility, then use the hydraulic pump to lift them to a comfortable working height.

Instead of tilting these trucks during transport, push on the handle to lift a drum straight off the ground and move it easily over obstacles. Push the handle down to tilt the drum to dispense.

Fit these compact jacks under low-height loads.

The turning bar gives you leverage to lift heavier loads than wrench-adjustable screw jacks.

A swivel caster lets you reposition your load.

Pump the handle by hand to raise the jack. Turn the release valve to lower the load.

Use these versatile jacks for lifting, spreading, bending, pushing, and straightening.

Push or pry apart material with these rams by attaching them to a hydraulic pump.

Control the flow of oil to adjust ram speed, or shut it off to temporarily hold a load.

Connect up to four rams and a gauge to a pump. Ram connections have flow-adjustment valves to adjust ram speed, or shut it off to temporarily hold a load.

This steel-reinforced hose has male threads.

Connect up to five rams to a single pump.

Use these fittings with hydraulic hose.

These tables have a foot lever and hydraulic pump to raise loads and either a hand valve or hand lever for controlled lowering.

For easy access to material, the tabletop rotates 360° and locks in any position.

Turn the hand wheels to raise the load and tilt it up to 30° for a more ergonomic angle.

These tables have a foot lever and hydraulic pump to raise the load.

Easily grab iron and steel fasteners, small sheets, and other parts from work areas, bins, and hard-to-reach places.

Move large, heavy sheets of plywood, fiberboard, cement board, and drywall with these nonmarring lifters. Unlike suction-cup and magnetic lifters, they will hold porous and nonmagnetic sheets.

For a strong, continuous grip, these lifters have levers to lock them in place.

A long handle gives you the leverage to safely remove manhole covers by yourself.

Also known as engine cranes, a hydraulic hand pump raises and lowers the arm (boom) to lift items without the need for a hoist.

Tackle frequent lifting jobs with these rugged winches—their one-piece machined gears stand up to daily use.

These winches are stainless steel for corrosion resistance. Their one-piece machined gears stand up to daily use.

Move loads more gradually than with other winches. These take longer to wind but require less effort. Their one-piece machined gears stand up to daily use.

These all-in-one lifters include a rubber vacuum cup and a device to generate suction without an installed vacuum system.

With multiple suction ports, these lifters can grip, lift, and move large items with a variety of surfaces.

Grip, lift, and move food as well as other items with curves, angles, and varied heights in food-processing plants. All of these lifters have a flexible balloon-like cup that’s made of FDA-compliant silicone rubber, so they’re safe for direct contact with food.

Lift and move porous, uneven, and delicate items without damaging them.

Use these cups with a vacuum system to grip, lift, and move flat materials, such as sheet metal and plastic.

The oval shape of this cup provides a greater surface area than other cups, so it is good for lifting long, thin objects without bending them.

Pick up long, narrow items in your sanitary facility with these cups—they connect to threaded fittings on your vacuum system.

Thread these cups onto your vacuum system to lift and move sanitary items with curves, corners, and uneven surfaces.

Connect these cups to your vacuum system to pick up bread, pastries, and other soft material.

Prevent oily material from slipping free of the suction with these cups.

These cups have an unthreaded mounting hole to attach to a barbed fitting.

The oval shape of this cup provides a greater surface area than other cups, so it is good for lifting long, thin objects without bending them.

Slide these cups onto unthreaded fittings on your vacuum system to gently pick up bags, plastic film, and other sanitary wrappings.

The bellows on these cups handle items with varied heights and angles better than flat cups.

Connect these pads to your vacuum system to lift and move textured items that standard vacuum cups can’t pick up.

Able to rotate 360° and flex to 45°, these fittings help vacuum cups grip items that are positioned at an angle.

Use in pairs with a two-leg sling to transfer metal plates in a horizontal position. Unlike other plate-lifting clamps, these can pick up multiple plates at the same time.

Pull the on/off handle to engage and release the magnet.

Pads on these clamps prevent the grip from biting into the load.

The ratcheting action makes adjusting these jacks under load easier than screw jack stands.

Adjust the height of a workbench without clearing off the top or loosening leg bolts.

Turn the crank to adjust the height of these tables without clearing off the top or loosening leg bolts. They can be configured for either seated or standing tasks.

Broad, strong Acme threads make these screw jacks better than ball screw jacks for heavy loads, intermittent positioning applications, and where vibration is present.

Add a flat mounting surface to to a screw jack to support loads.

Low-friction ball bearings allow these screw jacks to use half the power required by an Acme screw jack to lift the same load. Typically used as actuators, they run at higher speeds than Acme screw jacks.

Made from stainless steel for excellent corrosion resistance in damp environments.

These general purpose gas springs assist in opening lids, covers, windows, conveyors, and seats—similar to a hatchback opening on a car.

A temperature-resistant seal allows these gas springs to withstand heat up to 392°F.

Automatically locking when fully extended and made of 316 stainless steel to resist corrosion, these gas springs protect material and equipment underneath heavy loads in damp environments.

Ensure you have the correct force for your application. These gas springs have a bleed valve so you can release gas to permanently reduce the force to meet your requirements.

Ensure you have the correct force for your application. These gas springs have a bleed valve so you can release gas to permanently reduce the force to meet your requirements.

Small in size, but not in strength, these gas springs are often used to replace coil springs in metal stamping and die-spring applications.

Sized with short stroke lengths and miniature dimensions, these gas springs are for opening small lids and doors, like those on toolboxes and access panels.

Made from stainless steel for excellent corrosion resistance in damp environments.

These brackets secure eyelet end fittings from both sides to provide a strong hold on gas springs that get bumped or jostled. Mount on any panel, lid, or door.