A 316 stainless steel housing makes these pumps resistant to coolants such as ethylene glycol.

For low-effort dispensing, these pumps have a lever handle that maximizes output with each stroke. Use them to pump lubricating oil, such as motor oil.

All of these pumps have bonding and grounding wires, while some also have an internal flame arrester, to pump fuel, cleaning solvents, and lacquer thinners.

For low‐effort dispensing, a lever handle maximizes output with each stroke. The handle delivers fluid on both the forward and backward strokes to quickly move drum contents.

Remove liquid from hard‐to‐reach areas with a long, flexible intake tube that extends into deep and hard‐to-access tanks.

Often used with ammonia, etching and cleaning solutions, and other caustics, these pumps have a nonsparking air-powered motor for applications where electricity is unavailable or dangerous.

These pumps have a motor that is rated for IEC Zone 1, Groups IIB and IIA; and IEC Zone 21, Groups IIIC, IIIB, and IIIA hazardous locations with flammable gases and vapors, so they can be used with liquids such as acetone, ethanol, methyl ethyl ketone, xylene, and mineral spirits.

Transfer lubricating oil such as hydraulic and motor oil with these pumps. They handle nearly twice the amount of pressure as other air-powered drum pumps to move high-viscosity liquids.

Use these pumps to move lubricating oil such as hydraulic and motor oil.

Pump fuel such as gasoline, kerosene, and diesel fuel.

With a nozzle and hose, these pumps allow you to dispense directly into your container. They move liquid by pressurizing the drum, so they have few moving parts prone to wear and tear.

These pumps quickly empty drum contents by moving 48 gallons of liquid per minute. Their electric motors are UL listed for use in environments with flammable gases and combustible dust.

For accurate dispensing in extremely low-flow applications, these pumps allow you to adjust flow in 2% increments.

Commonly used in food, beverage, pharmaceutical, and cosmetic processing, these pumps are designed for sanitary environments.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

These pumps are C-UL listed for use in environments with flammable gases and combustible dust. Operating on a 12-volt battery, use them to transfer and drain fuel such as gasoline, diesel fuel, and kerosene.

With a 316 stainless steel housing and a PTFE diaphragm, these pumps resist a variety of acids, alkalies, and flammable liquids such as phosphoric acid, acetone, and methyl ethyl ketone (MEK). They're designed for moving large volumes of thick sludges and slurries in demanding environments.

The Santoprene diaphragm resists cracking for a long service life and stands up to water and chemicals such as ammonium hydroxide. These pumps have a rugged aluminum housing for moving large volumes of thick sludges and slurries in demanding environments.

Made of FDA listed materials for use with food and beverage, these pumps have a sanitary quick-clamp fluid connection for easy cleaning. They are commonly used to move sauces, concentrates, and other thick liquids with solids.

The fluoroelastomer diaphragm withstands higher temperatures than a neoprene diaphragm and has better resistance to fuel such as gasoline and kerosene. These pumps have large internal pathways and check valves with flaps to accommodate thick sewage, abrasive slurries, and industrial waste with large solids that would damage standard air-powered transfer pumps.

These pumps have an impact-resistant aluminum housing and handle larger solids than other battery-operated water-removal pumps. Use them to remove water from areas without power.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use the handle to carry pumps from job to job.

Move higher volumes of water than with other high-flow water-removal pumps. These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates.

Built with high-chromium stainless steel components, these pumps stand up to salt water with up to 25% sand by volume and resist wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2” in diameter.

These manual dispensers are more portable than air-powered dispensers.

Add faucets to oil dispensing stations for increased utility.

This dispenser delivers over three times more grease per stroke than our dual-output dispensers.

Mount these pumps to your grease container to bulk load guns.