Use a stud with a base to create non-load-bearing interior partitions and wall framing.

18-8 stainless steel studs have good chemical resistance.

About half the strength of medium-strength steel threaded rods, use these metric fine-thread rods for light duty hanging, mounting, and fastening.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion. About half the strength of medium-strength steel threaded rods, use them for light duty hanging, mounting, and fastening.

These Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

These metric Grade B7 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Grade B16 threaded rods maintain their strength at higher temperatures than Grade B7 threaded rods. They meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Class 12.9 rods are about 20% stronger than Class 10.9 threaded rods and are for use in heavy machinery.

These Class 10.9 steel threaded rods are about 25% stronger than medium-strength steel rods.

Available in metric sizes, these 18-8 stainless steel threaded rods have good chemical resistance.

Grade B8 threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges. They have good chemical resistance.

More corrosion resistant than 18-8 and 410 stainless steel threaded rods, these 316 stainless steel rods have excellent resistance to chemicals and salt water.

Tighten these threaded rods by turning them to the left; once fastened, they resist loosening from counterclockwise motion.

Grade B8M threaded rods meet the pressure and temperature requirements of ASTM A193 and are often used to secure pressure tanks, valves, and flanges.

Bronze threaded rods are stronger and more resistant to salt water than brass rods.

More corrosion resistant than 400 nickel threaded rods, these C276 nickel rods are often used in marine environments and chemical-processing plants.

Titanium threaded rods have a high strength-to-weight ratio and are resistant to acids and salt water.

These metric brass threaded rods are corrosion resistant in wet environments, electrically conductive, and nonmagnetic.

Screw these studs into a tapped hole and use them as a pivot point, hinge, shaft, or locator pin.

Screw the threaded end of these metric studs into a tapped hole and use the unthreaded end as a pivot point, hinge, shaft, or locator pin.

316 stainless steel studs have excellent resistance to chemicals and salt water.

These studs have good chemical resistance. Weld them to stainless steel surfaces.

18-8 stainless steel studs have good chemical resistance and may be mildly magnetic. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

Also known as dowel screws, use these to join two pieces of wood.

These metric 316 stainless steel studs have excellent resistance to chemicals and salt water. Also known as hanger bolts, use them to hang, mount, and fasten parts to wood structures.

These stud anchors strengthen the parts of buildings where steel framing connects to concrete. They’re also known as Nelson studs.

A set of ball bearings reduces friction and secures the end of a metric ball or lead screw.

Internal ball bearings provide smooth low-friction travel in applications that require high speeds, accurate positioning, and repeatable movement. Also known as single-start metric ball screws and nuts, these have a single thread that runs the length of the screw.

Mount these two-piece collars anywhere on an Acme lead screw without removing components.

Keep your ball screw spinning without the ball nut damaging your system. When the ball nut reaches the stop pin at either end of the ball screw, it disengages and begins to idle.

Multiple thread channels (also known as thread starts) create faster linear travel than ball screws with a single thread start.

Also known as single-start ball screws and nuts, these have a single thread that runs the length of the screw. They operate with more torque than fast-travel ball screws and nuts.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

A crisscross thread pattern allows you to drive the nut back and forth without changing the lead screw's direction of rotation. When the nut reaches one end of the lead screw, it changes direction and travels back to the other end.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Install these nuts on a rotary shaft to create a linear positioning system without a lead screw. Instead of threads, a set of angled ball bearings drives the nut along a shaft as it spins.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Attach ball socket end fittings to these studs to mount gas springs.

Suitable for use near sensitive electronic applications, these ball stud mounting brackets are aluminum, which is nonmagnetic.

Pair these 90° angle offset-arm brackets with ball socket end fittings to mount your gas spring in almost any position.

Suitable for use near sensitive electronic applications, these ball stud mounting brackets are aluminum, which is nonmagnetic.

Suitable for use near sensitive electronic applications, these ball stud mounting brackets are aluminum, which is nonmagnetic.

Made from stainless steel for excellent corrosion resistance in damp environments.

A black-oxide finish provides mild corrosion resistance.

These stainless steel anchor studs offer excellent corrosion resistance.

Create a common grounding path for not only internal components and circuits, but also your enclosure’s body.

Attach these hanger studs to a flat surface, then press your insulation sheets onto the spikes and secure with a washer.

These internally threaded linkages have an oil-embedded bronze insert that slowly releases lubricant throughout the life of the joint.

These internally threaded linkages have a slippery PTFE liner that reduces wear and eliminates the need for lubrication.

Able to stand up to frequent use, these linkages offer excellent wear resistance. They consist of ball joint rod ends with a ball stud attached to simplify mounting.

Along with excellent wear resistance, these linkages have a grease fitting for easy lubrication. An internally threaded rod end connects to threaded rods, studs, and other parts with male threads.

A slippery PTFE liner reduces wear and eliminates the need for lubrication.

Use these externally threaded linkages to create inline pivoting connections.

With a ball joint at the top of the shank, these rod ends pivot in the middle of the body instead of in the eyelet. Use them for linear push applications that require movement along the length of the connecting rod.

Also known as tap-end and fixture studs, these rods have friction-fit threads on one end to resist loosening and standard threads on the other side for attaching a nut.