For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a 90° corner for milling square corners in slots, pockets, and edges.

Remove large amounts of material quickly without sacrificing tool life. Variable spacing between flutes reduces cutting time and vibration in high-volume jobs.

Also known as NC tolerance end mills, these carbide end mills have oversize mill diameter tolerances. They're sized to match standard high-speed steel end mills, so you can use them as longer-lasting replacements without changing the size of the cut.

These end mills have a neck that’s extended and has a reduced diameter—this prevents them from rubbing against your workpiece when deep milling.

Get longer life when milling hard material with these end mills—their 10° corner chamfer has a stronger cutting edge compared to standard square end mills.

A titanium-carbonitride (TiCN) coating prevents soft material, such as aluminum, brass, and bronze, from accumulating on the cutting edge and creating an uneven finish.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds without sacrificing tool life.

Cut into the sides and make slots in honeycomb panels without damaging any layers.

Serrations along the cutting edge act as chip breakers, so these end mills can remove large amounts of material at high speeds without sacrificing tool life.

Four flutes with a 35° helix angle provide a smooth finish on nickel alloys, such as Monel, Inconel, and Hastelloy.

Use these end mills for short runs and general purpose milling in most material, such as aluminum, brass, bronze, iron, and steel.

Commonly used to make keyways in rotary shafts, these tools have a -0.0015" to 0.0000" mill diameter tolerance for creating a precise fit.

Use these tools with low-horsepower, manual milling machines. They have clamps for holding inserts that do not have a mounting hole. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

Fasten carbide inserts directly to these end mills for a hold that's strong enough to handle the high speeds of a CNC machine. Replaceable carbide-insert end mills reduce waste and cost in high-volume jobs—when the cutting edges dull, replace the carbide inserts instead of the entire end mill.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as iron, hardened steel, titanium, and tool steel.

A higher helix angle means these end mills clear more chips than other roughing cobalt steel end mills, making them better for milling aluminum, brass, and bronze. Serrations along the cutting edge act as chip breakers, so they can remove large amounts of material at high speeds.

For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. Made of solid carbide, they are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material.

These end mills cut channels with precise angles and dimensions, reducing the need for additional finishing.

These end mills have a diamond or diamondlike coating for machining abrasive material, such as carbon fiber, fiberglass, and graphite.

With a wear-resistant titanium-aluminum-nitride (TiAlN) coating, these end mills provide excellent shearing and chip removal in stainless steel and titanium.

When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

With a higher helix angle than standard high-speed steel end mills, these clear more chips and generate less heat, making them good for milling soft material, such as aluminum, brass and bronze.

Make finishing cuts in tool steel and hardened steel with these cubic boron nitride (CBN) end mills. Harder than carbide end mills, they’re better for making small, precise cuts and last more than five times as long.

With better heat and wear resistance than high-speed steel, these cobalt steel end mills can run at higher speeds and provide better performance on hard material, such as iron, hardened steel, titanium, and tool steel.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Their angled profile allows chamfer, bevel, and other angled cuts.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life on hard materials.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. The teeth are angled on both sides so you can make top and bottom chamfer cuts without having to flip the workpiece.

Use these versatile end mills for milling in most material, including aluminum, brass, bronze, iron, and steel. Also known as taper degree end mills, they're often used to machine angled slots in dies and molds.

These tools have a tapered profile and rounded cutting edge for making smooth contours on intricate, three-dimensional shapes. They're also known as taper degree end mills. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

When one end wears out, switch to the opposite end for two times the life of a standard carbide end mill. Made of solid carbide, these end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel for the longest life and best finish on hard material. Use them to round sharp corners on the edge of your workpiece.

Use these versatile end mills for milling in most material, including aluminum, brass, bronze, iron, and steel.

Use these end mills for general purpose keyseat cutting in a wide range of material, including aluminum, iron, and steel. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

With better heat and wear resistance than high-speed steel, these cobalt steel keyseat cutters can run at higher speeds and provide better performance on hard material. They mill precise notches in rotary shafts to fit machine keys and can also be used for slot milling.

Create dovetail grooves that allow O-rings to flex without falling out of place.

Use these versatile end mills for milling in most material, including aluminum, brass, bronze, iron, and steel. They create dovetail slots for connecting two components with a sliding fit.

For longer tool life and a better finish in general purpose milling applications, these solid carbide end mills are harder, stronger, and more wear resistant than high-speed steel and cobalt steel end mills. Often used for slotting and pocketing cuts in mold and die making, these end mills have a 90° profile and rounded corners, which reduce flute breakage and chipping.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life. They have a high helix angle and a wear-resistant coating for excellent shearing and chip removal in stainless steel and titanium.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life on hard materials.

Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life.

Replicate the shape of complex parts with these end mills.

With a diamondlike coating (DLC), these end mills are sharp enough to cut aluminum, brass, and bronze.

Made of solid carbide, these end mills are harder, stronger, and more wear resistant than cobalt steel for the longest life and best finish on hard material. A 90° pointed tip allows them to be used for drilling as well as for slotting, profiling, chamfering, and spotting cuts.

Use these versatile end mills for milling in most material, including aluminum, brass, bronze, iron, and steel. They're often used to create slots in machine tool tables, indexing tables, and other workholding surfaces.

Use these end mills for general purpose work in most material, such as aluminum, brass, bronze, iron, and steel. With curved, side-cutting teeth, they create hollow, inward-curving grooves.

A titanium-diboride (TiB2) coating reduces friction when working with nonferrous metals, so you can use these end mills to cut soft metals like aluminum, brass, and bronze. Variable spacing between the flutes reduces vibration, allowing these end mills to provide fast cuts, smooth finishes, and long tool life.

With larger diameters than end mills, these cutters remove greater amounts of material to create a smooth, flat channel in the face of a plate, bar, or other wide workpiece.

These kits include a cutter body, inserts, wrenches, and screws, so you can create your own face milling cutters, which are also known as indexable face milling cutters.

These general purpose saws are good for cutoff, slitting, and slotting applications in a wide range of materials, including aluminum, iron, and steel.

With peripheral and side teeth, these saws remove chips for a consistent cutting width.

The end mills in these sets have one milling end and a standard shank. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

For general purpose milling in most material, the end mills in these sets have one milling end and a standard shank.

Keep a variety of fly cutters on hand to tackle different sized workpieces. The fly cutters in these sets hold a lathe tool (sold separately) to shave a layer off your workpiece with each pass, creating a smooth, even finish.

Offering two times the life of a standard carbide end mill, the end mills in these sets have two milling ends so you can switch to the opposite end when one end wears out. Made of solid carbide, they're harder, stronger, and more wear resistant than high-speed steel for the longest life and best finish on hard material.

With a tilting, rotating table, these milling machines create more complex shapes than 3-axis models without requiring multiple setups. By moving the spindle and rotating the workpiece simultaneously, they’re capable of making helical gears, manifolds, and other small parts that require 3D contouring, hollowing, and undercutting.