Mount to a surface and add a cable tie to secure a bundle.

Often used to secure vertical running material, these mounts maintain space between a bundle and a surface.

For use in environments subjected to chemicals, these mounts withstand the most corrosive conditions.

Use these mounts with stainless steel cable ties when working in corrosive environments.

Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage.

Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers.

Bolt directly to a pipe flange to suspend a run of pipe above the ground.

A mounting plate provides a more secure hold at the mounting surface.

Combine with a U-bolt or routing clamp to convey a variety of material, such as pipe, tubing, and cable raceway, at distance from floors, walls, and ceilings. The extra clearance allows access for maintenance and adding and removing lines.

An interlocking steel frame in these mounts prevents collapse, even if the rubber fails.

Limit damage during moderate earthquakes.

Connect these mounts to your air supply for vibration and shock isolation in compression load applications.

The polyurethane base on these mounts resists solvents, gasoline, and oil, while the metal plate sustains heavy loads.

Made of neoprene rubber, these mounts are oil resistant, so they're good for use under generators, HVAC equipment, electric motors, pumps, and blowers.

Specifically designed for light vertical loads, these mounts buckle to protect lightweight equipment such as small fans and pumps from vibration.

These mounts withstand exposure to weather and resist oil, antifreeze, and other petroleum-based fluids.

A two-piece design makes these mounts easier to install than one-piece mounts.

Made of tightly layered stainless steel mesh, these mounts withstand temperatures up to 500° F.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Well-suited to damp environments, these metric mounts have a stainless steel stud and nut for corrosion resistance.

An offset mounting hole allows for installation without moving your machine.

Broader, stronger threads enable faster adjustments and higher load capacities than standard V-shaped threads.

Made of yellow zinc-plated steel, these metric leveling mounts are more corrosion resistant than nickel-plated steel leveling mounts.

Nickel-plated steel has some corrosion resistance.

Made entirely of 316 stainless steel, these mounts have superior corrosion resistance.

Yellow zinc-plated steel is more corrosion resistant than nickel-plated steel.

Black-oxide steel has a dull shine for areas where appearance is a concern.

An economical choice for applications in corrosive environments that don't require high load capacities, these mounts have a plastic base.

Made of 303 stainless steel, these mounts resist corrosion from water and most chemicals.

Punch-out holes in the base let you bolt down these mounts to keep your equipment stationary.

Install these mounts on machines without feet.

Able to withstand temperatures up to 350° F, these have the highest maximum temperature of our plastic mounts.

Made entirely of plastic, these mounts are resistant to oil and won't scratch your mounting surface.

Protect surfaces from scratches and wear.

Often used on wobbly tables, these mounts automatically adjust up to 5/16" to compensate for uneven floors.

A shield on the stud prevents dirt accumulation on the threads and provides a finished appearance.

All-stainless steel construction stands up to water and chemicals and won't rust or corrode.

Higher deflection ratings translate to greater vibration and shock isolation than our other vibration-damping leveling mounts.

Choose from mounts that support 3,000 to 30,000 lbs. for heavy machinery.

Thread these mounts into machinery to level them on uneven floors in sanitary environments such as food-processing areas.

Higher deflection ratings translate to greater vibration and shock isolation.

Cover the bottom of furniture legs.

Screw these feet to the bottom of wood furniture legs.

Place these feet under furniture and equipment.