No need to tighten or loosen any screws—these terminals lock your wiring in place with spring clamps.

One of the connections on these terminal blocks is a socket instead of a traditional terminal, making it easy to swap out equipment or change your wiring even in small enclosures. Instead of having to attach wire inside the tight space of your enclosure, you can wire a connector wherever it’s easiest and then plug it into the socket.

Mount blocks to a panel or the surface of a machine. Also known as barrier terminal strips.

The spring-clamp terminals on these blocks make wire installation faster than other types of terminals. These wire connections also stand up to vibration and temperature changes.

Made of ceramic, these blocks withstand high-temperature applications that reach up to 1110° F such as ovens and furnaces. They have recessed screws to reduce the chance you’ll cause a short by accidentally connecting two circuits with a screwdriver or other tool.

Customize these blocks’ wiring as your application changes. They come with jumpers that connect terminals on the same block, either across or next to one another.

Save time when wiring connections in a junction box; these blocks come already installed in an enclosure.

With the help of distribution blocks, you can take a high-current wire from your power source and connect it to one or more electrical devices.

Build your own distribution system by adding terminal blocks to these bars.

Often used in offices and workstations, these outlet strips power multiple devices from a single wall outlet.

The power switch to these outlet strips is on a 44" long cord, so you can control power even when the strips are in hard to reach places, such as under a desk.

Keep personnel safe from electric shock with ground fault protection.

Also known as hospital-grade outlet strips, these outlets have an extra-tight fit to prevent plugs from detaching. They are marked with a green dot.

With a rubber housing, these outlet strips withstand drops and other impact.

Connect multiple devices from a single outlet.

Mount these strips into standard 19" wide electronics racks and enclosures.

Bring power to workstations that are not near a wall—these poles mount from the ceiling.

Power multiple devices with one extension cord.

Insulated to resist water, oil, and solvents, these cords withstand dirty and greasy environments.

Connect additional USB ports to your computer.

Extend the reach of USB devices.

Send video and audio from a single DisplayPort output to multiple displays. These splitters are often used to show the same image on multiple screens or to stretch a computer desktop across two monitors.

Distribute air or fluid to multiple locations from a single supply source with these manifolds. They are also known as headers.

These manifolds have two separate sections inside, so you can run two different substances through them without worrying about them intermixing. Also known as headers.

When you’re short on vertical space, these manifolds are a good fit—they have outlets on the side instead of on top, so they have a lower profile than rectangular manifolds. Use them to distribute air or fluid to five locations from a single supply source.

Mount these manifolds on the end of a hose line to distribute air, water, or hydraulic fluid to three locations from a single supply source.

Use these manifolds with molding equipment to circulate hot and cold water through your line. They have a red side for hot water and a blue side for cold water.

Use these junction blocks to organize and separate multiple lines in your system. They have threaded holes that allow air or fluid to flow straight through the block.

These fittings won’t absorb moisture, so they’re good for water and high-humidity air applications.

Made of nickel-plated brass, these fittings have better corrosion resistance than unplated brass fittings.

Use at pressures up to 250 psi.

The smooth finish inside these stainless steel quick-clamp fittings makes it easy to remove product residue.

Build a custom 1/4" system to deliver coolant, cutting oil, water, or air in any direction.

Build a custom 1/2" system to deliver coolant, cutting oil, water, or air in any direction.

Use with Snap-Loc hose to assemble and disassemble components.

Use with manual and electric pumps to dispense different amounts of oil from multiple lubrication points.

With a maximum flow of 0.005 oz. per cycle, these pumps deliver small, precise amounts of oil. Turn the dial to set the cycle interval.

Connect these modular pumps to a reservoir and a solenoid valve to automate the flow of oil.

Serve multiple lubrication points from a single location.

Customize these dispensers to serve up to 24 lubrication points from a single location.

A sealed design prevents contamination in dirty and dusty environments.

Connect these dispensing stations to your bulk oil container to easily fill hand-held dispensers.

Connect these modular pumps to your air system and add a solenoid valve to automate the flow of grease.

Connect two or more of these manifold regulators to meet multiple pressure requirements from a single air supply—set a different output pressure with each regulator.

Use a single air supply to meet the pressure requirements of multiple applications—connect one of these manifolds to your air line, and then set a different output pressure for each station.

Use a single air supply to distribute air to up to four locations. In addition to the outlet for inline connection, these manifolds have three 1/4 NPT female outlets for connection to air-powered tools and equipment.

Monitor refrigerant pressure with analog gauges when servicing air conditioning systems.