Nonconductive and softer than brass, the nylon tip reduces vibration and eliminates damage from metal touching metal.

Made from nylon, these metric pan head screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Reliable in harsh environments up to 500° F, PEEK screws withstand acids, bases, and salt solutions. They are chemical and oil resistant, nonconductive, and lightweight.

Made from polycarbonate, these metric pan head screws resist breaking in high-impact applications. They are chemical and oil resistant, nonconductive, and lightweight.

Made from nylon, these metric screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

These metric PTFE screws withstand harsh chemicals and temperatures from -100° F to 500° F. They are nonconductive, lightweight, and resist wear due to their slippery surface.

Nylon screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

Made from nylon, these screws are chemical and oil resistant, nonconductive, and lightweight.

Ceramic screws won't melt, rust, seize, or become brittle—even at extreme temperatures. They are nonconductive and highly resistant to corrosive gases.

These screws are chemical and oil resistant, nonconductive, and lightweight. The flange eliminates the need for a washer, distributing pressure where the screw meets the surface.

These metric screws are chemical and oil resistant, nonconductive, and lightweight. Exposure to moisture may cause them to expand.

These metric polycarbonate screws resist breaking in high-impact applications better than other plastic screws. All are chemical and oil resistant, nonconductive, and lightweight.

These screws are more reliable in high-stress, high-temperature environments than other plastic screws. They withstand water, steam, and temperatures up to 500° F.

Made from 18-8 stainless steel, these screws are chemical resistant.

The neoprene-backed washer seals out contaminants.

Made from nylon, these set screws are lightweight, resist chemicals, and won’t carry an electric current.

These chemical-resistant 18-8 stainless steel screws have an extra-soft nylon tip, which minimizes the damage that can occur from metal-on-metal contact. Use them on soft surfaces such as aluminum.

These alloy steel set screws have an extra-soft nylon tip, which minimizes the damage that can occur from metal-on-metal contact. Use them set screws on soft surfaces such as aluminum.

These metric thumb screws have a knurled head for a slip-resistant controlled adjustment.

A large head allows you to grip these screws with your entire hand for greater torque while tightening than standard knurled plastic-head thumb screws.

Tighten these thumb screws by hand or with a hex key for more torque.

A soft nylon tip conforms to textured surfaces and minimizes damage when holding items in place.

Stronger than standard nylon, these thumb screws are chemical resistant, nonconductive, and lightweight. They have a raised head that makes them easy to grip.

A thin head allows these thumb screws to be used in low-clearance applications.

Plastic binding barrels and caps are chemical resistant, nonconductive, and lightweight.

Rivet these wing head nuts into thin panels for a flush fit. They can be mounted without space between panels. A quarter-turn locks and releases access panels, doors, and covers.

These wing-head screws have a clip-on nut that allows you to mount them near the edge of a thin panel. Use them to lock and release access panels, doors, and covers with a quarter-turn.

Push the plunger to secure and pull to release for quick access.

These metric threaded rods are made from nylon 6/6 and resist oil, grease, and solvents. They’re nonconductive, making them good for use around sensitive electrical components.

PTFE threaded rods withstand temperatures up to 250° F and resist oil, grease, detergents, and most mineral acids. They're the lowest friction plastic threaded rods we offer, so they thread on smoothly.

PVC threaded rods resist acids, alkalies, salt solutions, and alcohol.

Also known as mungo anchors, these have large fins that prevent rotation.

These anchors are also known as drive rivets. To install, hammer the screw into the body. Unthread the screw to remove.

Fins prevent these anchors from spinning during installation.

Retract the nose by pulling the knob.

Identify equipment controls and components at a glance by their color. Mount these knobs into a threaded hole. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Bonded to the stud is an acrylic adhesive that adds friction to resist loosening from vibration. Use these knobs to position, tighten, and hold fixtures, equipment, and machinery. They mount into a threaded hole.

Knobs have left-hand threads; they're used in applications where counterclockwise motion can loosen common right-hand threads. Mount them into a threaded hole to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom knob or thumb screw, pair one of these knobs with a hex or socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Use these knobs to display important messages. To build a custom knob or thumb screw, pair one of these knobs with a socket head screw. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

Install these knobs on a threaded stud. They provide a secure grip to position, tighten, and hold fixtures, equipment, and machinery.

To build a custom precise-control knob or thumb screw, pair one of these knobs with a socket head screw. Turn the knob to move the screw 0.005" per graduation and make precise adjustments.

Create custom threads to secure these handles to the front of your surface from the backside. Use them to open and close a variety of doors and drawers, including those on furniture, machines, and equipment.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Multiple thread channels (also known as thread starts) create faster linear travel than lead screws with a single thread start.

Also known as single-start and self-locking lead screws and nuts, these have a single thread that runs the length of the screw. The nut travels only when the screw turns, so your system won't unexpectedly move when the lead screw is at rest.

Use these eyebolts for routing wire and for other light duty applications.

Sized to fit hex nuts, these caps snap on for a tight hold and provide protection from corrosion.

To conceal and protect the entire screw head, insert your screw through the hole in the base and snap on the top.