For a long-lasting cutting edge that's three times harder than uncoated stainless steel, the blades on these scissors are titanium bonded over stainless steel.

Minimize hand fatigue with a lightweight handle and spring-action that automatically opens the blades for quick repeat cuts.

Longer handles and shorter blades give you more leverage than other scissors to cut tough materials such as leather, rope, and thick cardboard.

Minimize hand fatigue—the handles on these scissors are lightweight and spring-action opens the blades for quick repeat cuts.

For extra leverage to cut through tough materials such as leather, rope, and thick cardboard, these scissors have long handles and short blades.

Prevent snags and injury with the rounded points on these small scissors.

For extra leverage to cut through Kevlar, metal, and plastics, these scissors have long handles and short blades.

With high-carbon stainless steel blades, these scissors cut through fiber-optic and electrical cables, even those that are made with Kevlar. They’re also good for cutting wire jackets and cable ties.

Also known as electricians' shears, the back edge of the blade has a file to clean contacts.

A double hinge provides high cutting force with low gripping pressure. These cutters are also known as aviation snips.

Blades are high-speed steel so they stay sharp longer than steel blades, and they can be sharpened.

This cutter has two blades that cut a 13/64" wide strip—peel it back for smooth edges with little distortion.

These cutters make straight cuts and curves.

Blades are tapered to give you more control when cutting straight lines, tight curves, and circles, and they're serrated to prevent slipping. These cutters are also known as duckbill snips.

Made from aluminum bronze, the blade and handle on these cutters inhibit sparking and are FM approved. Use them for straight cuts.

Handles are angled to keep your hand away from the material as you cut straight lines and curves.

A double blade creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Punch small pieces out of material to create an almost burr-free cut with no material distortion.

Also known as slotting shears, these cutters have a double blade that creates two cuts and a 7/32" wide waste strip that peels back, leaving two smooth edges with little distortion.

Also known a scissor-blade shears, the bottom blade remains stationary while the upper blade moves up and down to cut metal up to 1/64" thick with minimal material loss and edge distortion.

Make straight, clean cuts in thick sheet metal.

This large-capacity cutter has a 25" blade for long, straight cuts.

Combine the cutting base and a corner punch to make rounded corners in sheet metal.

Leave clean cut edges in a variety of pliable materials.

Cut straight lines and patterns with the rotary blades on this cutter.

Good for high-volume cutting and trimming.

Produce clean, distortion-free cuts in cable with one-handed operation.

Use these one-handed cutters on small-diameter aluminum and copper power and communication cable.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface.

Precisely position and flush-cut copper, gold, silver, and magnetic wire.

A double hinge provides high cutting force with low gripping pressure.

Plastic-cushioned grips make these cutters easy to hold during repeated cuts.

Cut thin, hard wire with these small cutters.

Make repeated cuts in hard materials with cutters that mount for stability and provides extra leverage.

Cut medium steel chain and hard steel bolts, rods, screws, rivets, nails, bars, wire, and rebar.

Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505.

Handle is angled 30° to keep work in sight and hands clear of the work surface. Blades are flat on one side for close-to-the-surface cuts.

Minimize material distortion while cutting steel and stainless steel wire rope.

Cutters have double hinge that provides high cutting force with low gripping pressure.

A small grip enables one-handed cutting.

With a quick hammer blow, these cutters make cuts without squeezing or flattening wire.

An alternative to hacksaws and bandsaws, these cutters use leverage to cut rods cleanly in a single stroke.

Cut plastic and rubber pipe, tubing, and hose.

Fit this compact cutter into your pocket or tool belt.

Also known as diagonal-cutting pliers.

These cutters are stainless steel, which provides excellent corrosion resistance.

These sets include four cutters, each with a different head shape.

These tools divert static electricity faster than our other static-control wire cutters.

The specially designed internal spring provides constant, uniform tension for superior performance.