We will reply to your message within an hour.
More
Create threads in hard-to-work areas—where you can’t reach the back of a workpiece, or material is too thin to be tapped.
A smooth base provides more contact with the mating surface than weld nuts with projections.
Projections on the base concentrate the weld and provide room for heat to dissipate.
These nuts can be used in channels and tight spaces where round-base weld nuts won't fit.
Use these metric nuts in channels and tight spaces where round-base weld nuts won't fit.
Weld these nuts to stainless steel surfaces.
Weld these nuts to uncoated steel surfaces.
Square weld nuts have more weld points than hex weld nuts for a stronger hold. Use them on flat surfaces.
Weld these nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.
Weld these metric nuts to flat and uneven uncoated steel surfaces for a strong permanent hold.
You can weld these nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.
You can weld these metric nuts to flat and uneven uncoated stainless steel surfaces for a strong permanent hold.
A smooth base on these metric nuts provides more contact with the mating surface than weld nuts with projections
Threads float inside the retainer so you can install a bolt at a slight angle to align with off center parts.
Threads float inside the retainer of these metric nuts so you can install a bolt at a slight angle to align with off center parts.
These nuts have three mounting holes to accept screws and rivets for use with thin materials.
These screw-mount nuts are often used to attach glides and levels to wood.
Stainless steel adhesive-mount nuts have excellent corrosion resistance in most environments.
These adhesive-mount nuts have a zinc plating for corrosion resistance in wet environments.
Also known as U-style clip on nuts, these nuts have a barrel with multiple threads for secure thread engagement.
These metric nuts have a barrel with multiple threads for secure thread engagement. Also known as U-style clip-on nuts.
Use these light-duty clip-on nuts in low-clearance applications.
The S-style design provides more strength than other no-slip clip-on nuts.
A hex- or square-shaped barrel allows these clip-on nuts to be gripped with a wrench to hold them in place when tightening a screw. They have multiple threads for more thread engagement than low-profile clip-on nuts.
A hex-shaped barrel allows these clip-on nuts to be gripped with a wrench to hold them in place when tightening a screw. They have multiple threads for more thread engagement than low-profile clip-on nuts.
These nuts firmly clip onto the edge of panels and stay secure.
These nuts are often used to secure parts on electric consoles.
Slide these nuts on the edge of a panel and position them by hand. Also known as G-style clip-on nuts.
Also known as G-style clip on nuts, slide these nuts on the edge of a panel and position them by hand.
Snap these nuts into square holes in thin materials.
Stainless steel snap-in nuts have excellent corrosion resistance in most environments.
These nylon nuts are chemical resistant, nonconductive, and lightweight.
The most corrosion resistant tee nut inserts we offer, these inserts stand up to chemicals and salt water.
Steel inserts have high strength for durability.
These 18-8 stainless steel tee nut inserts have better corrosion resistance than zinc-plated steel tee nut inserts.
Ridges on the barrel of these inserts make them less likely to split hardwood than inserts with prongs. They're often used in wood that has been cut across the growth rings.
Six prongs around the barrel of these inserts provide a strong hold and prevent them from loosening and twisting.
Fewer prongs than other tee nut inserts reduce the risk of splitting hardwood—these inserts have three short prongs.
Hooked prongs give these inserts excellent holding power even when removing screws.
Use where vibration is a concern—these tee nut inserts have distorted threads that lock screws in place.
A wide flange distributes the load over a large area. Hammer these inserts into a drilled hole.
Screw and nut sets or nuts secure brackets and other accessories to rails.
Build test fixtures, prototypes, and other small structures with this miniature version of T-slotted framing and fittings.
Fasten these brackets to ceilings, walls, beams, and joists to hang threaded rod.
Add a mounting plate to your U-bolt for a more secure hold at the mounting surface.