We will reply to your message within an hour.
One head is angled 60° for access to hard-to-reach fasteners. These are also known as ignition wrenches.
These wrenches are made of stainless steel for excellent corrosion resistance.
These lightweight tools are also known as AN (Army-Navy) wrenches.
Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
The slim head fits into tight spaces and around thin fasteners.
These are also known as tappet wrenches.
One head is angled for access to hard-to-reach fasteners. These are also known as ignition wrenches.
The opening shape makes more contact with fasteners for a better grip than standard open-end wrenches. These tools are also known as flare-nut or line wrenches.
Sized for working on small equipment, these wrenches are 4 1/8" long with a slim head and handle.
When turning fasteners in small spaces, these short wrenches fit where others can't.
A ratchet mechanism in the heads lets you turn fasteners in tight spaces without removing and repositioning the wrench.
Strike the handle with a hammer to break stuck fasteners free. These are also known as slugging wrenches.
The head is offset 45° to provide additional clearance when reaching over obstructions.
Also known as spud, structural, and construction wrenches, use the pointed end of the handle to align bolt holes during assembly.
Also known as alligator wrenches and water-meter nut wrenches, the V-shaped head fits multiple hex fastener sizes.
Made of stainless steel, these wrenches have excellent corrosion resistance.
Fit the narrow head into tight spaces and around thin fasteners.
The slim heads fit into tight spaces and around thin fasteners.
One head is angled 75° for access to hard-to-reach fasteners. These are also known as ignition wrenches.
Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present.
When working in tight spaces, these short wrenches fit where others can't.
An extra-long handle provides access to hard-to-reach fasteners and increases leverage.
Flip these wrenches over to ratchet in the opposite direction.
A lever reverses the ratchet direction.
A spline-shaped box end turns spline, hex, and 12-point fasteners. This shape also gets a better grip on rounded fasteners that can be difficult to turn with a traditional wrench.
Pivot the box end for access to fasteners in tight spots.
Suitable for occasional maintenance work, these sets are imported.
Made in the U.S.A., these tools handle the toughest industrial applications, provide the best grip on fasteners, and have a superior finish.
Quickly find the wrenches you're looking for with these brightly colored sets.
Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.
Often used with an extension, these sockets turn fasteners and fittings in obstructed areas that a regular socket can't reach. They are also known as crowfoot wrenches.
The opening shape makes more contact with fasteners for a better grip than standard open-end sockets. Also known as flare-nut or line wrench sockets, they're often used with flared tube fittings and fuel and hydraulic lines.
The jaws on these wrenches are shaped to turn slip nuts, jam nuts, and large hex nuts.
Fit the thin head and long jaws into narrow spaces.
A plastic-covered handle provides a comfortable grip.
Press the lever to lock the jaw and keep these wrenches clamped on your work, leaving your hands free.
The adjustment knurl won't turn when the wrench is being used, preventing accidental loosening of the jaws.
The handle is covered in plastic for a comfortable grip.
An insulated handle protects against accidental contact with live electrical circuits. These wrenches are tested to 1,000 volts to meet IEC 60900.
These tools have the heavy duty handle and adjustment mechanism of a pipe wrench and the smooth jaws of a traditional adjustable wrench.
Extend the handle for additional reach.
Also known as a basin wrench, this tool has a pivoting head and spring-close jaws for working in tight spaces where it’s difficult to adjust a traditional wrench.
Turn fasteners with the firm grip of a wrench and the adjustability of pliers.
Squeeze the handles and the gripping surfaces adjust to fit your fastener and prevent slipping and stripping.
A ratchet mechanism in the head allows you to turn fasteners in tight spaces without removing and repositioning the wrench.
Flip the wrench over to use the raised section on the head as a hammer.
Reverse the movable jaw to convert from a smooth-jaw adjustable wrench to a serrated-jaw pipe wrench.
Also known as spud, structural, and construction wrenches, the pointed end of the handle aligns bolt holes during assembly.
The handles are covered in plastic for a comfortable grip.
Change heads to use these tools as an open-end, box, square drive, or hex-key wrench.
Lock wrenches into these racks before taking them with you. Snap tools into the slots and twist one wrench to lock or unlock the whole set.
Hold and carry wrenches on both sides of these caddies.
Set on a benchtop or mount with screws.
Mount to walls, cabinets, and other steel surfaces.
Tabs hold wrenches in place.
The slots in these low-profile organizers are a different color than the base so it's clear when tools are missing from your bench top or drawer.
Organize your tool drawer by positioning these low-profile rails to accommodate wrenches of any length.
Pivot the socket end to access hard-to-reach fasteners.
These wrenches have one pivoting socket end and one open end.
The head pivots to accommodate a range of diameters.
In addition to a long handle, these wrenches include two heads with different hook widths.
Fit these wrenches into slots on the circumference of collars, bearings, and other machine tool components.
Sets include various sizes of wrenches that fit into slots on the circumference of collars, bearings, and other machine tool components.
These wrenches are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.
Sets include various sizes of wrenches that are shaped to fit round holes on the circumference of collars, bearings, and other machine tool components.
Change out the pins to fit a different hole size.
The slim profile fits the flanges and nuts on the backing pads of portable sanders and grinders.
Reverse the pins when you need to fit different hole sizes on the face of collars, bearings, and other machine tool components.
Hinged for adjustability, these wrenches fit a range of diameters.
Use your ratchet wrench as a handle.
Grip the round holes on the face of collars, bearings, and other machine tool components.
Multiple contact points grip the grooves on plastic water filter housings for loosening and removal.
Made of spark-inhibiting materials, these wrenches are also corrosion resistant.
Also known as bung wrenches, these tools are used to install and remove screw-in drum plugs.
Instead of carrying around a large drum plug wrench, keep these sockets in your toolbox and turn with a ratchet wrench.
When the set torque is reached, these wrenches slip to disengage and stop overtightening.
Turn valve stems, nuts, and caps on welding tanks.
Insert into a pipe or fitting and turn—the wrench grips the walls for easy installation and removal without marring the outside of the pipe.
Also known as monkey and auto wrenches, these grip large fasteners and other flat objects.
The jaws grip most round surfaces, even highly polished objects. Push down on the wrench and pull the handle toward you—the jaws will tighten around the workpiece.
Made of aluminum-bronze that is Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant. They are also known as railroad wrenches.
Use one end as a traditional pipe wrench and the other to loosen valve wheels. These are also known as engineers’ pipe wrenches.
There's no adjustment nut or button on these wrenches—a spring-loaded hinge automatically closes the top jaw around pipe.
Made of materials that are Factory Mutual approved, these wrenches inhibit sparking and are nonmagnetic and corrosion resistant.
Open and close the jaws with one hand. Press the lever and slide the bottom jaw to the desired position; tension keeps it in place.
Grip pipe and conduit as well as tighten and loosen fittings.
Replace nuts on pipe wrenches.
Replace springs in pipe wrenches.
Turn the end of the handle to set torque, and the wrench makes an audible click when it reaches the setting.
Turn off the main supply of water or gas at the point it enters your facility.
Install and repair sink drain traps and fittings.
In addition to standard and pop-up sink drains, these wrenches install and remove overflow outlets and toilet inlet connectors (also known as spuds).
Turn the lugs on fire hose fittings and the fasteners on hydrants.
A spanner-style head fits the lugs on fire hose couplings and adapters.