Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

No need for wiring—these lights plug-in with a three-prong plug.

Hardwire these lights to a power source.

Illuminate paths, driveways, and other areas that don’t have a power source without running wires underground.

These lights are UL listed for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

See what’s happening outside your facility—day and night. These lights have a built-in video camera that records when they sense motion.

Guide pedestrians and drivers at night with lighting that defines paths and driveways. These lights produce ambient illumination without the glare of overhead lights.

The enclosure on these jelly jar lights contains explosions, sparks, and flashes. These lights are safe to use in NEC Class I, II, and III, Division 1 hazardous locations.

Built for hot, hazardous areas such as steel mills and refineries, these lights work in temperatures up to 212° F. Rated NEC Classes I and II, they’re safe to use where there are ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Mount these lights in recessed spaces so the lens is flush with the ceiling or wall. NEC Classes I and II, they’re safe to use in paint spray booths, blast booths, and other areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust.

Contain explosions, sparks, and flashes—the enclosure on these ceiling lights makes them safe to use in NEC Class I and II, Division 1 hazardous locations.

Tough enough for offshore rigs and seafaring vessels—yet less than half the height of typical jelly jar lights. Built with a thick aluminum housing and a tough polycarbonate lens, these lights withstand hard impact without a guard.

Light up spaces that have no electrical connection or are difficult to wire, such as sheds and closets.

Install these lights flush with your ceiling for a smooth look and even lighting. They offer the appearance of can lights without the bulky housing.

Install these lights into ceiling cutouts with housings for direct, overhead lighting. They’re often used in indoor spaces such as offices and lobbies, and as decorative lighting.

Upgrade your old fixtures to energy-efficient LED lights. These kits replace the need to maintain hard-to-find-bulbs and ballasts, or replace the entire fixture.

Powered by the sun, these lights illuminate outbuildings, shipping containers, and other remote places that lack electricity.

Brighten entryways and small spaces.

Wire these lights end-to-end to create long rows that brighten indoor workspaces such as offices and workshops.

Create long rows of lights in indoor workspaces without having to hardwire one unit to another.

Often used in stairwells and hallways, these lights save energy by only turning on when they sense movement.

Illuminate steps to reduce the risk of tripping or falling, especially at night or in poorly lit areas.

Rated for over a decade of use well above 100° F, these linear bay lights long outlast standard facility lights in high heat.

Illuminate harsh, wet areas, even outside in extreme weather—these lights are often used on ship building ports. Rated NEMA 4X and UL marine listed, they’re sealed against heavy rain and washdowns, and they won’t corrode from salt water or other liquids.

Upgrade your traditional fluorescent washdown lights—these LEDs last longer and eliminate the need to replace bulbs.

Also known as troffers, these lights fit flush into most drop-ceiling grids. They’re fully sealed with an airtight gasket, so they’re rated IP65 for protection against low-pressure washdowns, humidity, and dust.

Prevent contaminants from entering your ISO Class 3 clean room—these lights have an airtight seal.

Light up large, open rooms where you need a quick setup and takedown, such as a room under construction. Just hang these lights from a ceiling up to 30' high and they’re ready to go.

Pop these lights on magnetic surfaces to brighten wet spaces. Rated NEMA 6 and ETL listed, you can splash, spray, or dunk them in water, and they’ll keep working.

Power these lights with the same battery as your other cordless tools. They run on a Milwaukee M18 battery to light up work where there’s no outlet.

From pipes to pallet racks to control panels—these lights clamp onto almost anything and swivel to direct light just where you need it.

Splashes and drips are no problem for these lights. They don’t need an outlet, so you can bring them wherever you need them.

Flood hazardous areas with light—these lights are intrinsically safe, meaning they can’t cause an explosion or fire. Rated NEC Class I, II, III, and Zone 0, they’re safe to use in areas with ignitable concentrations of flammable or combustible gases, dust, and fibers.

Safely light up large spaces where combustible gases and dust are normally present. Rated NEC Class I and II, these lights have a housing that contains any sparks or flames and seals out ignitable gases, vapors, and dust.

Flood dark, remote jobsites with multiple tiers of light. These cordless lights stack on top of each other to focus a strong beam of light in one direction.

Brighten remote areas, even if they’re damp or rainy. These floodlights are IP rated to keep out humidity and dripping, splashing, and falling liquids.

Compact and easy to carry, these ETL listed lights stand up to dripping, splashing, and falling liquids. The head adjusts up and down to direct light where it's needed.

Raise, lower, and tilt these lights to brighten your work in wet spaces.

Brighten remote spaces with the DeWalt rechargeable battery that’s already in your toolkit. These floodlights extend up to 7 ft., and the light head turns at any angle to aim light where it’s needed.

As bright as stadium lights, these floodlights are the most powerful in our offering—they’ll brighten jobsites half the size of a football field. They run on a diesel generator you can use to power other lights and tools in the field.

Light the path toward exits where combustible gases and dust are constantly present—the enclosure on these lights contains sparks and flashes to prevent a reaction with nearby hazards. They’re often found in extreme environments, such as refineries and chemical plants.

Expand the reach of emergency backup lights. These add-on heads are often used to extend emergency lighting into stairwells, exits, and other remote areas.

Install these lights in aircraft hangars, gas plants, and other facilities where flammable and combustible gases or dust may be present, such as leaks or ventilation failures. Rated NEC Class I, Division 2, they seal out gases but aren't built to contain explosions.

Gooseneck arms can be repositioned faster and more easily than articulating arms.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

With a smooth, shatterproof lens, these lights have no crevices where debris can accumulate. Their stainless steel connectors, plastic lens, and mounts resist acids, alkalis, and other chemicals commonly used in food environment washdowns.

Know your machine’s status at a glance—green for running, red for stopped, yellow for standby. Using your programmable logic controller (PLC), you can adjust the brightness of these lights and mix red, green, and blue light to achieve thousands of colors.

Illuminate machines or monitor processes in environments that reach up to 210° F. These lights have a thick housing that acts as a heat sink to protect the LEDs and driver from overheating.

Mount these lights into a recessed opening on your machine—they sit flush against the surface for a streamlined appearance.

These thin, flexible lights wrap around equipment, hide under cabinets, and squeeze into tight spaces—all you need is an outlet. Just peel and stick to attach them to any smooth surface.

Bend these flexible lights around corners or squeeze them into spaces where bulky fixtures won’t fit. They’re brighter than plug-in tape lights, so you can use them for inspections and other detailed work.

Light up drawers and enclosures where power isn’t available—these lights are compact and powered by battery.

Safe to use in areas with ignitable concentrations of flammable or combustible gases, vapors, liquids, and dust, these lights are rated NEC Class I, II, and III.

With built-in LEDs, these lights deliver all the brightness of larger dock lights in a low-profile design. A hinge stop keeps the arm from extending past the dock door, and the curved design fits around the track.