Mount this light on a pole to illuminate pedestrian areas such as streets and walkways.

Heads adjust to any angle so you can direct light where needed.

Illuminate outdoor areas and objects such as parking lots, flag poles, and billboards.

No need for wiring—these lights plug-in with a three-prong plug.

These lights automatically turn on when movement is detected and off when an area is unoccupied.

These lights produce a wide beam of uniform light to fill large, open areas with ceilings up to 18-ft. high.

Suspend or mount with fasteners to the ceiling.

Also known as jelly jar lights. These fixtures have a guard that protects the lens from breaking.

A wraparound lens disperses light from the sides as well as the bottom to produce ambient lighting.

Also known as pigtail holders. Temporarily wire these sockets to provide light during construction.

Mount these fixtures where you need light but don't have an electrical connection. They automatically turn on when movement is detected and off when an area is unoccupied.

Rated IP65, these lights are sealed to protect against light washdowns from a garden hose. They have a height-adjustable stand and light heads that pivot up and down to direct light where it's needed.

The handle on this floodlight also acts as a stand—pivot it 360° to aim light where it's needed. This floodlight is small and easy to carry to job sites that don't have electrical power.

A series of bulb heads are attached to a power cord to provide overhead lighting for job sites.

Use these with portable lights that use screw-in bulbs.

With a NEMA 4X rating, these lights resist degradation when exposed to corrosive liquids, withstand liquids sprayed during washdowns, and are dust tight.

Safe for use in environments where hazardous material is present.

Rated IP07, these headlamps withstand temporary submersion in a maximum of one meter of water for up to 30 minutes.

In addition to pivoting 210°, the light heads rotate 360° for directing light exactly where it’s needed. They're rated for use in environments where hazardous material is present.

Attach to your key ring or hat so you’ll always have a flashlight on hand. They're rated for use in environments where hazardous material is present.

Always have a flashlight on hand—these attach to a key ring.

Made of stainless steel, these pocket-size flashlights have a smooth, easy-to-clean surface.

Small enough to fit in your pocket.

These classic-style machine lights have a reflector to distribute light more evenly than strip machine lights.

Just like traditional tubular lights that illuminate your machine with a bright white light, these lights can also be programmed to switch over to a red or green light for communicating machine status.

With a slimmer profile than other strip machine lights, these lights fit in tight spots on workspaces and inside machinery because they don’t have a circuit board.

Mount add-on heads in remote areas to extend emergency lighting.

These lights are UL rated for use in hazardous locations where flammable/combustible gases, vapors, and liquids may be present.

Shine light on machinery and through the sight glass on tanks to inspect food, brewery, chemical, pharmaceutical, and bio-tech processing lines.

The articulating arm on these lights holds its position better than gooseneck-arm lights, especially around vibration.

A sealed head and switch keeps these lights shining in wet environments. They swing out from the wall and adjust horizontally and vertically to illuminate loading dock and trailers.

Use these bulbs in standard sockets, panels, and appliances.

Choose from blue, green, red, and yellow bulbs.

Small but powerful, these bulbs are commonly used in stage and security lighting.

Pins on the base lock these bulbs into sockets to withstand vibration. They're often used in machines and elevators.

Prongs on the side of the base plug into specialty track lighting fixtures.

Turn standard light bulb sockets into standalone floodlight fixtures using these bulbs, which have an aluminum reflector to focus light downward and add a finished look.

Pins on the base lock these bulbs into sockets to withstand vibration.

Illuminate warehouses, factories, and arenas with the bright, white light of these metal halide light bulbs.

Replace metal halide, high-pressure sodium, and mercury vapor light bulbs with longer-lasting, energy-efficient LEDs.

Pins on either side of the base lock these bulbs into sockets.

These bulbs are sized to fit tight spaces such as indicators and vehicle lights.

Fit these bulbs in tight spaces such as signs, control panels, indicators, and flashlights.

Wire terminals allow you to connect these bulbs to a power source through a panel.

Bulbs have two filaments, which operate at different brightness levels.

These bulbs are sized to fit tight spaces such as signs, control panels, indicators, and flashlights.

Replace bayonet base incandescent bulbs in exit signs with longer-lasting, energy-efficient LEDs.

Use these as replacement bulbs in stack lights.

Often used in task lights, these four-pin wedge base bulbs are comparable to PL, Dulux, and Biax bulbs.

These changers create a vacuum seal against a light bulb. They're often used to change bulbs in recessed lights where there's no room to reach around the bulb.

Push these changers over light bulbs. Rubber sleeves cover the springs to grip the bulb when twisting.

The open design of these guards allows heat to dissipate from screw-in light bulbs.