Overhead Fans | McMaster-Carr

	REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration, Evaluation, Authorization and Restriction of Chemicals)

REACH Compliant

Forward

How can we improve?

72 Products

About Choosing a Heater

About Exhaust Fans

About Sound Levels

Measured in decibels (dB), volume ratings indicate how much noise equipment makes. Some common volume levels include a whisper @ 20 dB, a refrigerator @ 40 dB, a conversation @ 60 dB, and a light machine shop @ 90 dB. OSHA recommends hearing protection for exposure to 80 dB and greater.

Direct Long-Range Ceiling-Mount Gas Heaters

One Burner

Two Burners

Our most powerful ceiling-mount direct heaters, these warm people in large spaces, such as warehouses. All have a safety shut-off that cuts the gas supply if the flame goes out. They include a wall-mount thermostat.

Heaters with two burners allow for greater control over how much heat is generated—use one or both burners depending on your needs.

Heaters with a pilot light ignition do not require electricity. Heaters with an electronic spark ignition are good for drafty areas where a pilot light could be extinguished.

Natural Gas Heaters with Pilot Light Ignition

Heaters
				Inlet				O'all								Repl. Thermocouples
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	No. of Burners	Max. Fuel Consumption, cfh	Pipe Size	Thread Type	Gender	Max. Mount. Ht., ft.	Ht.	Wd.	Dp.	Housing Material	For Use Outdoors	Temp. Setting, °F		Each		Each
40,000	1,170 sq. ft. @ 10° F 390 sq. ft. @ 20° F 290 sq. ft. @ 30° F 290 sq. ft. @ 40° F	1	40	3/4	NPT	Female	12	12"	31"	20"	Steel	No	50° to 90°	00000000	0000000	000000000	000000
60,000	2,050 sq. ft. @ 10° F 680 sq. ft. @ 20° F 510 sq. ft. @ 30° F 510 sq. ft. @ 40° F	1	60	3/4	NPT	Female	15	12"	46"	20"	Steel	No	50° to 90°	00000000	000000	000000000	00000
100,000	2,930 sq. ft. @ 10° F 980 sq. ft. @ 20° F 730 sq. ft. @ 30° F 730 sq. ft. @ 40° F	2	100	3/4	NPT	Female	28	11"	61"	22"	Steel	No	50° to 90°	00000000	000000	000000000	00000
120,000	4,100 sq. ft. @ 10° F 1,370 sq. ft. @ 20° F 1,020 sq. ft. @ 30° F 1,020 sq. ft. @ 40° F	2	120	3/4	NPT	Female	36	11"	83"	22"	Steel	No	50° to 90°	00000000	00000000	000000000	00000

Natural Gas Heaters with Electronic Spark Ignition—120V AC, Single Phase, Wire Leads

Heaters
				Inlet				O'all								Repl. Pilot Burners
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	No. of Burners	Max. Fuel Consumption, cfh	Pipe Size	Thread Type	Gender	Max. Mount. Ht., ft.	Ht.	Wd.	Dp.	Housing Material	For Use Outdoors	Temp. Setting, °F		Each		Each
40,000	1,170 sq. ft. @ 10° F 390 sq. ft. @ 20° F 290 sq. ft. @ 30° F 290 sq. ft. @ 40° F	1	40	3/4	NPT	Female	12	12"	31"	20"	Steel	No	50° to 90°	00000000	0000000	00000000	000000
70,000	2,050 sq. ft. @ 10° F 680 sq. ft. @ 20° F 510 sq. ft. @ 30° F 510 sq. ft. @ 40° F	1	60	3/4	NPT	Female	15	12"	46"	20"	Steel	No	50° to 90°	00000000	000000	00000000	00000
100,000	2,930 sq. ft. @ 10° F 980 sq. ft. @ 20° F 730 sq. ft. @ 30° F 730 sq. ft. @ 40° F	2	100	3/4	NPT	Female	28	11"	61"	22"	Steel	No	50° to 90°	00000000	000000	00000000	00000
120,000	4,100 sq. ft. @ 10° F 1,370 sq. ft. @ 20° F 1,020 sq. ft. @ 30° F 1,020 sq. ft. @ 40° F	2	120	3/4	NPT	Female	36	11"	83"	22"	Steel	No	50° to 90°	00000000	00000000	00000000	00000

Propane Heaters with Pilot Light Ignition

Heaters
				Inlet				O'all								Repl. Thermocouples
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	No. of Burners	Max. Fuel Consumption, lbs./hr.	Pipe Size	Thread Type	Gender	Max. Mount. Ht., ft.	Ht.	Wd.	Dp.	Housing Material	For Use Outdoors	Temp. Setting, °F		Each		Each
40,000	1,170 sq. ft. @ 10° F 390 sq. ft. @ 20° F 290 sq. ft. @ 30° F 290 sq. ft. @ 40° F	1	2	3/4	NPT	Female	12	12"	31"	20"	Steel	No	50° to 90°	00000000	0000000	000000000	000000
100,000	2,930 sq. ft. @ 10° F 980 sq. ft. @ 20° F 730 sq. ft. @ 30° F 730 sq. ft. @ 40° F	2	5	3/4	NPT	Female	28	11"	61"	22"	Steel	No	50° to 90°	00000000	000000	000000000	00000

Propane Heaters with Electronic Spark Ignition—120V AC, Single Phase, Wire Leads

Heaters
				Inlet				O'all								Repl. Pilot Burners
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	No. of Burners	Max. Fuel Consumption, lbs./hr.	Pipe Size	Thread Type	Gender	Max. Mount. Ht., ft.	Ht.	Wd.	Dp.	Housing Material	For Use Outdoors	Temp. Setting, °F		Each		Each
40,000	1,170 sq. ft. @ 10° F 390 sq. ft. @ 20° F 290 sq. ft. @ 30° F 290 sq. ft. @ 40° F	1	2	3/4	NPT	Female	12	12"	31"	20"	Steel	No	50° to 90°	00000000	0000000	00000000	000000
100,000	2,930 sq. ft. @ 10° F 980 sq. ft. @ 20° F 730 sq. ft. @ 30° F 730 sq. ft. @ 40° F	2	5	3/4	NPT	Female	28	11"	61"	22"	Steel	No	50° to 90°	00000000	000000	00000000	00000

Direct Long-Range Ceiling-Mount Electric Heaters

Warm people in large, drafty spaces, such as shops and garages.

Thermostat is sold separately. A relay (not included) is required between the heater and thermostat. 1818K26 and 1818K27 heaters do not require a relay.

Heaters
					Overall							Wall-Mount Thermostats
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	Wattage, W	Current, A	Max. Mounting Ht., ft.	Ht.	Wd.	Dp.	Housing Material	For Use Outdoors		Each		Each
240V AC, Single Phase—Wire Leads
10,700	140 sq. ft. @ 10° F 70 sq. ft. @ 20° F 50 sq. ft. @ 30° F 40 sq. ft. @ 40° F	3,150	13.1	14	9"	48"	20"	Aluminum	No	0000000	0000000	0000000	0000000
240V AC, Three Phase—Wire Leads
14,600	430 sq. ft. @ 10° F 210 sq. ft. @ 20° F 140 sq. ft. @ 30° F 110 sq. ft. @ 40° F	4,300	10.4	16	9"	32"	20"	Aluminum	No	0000000	000000	0000000	000000
32,400	950 sq. ft. @ 10° F 470 sq. ft. @ 20° F 320 sq. ft. @ 30° F 240 sq. ft. @ 40° F	9,500	22.9	20	9"	53"	20"	Aluminum	No	0000000	00000000	0000000	000000
480V AC, Single Phase—Wire Leads
10,700	140 sq. ft. @ 10° F 70 sq. ft. @ 20° F 50 sq. ft. @ 30° F 40 sq. ft. @ 40° F	3,150	6.6	14	9"	48"	20"	Aluminum	No	0000000	000000	0000000	000000
480V AC, Three Phase—Wire Leads
14,600	430 sq. ft. @ 10° F 210 sq. ft. @ 20° F 140 sq. ft. @ 30° F 110 sq. ft. @ 40° F	4,300	5.2	16	9"	32"	20"	Aluminum	No	0000000	000000	0000000	000000
32,400	950 sq. ft. @ 10° F 470 sq. ft. @ 20° F 320 sq. ft. @ 30° F 240 sq. ft. @ 40° F	9,500	11.4	20	9"	53"	20"	Aluminum	No	0000000	00000000	0000000	000000

Direct Short-Range Ceiling- and Wall-Mount Electric Heaters

Ceiling Mount

Ceiling/Wall Mount

NEMA 5-15 Plug

NEMA 6-15 Plug

Install near loading docks and other drafty areas to warm people and objects.

Ceiling-mount heaters hang indoors and in sheltered outdoor areas. Thermostat is sold separately.

Ceiling/wall-mount heaters have a stainless steel grille and heating element to resist corrosion in pump houses and other moist locations. All have a built-in thermostat.

Heaters
						Overall			Material					Replacement Heating Elements		Wall-Mount Thermostats
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	Wattage, W	Current, A	Cord Lg., ft.	Max. Mounting Ht., ft.	Ht.	Wd.	Dp.	Housing	Heating Element	For Use Outdoors		Each		Each		Each
Ceiling Mount
120V AC, Single Phase—Three-Prong Plug (NEMA 5-15)
5,100	150 sq. ft. @ 10° F 70 sq. ft. @ 20° F 50 sq. ft. @ 30° F 40 sq. ft. @ 40° F	1,500	12.5	6	9	7"	48"	6"	Galvanized Steel	Quartz	Yes	0000000	0000000	0000000	000000	0000000	0000000
240V AC, Single Phase—Three-Prong Plug (NEMA 6-15)
10,200	300 sq. ft. @ 10° F 150 sq. ft. @ 20° F 100 sq. ft. @ 30° F 70 sq. ft. @ 40° F	3,000	12.5	6	10	7"	59"	6"	Galvanized Steel	Quartz	Yes	0000000	000000	0000000	000000	0000000	000000

				Overall			Material
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	Wattage, W	Current, A	Ht.	Wd.	Dp.	Housing	Heating Element	For Use Outdoors	Temperature Setting, °F		Each
Ceiling/Wall Mount
120V AC, Single Phase—Wire Leads
1,700	50 sq. ft. @ 10° F 20 sq. ft. @ 20° F 20 sq. ft. @ 30° F 10 sq. ft. @ 40° F	500	4.2	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	0000000
2,500	70 sq. ft. @ 10° F 40 sq. ft. @ 20° F 20 sq. ft. @ 30° F 20 sq. ft. @ 40° F	750	6.3	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	000000
3,400	100 sq. ft. @ 10° F 50 sq. ft. @ 20° F 30 sq. ft. @ 30° F 20 sq. ft. @ 40° F	1,000	8.3	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	000000
240V AC, Single Phase—Wire Leads
1,700	50 sq. ft. @ 10° F 20 sq. ft. @ 20° F 20 sq. ft. @ 30° F 10 sq. ft. @ 40° F	500	2	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	000000
2,500	70 sq. ft. @ 10° F 40 sq. ft. @ 20° F 20 sq. ft. @ 30° F 20 sq. ft. @ 40° F	750	3.1	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	000000
3,400	100 sq. ft. @ 10° F 50 sq. ft. @ 20° F 30 sq. ft. @ 30° F 20 sq. ft. @ 40° F	1,000	4.2	17"	7"	4"	Steel	Stainless Steel	No	40° to 90°	0000000	000000

Ceiling Tile Electric Heaters

Eliminate cold spots without taking up space. Slip these heaters into your drop-ceiling grid above windows and doorways to complement your existing heating system.

Thermostat is sold separately.

Heaters
					Overall			Housing				Thermostats
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	Wattage, W	Current, A	Max. Mounting Ht., ft.	Ht.	Wd.	Dp.	Material	Color		Each		Each
120V AC/240V AC, Single Phase—Wire Leads
1,200	40 sq. ft. @ 10° F 20 sq. ft. @ 20° F 10 sq. ft. @ 30° F 10 sq. ft. @ 40° F	370	3.1	8	24"	24"	1"	Painted Steel	White	0000000	0000000	00000000	000000
2,500	70 sq. ft. @ 10° F 40 sq. ft. @ 20° F 20 sq. ft. @ 30° F 20 sq. ft. @ 40° F	750	6.3	8	48"	24"	1"	Painted Steel	White	0000000	000000	00000000	00000
277V AC, Single Phase—Wire Leads
1,200	40 sq. ft. @ 10° F 20 sq. ft. @ 20° F 10 sq. ft. @ 30° F 10 sq. ft. @ 40° F	370	1	8	24"	24"	1"	Painted Steel	White	0000000	000000	00000000	00000
2,500	70 sq. ft. @ 10° F 40 sq. ft. @ 20° F 20 sq. ft. @ 30° F 20 sq. ft. @ 40° F	750	3	8	48"	24"	1"	Painted Steel	White	0000000	000000	00000000	00000

Portable Small-Space Electric Heaters

5,100 Btu/hr. Heater with Plastic Housing

5,100 Btu/hr. Heater with Steel Housing

19,100 Btu/hr. Heater with Steel Housing

NEMA 1-15 Plug

NEMA 5-15 Plug

NEMA 6-30 Plug

Carry these heaters to offices, workstations, and other small spaces. All have a built-in thermostat.

Plastic heater shuts off if tipped over or airflow is obstructed.

19,100 Btu/hr. heater has a bracket you can use as a stand or to mount to the wall or ceiling. When operating at 208 volts AC, maximum area heated and heat output are reduced by 25%.

						Overall
Heat Output, Btu/hr.	Max. Area Heated @ Temperature Change	Airflow, cfm	Wattage, W	Current, A	Cord Lg., ft.	Ht.	Wd.	Dp.	Housing Material	Temperature Setting, °F		Each
120V AC, Single Phase—Two-Prong Plug (NEMA 1-15)
5,100	__	25	1,500	12.5	6	8"	5"	8"	Plastic	65° to 85°	0000000	000000
120V AC, Single Phase—Three-Prong Plug (NEMA 5-15)
5,100	750 cu. ft. @ 10° F 370 cu. ft. @ 20° F 250 cu. ft. @ 30° F 190 cu. ft. @ 40° F	120	1,500	12.5	6	11"	9"	13"	Steel	0° to 80°	0000000	000000
208V AC/240V AC, Single Phase—Three-Prong Plug (NEMA 6-30)
19,100	2,540 cu. ft. @ 10° F 1,270 cu. ft. @ 20° F 840 cu. ft. @ 30° F 630 cu. ft. @ 40° F	260	5,600	23.4	6	18"	14"	12"	Steel	35° to 85°	0000000	000000

Ceiling-Mount Lavatory Exhaust Fans

Use these fans to draw stagnant and humid air out of a room.

Fans that cannot be sold to the regions listed do not meet local energy efficiency requirements.

For technical drawings and 3-D models, click on a part number.

For Round Duct

				Guard		For Opening
	For Duct Dia.	Airflow, cfm	Volume, dBA	Lg.	Wd.	Wd.	Dia.	Dp.	Housing Material	Mount. Fasteners Included	Mount. Hole Dia.	Mount. Location	Features	Specifications Met	Cannot Be Sold To		Each
120V AC, Single Phase—Hardwire
1	3"	50	48	9 1/4"	9"	7 1/4"	__	3 5/8"	Steel	No	1/8"	Ceiling, Wall	Backdraft-Preventing Damper	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	000000
1	3"	70	54	9 1/4"	9"	7 1/4"	__	3 5/8"	Steel	No	1/8"	Ceiling, Wall	Backdraft-Preventing Damper	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	00000
1	4"	80	31	12"	11 1/2"	9 1/4"	__	5 3/4"	Steel	No	3/16"	Ceiling, Wall	Backdraft-Preventing Damper	UL Listed	__	0000000	00000
2	8"	180	59	11 1/2"	11 1/2"	__	8 1/4"	7"	Steel	No	3/16"	Ceiling	Backdraft-Preventing Damper	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	000000
120V AC, Single Phase—Plug
1	4"	110	28	12"	11 1/2"	9 1/4"	__	5 3/4"	Steel	Yes	1/4"	Ceiling, Wall	Backdraft-Preventing Damper	UL Listed	__	000000	000000

For Rectangular Duct

	For Duct				Guard		For Opening
	Ht.	Wd.	Airflow, cfm	Volume, dBA	Lg.	Wd.	Wd.	Dp.	Housing Material	Mount. Fasteners Included	Mount. Hole Dia.	Mount. Location	Features	Specifications Met	Cannot Be Sold To		Each
120V AC, Single Phase—Hardwire
3	3 1/4"	10"	160	51	11 1/2"	11 1/2"	12"	3 1/4"	Steel	No	3/16"	Ceiling, Wall	Backdraft-Preventing Damper	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	0000000

Ceiling-Mount Lavatory Exhaust Fans with Lights

These fans have a light that can operate alone or share a switch with the fan. Use them to draw stagnant and humid air out of a room.

Fans that cannot be sold to the regions listed do not meet local energy efficiency requirements.

For technical drawings and 3-D models, click on a part number.

			Guard		For Opening			Bulb
For Duct Dia.	Airflow, cfm	Volume, dBA	Lg.	Wd.	Wd.	Dp.	Housing Material	Included	No. Required	Max. Wattage, W	Mount. Fasteners Included	Mount. Hole Dia.	Features	Specifications Met	Cannot Be Sold To		Each
For Round Duct
120V AC, Single Phase—Hardwire
4"	50	41	11 1/8"	10 5/8"	8"	5 3/4"	Steel	No	1	100	No	3/16"	Backdraft-Preventing Damper, Light	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	000000
4"	70	38	12 1/8"	11 1/2"	9 1/4"	5 3/4"	Steel	No	1	100	No	3/16"	Backdraft-Preventing Damper, Light	UL Listed	CO, DC, MA, NJ, OR, VT, WA	0000000	000000
120V AC, Single Phase—Plug
4"	110	28	12 1/2"	11 3/4"	9 1/4"	5 3/4"	Steel	Built-In LED	__	__	Yes	1/4"	Backdraft-Preventing Damper, Light	UL Listed	__	0000000	000000

Ultra-Quiet Ceiling-Mount Lavatory Exhaust Fans

Keep noise to a minimum with 1/2" thick acoustical insulation and vibration-resistant motor mounts. Use these fans to draw stagnant and humid air out of a room.

Speed controls are optional. Speed controls for fans that fit 19" wide and 8" diameter ducts fit single gang electrical boxes. Speed controls for fans that fit 12" wide ducts mount internally on the fan.

For technical drawings and 3-D models, click on a part number.

For Round Duct

For Round Duct

			Guard
For Duct Dia.	Airflow, cfm	Volume, dBA	Lg.	Wd.	Housing Material	Mount. Fasteners Included	Mount. Hole Dia.	Mount. Location	Features	Specifications Met		Each
120V AC, Single Phase—Hardwire
8"	230	36	14"	14"	Steel	No	1/2"	Ceiling, Wall	Backdraft-Preventing Damper, Vibration-Resistant Mounts	UL Listed	0000000	0000000

For Rectangular Duct

For Duct				Guard
Ht.	Wd.	Airflow, cfm	Volume, dBA	Lg.	Wd.	Housing Material	Mount. Fasteners Included	Mount. Hole Dia.	Mount. Location	Features	Specifications Met		Each
120V AC, Single Phase—Hardwire
5"	19"	480	40	23 1/4"	14"	Steel	No	1/2"	Ceiling, Wall	Backdraft-Preventing Damper, Vibration-Resistant Mounts	UL Listed	0000000	0000000
8"	12"	910	48	23 7/8"	19 7/8"	Steel	No	1/2"	Ceiling, Wall	Backdraft-Preventing Damper, Vibration-Resistant Mounts	UL Listed	0000000	000000

Speed Controls

For 19" Wide and 8" Diameter Ducts

For 12" Wide Ducts

For 19" Wide and 8" Diameter Ducts
For Duct Shape	Electrical Connection	Mounting Fasteners Included		Each
Rectangular, Round	Hardwire	Yes	0000000	000000
For 12" Wide Ducts
Rectangular	Hardwire	Yes	0000000	00000

Economy Ceiling-Mount Fans

Shown With Extension Pipe (Not Included)

All of these fans have a direct-drive motor, which has fewer moving parts than belt-drive motors for less maintenance. They also have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments. Threaded extension pipe for mounting is not included. These fans cannot be sold to California due to local energy efficiency requirements.

										Mounting
Blade Dia.	Airflow, cfm	Volume	Motor Speed, rpm	No. of Speeds	Power, hp	Current, A	Cord Lg., ft.	Blade Material	Guard Material	Fasteners Included	Hole Dia.	Required Pipe Size	Specifications Met	Cannot Be Sold To		Each
120V AC, Single Phase—Three Prong Plug
Non-Oscillating
18"	3,100	57 dBA @ 15 ft.	1,500	3	1/6	1.5	9	Steel	Powder-Coated Steel	No	3/8"	1 1/2	ETL Listed	CA	0000000	0000000
20"	3,600	52 dBA @ 15 ft.	1,500	3	1/6	1.6	9	Steel	Powder-Coated Steel	No	3/8"	1 1/2	ETL Listed	CA	0000000	000000
30"	7,400	65 dBA @ 15 ft.	1,025	3	1/4	2.4	10	Steel	Powder-Coated Steel	No	3/8"	1 1/2	ETL Listed	CA	0000000	000000

Replacement Motor for 1,500-rpm Fans	0000000	Each	000000
Replacement Motor for 1,025-rpm Fans	0000000	Each	000000

High-Output Ceiling-Mount Fans

Shown With Extension Pipe (Not Included)

Generate at least 25% greater airflow than economy and premium fans. All of these fans have a long-lasting direct-drive motor with ball bearings, which has fewer moving parts than belt-drive motors for less maintenance. They also have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments. Threaded extension pipe for mounting is not included. These fans cannot be sold to California due to local energy efficiency requirements.

120V AC, Single Phase—Three Prong Plug
Blade Dia.	Airflow, cfm	Volume	Motor Speed, rpm	No. of Speeds	Power, hp	Current, A	Cord Lg., ft.	Blade Material	Guard Material	Mounting Fasteners Included	Mounting Hole Dia.	Required Pipe Size	Cannot Be Sold To		Each
Non-Oscillating
24"	7,400	77 dB @ 5 ft.	1,100	2	1/2	5.0	15	Aluminum	Chrome-Plated Steel	No	3/8"	1	CA	0000000	0000000
30"	9,700	79 dB @ 5 ft.	1,100	2	1/2	5.0	15	Aluminum	Chrome-Plated Steel	No	3/8"	1	CA	0000000	000000

Premium Ceiling-Mount Fans

Shown With Extension Pipe (Not Included)

With a ball-bearing motor and cupped fan blades, these fans last longer and focus airflow better than economy fans. All have a direct-drive motor, which has fewer moving parts than belt-drive motors for less maintenance. They also have a totally enclosed motor enclosure, which can be used in dirty, dusty, and damp environments. Threaded extension pipe for mounting is not included. These fans cannot be sold to California due to local energy efficiency requirements.

120V AC, Single Phase—Three Prong Plug
Blade Dia.	Airflow, cfm	Volume	Motor Speed, rpm	No. of Speeds	Power, hp	Current, A	Cord Lg., ft.	Blade Material	Guard Material	Mounting Fasteners Included	Mounting Hole Dia.	Required Pipe Size	Specifications Met	Cannot Be Sold To		Each
Non-Oscillating
24"	5,500	61 dB @ 5 ft.	1,050	3	1/3	2.5	15	Aluminum	Chrome-Plated Steel	No	3/8"	1	UL Listed	CA	0000000	0000000
30"	8,400	65 dB @ 5 ft.	1,025	3	1/3	2.7	15	Aluminum	Chrome-Plated Steel	No	3/8"	1	UL Listed	CA	0000000	000000

Replacement Cord	0000000	Each	000000
Replacement End Dome Assembly	0000000	Each	00000

Ceiling Fans

Mount these fans on flat ceilings. They include a support cable and downrods to mount them into joists. All have optional speed control.

Optional installation kits (sold separately) allow fans to mount between joists.

For technical drawings and 3-D models, click on a part number.

				Blade
Blade Dia.	Airflow, cfm	No. of Speeds	Current, A	Rotation	Material	Color	For Min. Ceiling Ht., ft.	Mounting Fasteners Included	Specifications Met		Each
120V AC, Single Phase—Hardwire
Non-Oscillating
36"	2,126	1	0.3	Nonreversible	Painted Steel	White	10	Yes	C-UL Listed, UL Listed	0000000	0000000
48"	3,861	1	0.4	Nonreversible	Painted Steel	White	10	Yes	C-UL Listed, UL Listed	0000000	000000
56"	8,959	1	0.9	Nonreversible	Painted Steel	White	10	Yes	C-UL Listed, UL Listed	0000000	000000
60"	6,090	1	0.6	Nonreversible	Painted Steel	White	10	Yes	C-UL Listed, UL Listed	0000000	000000

Optional Installation Kit

Includes		Each
Adjustable Brace, Electrical Box, Mounting Hardware	0000000	000000

Multi-Mount Office Fans

You can mount these fans on beams and walls. The fan head tilts to direct air where it's needed.

Fans
				Overall											Replacement Motors
Blade Dia.	Airflow, cfm	No. of Speeds	Current, A	Ht.	Wd.	Dp.	Cord Lg., ft.	Blade Material	Guard Material	Mounting Fasteners Included	Mounting Hole Dia.	Specifications Met		Each		Each
120V AC, Single Phase—Three Prong Plug
Non-Oscillating, Tilting
12"	1,300	3	0.8	15"	15"	12"	9	Steel	Steel	No	3/4"	ETL Listed	0000000	000000	000000	00
18"	3,100	3	1.5	21"	22"	16"	9	Steel	Steel	No	3/4"	ETL Listed	0000000	000000	0000000	000000