Sets include a plug and socket with wire leads already installed, so they can be quickly added to existing wiring systems. They fit standard Molex plugs and sockets.

Configure a connector for your application—combine housings with pins and sleeves for different wire sizes. They fit AMP MATE-N-LOK connectors.

Stack as many connectors on top of each other as needed—the housings clamp together to form a secure attachment.

Configure a connector for your application—combine inserts for power and signal with a base and a hood.

Build a connector that fits in tight spaces by combining male and female inserts for power and signal with a compact base and a hood.

A rubber seal and stainless steel hardware give these connectors excellent chemical resistance. They're rated NEMA 12, 4X, and IP65 for protection against corrosion, oil, and washdown environments.

Carry up to four times the current of standard Compact Latching Connectors. The base and hood latch together securely, yet can be quickly detached for equipment repair or replacement.

Rated to MIL-DTL-5015 specifications, these connectors are compatible with other products that meet the same standard. They screw together for a secure connection.

These connectors have the same pin and socket configuration as connectors that meet MIL-DTL-26482, so they can be used with products that meet the same standard. Quickly mate them by pushing them together.

These general purpose M23 connectors send power or signal to servomotors, servocontrollers, and servodrives.

Use these sockets with Allen-Bradley servomotor systems.

Each set includes one plug and one socket. These connectors withstand moisture, harsh engine fluids, and high temperatures. Also known as weather-pack connectors.

Use these connectors in vehicles and other agricultural and construction equipment. They have a sealed nylon housing that resists dust and temporary submersion.

Often used to send power and signal to automated systems, motors, and pumps, these mini connectors carry higher currents than M5, M8, and M12 connectors.

Protect harsh environment mini connectors when not in use.

Also known as dummy plugs, these plugs close the electrical circuit on your mini connector, so you can safely change devices or repair connections.

Protect against signal interference while sending 2-3 times more current than M12 connectors.

Rated IP69K, these M16 connectors protect against dust, debris, and hot, high-pressure jets of water at high volumes.

Because they tightly thread to M12 connections, these connectors won’t let contaminants in or come loose from vibration in rugged industrial environments and automated systems as they send power and signal or just power to your equipment.

Send power and signal to devices with M12 connections that are exposed to some of the toughest industrial stresses—from welding to metal machining and changing temperatures.

Visually confirm your connector is working properly. A green light means your connector has power, while yellow means it has signal.

Plug these connectors into hazardous location devices. Using a NAMUR signal, they operate at a low current and voltage, so they prevent the risk of sparks and ignition in volatile areas.

Push these connectors together to quickly create signal and data connections in tight spaces. They need less space to mate than screw-together connectors, which require two hands to twist them in place.

A TPE cable protects these connectors from oil, weld slag, and other tough industrial stresses as they send signal and power to low-current devices with M8 connections.

Minimize signal loss between low-current devices with M8 connections.

Visually check that your low-current devices with M8 connections are powered up and sending and receiving signals. These connectors illuminate green if they have power and yellow if they have signal.

These connectors meet international standards IEC 309-1 and 309-2. They prevent an electrical arc when separating mated connectors, so you can safely connect and disconnect with the power on.

Caps are watertight to protect safe-break plugs when not in use.

Caps are watertight to protect hazardous location safe-break plugs when not in use.

When used together, connectors maintain a watertight and corrosion-resistant NEMA 4X connection.

Make secure connections with machine tools, robots, and other equipment that vibrates frequently and carries currents as high as 300 amps.

Mount these receptacles to control cabinets and equipment in order to quickly connect and disconnect M29 power cords.

Often used in devices that branch off of the main power line, these connectors power high-amperage fans, pumps, and machines in motor controls, conveyors, and sorting and packaging systems.

Power robotic arms and other high-amperage machines in motor controls, conveyors, and sorting and packaging systems from your main M35 power line.

Reduce the likelihood of slips and falls in high-traffic areas—connectors won't roll when stepped on.

With thick threads similar to a light bulb, these connectors take only a few turns to lock into place for a secure connection in washdown and high-vibration areas. Detach them just as quickly for frequent maintenance.

These connectors are designed for use in audio equipment.

Connect audio equipment. These connectors mount to panels of any thickness, as long as you drill a mounting hole first.

Unlike traditional RJ45 connectors found in data centers, these connectors stand up to rugged industrial environments since they tightly thread to devices with M12 connections, sealing out contaminants and resisting shaking loose from vibration. Use them to transfer high-speed data between sensors, switches, computers, IO modules, programmable logic controllers (PLCs), and other equipment.

Step on or roll carts and platform trucks over these M12 cords without crushing them.

TPE insulation protects these cords from some of the toughest industrial conditions, including abrasion, coolants, chemicals, UV rays, and weld slag. Use them in areas with welding, machining, and fluctuating temperatures to send signal and power to M12 proximity switches, valves, and other devices.

Also known as pico cords, these cords are often used with low-current 8 mm proximity and photoelectric switches.

Connect two devices to a distribution block or I/O module with just one cord. Often used with sensors and actuators, these splitters send power/signals to your devices through a single connection.

With a higher maximum current than nano M8 and micro M12 cords, these mini cords are often used with automated systems, motors, and pumps.

These cords have an M8 connector on one end and an M12 connector on the other.

Use these cords in vehicles and other agricultural and construction equipment.

A few turns is all it takes to join these cords, which have thick threads similar to a light bulb, for a secure connection in washdown and high-vibration areas. They detach just as fast for frequent maintenance.

Similar to branches extending from a tree, these cords disperse power from a main power line to run a chain of devices. Power high-amperage fans, pumps, and other machines in motor controls, conveyors, and sorting and packaging systems.

Often used in automation systems such as conveyors and sorters, these cords have plug and socket ends, so they quickly connect and disconnect for maintenance and do not need to be hardwired.

Play audio from one source on two different speakers.

Transmit video to a single monitor.

Connect these lifters to your robot arm to pick up and move items using suction. They're electric, so you don't need a compressed air source.