Jaw Style Jaw Style |
|---|
|
DFARS (Defense Acquisition Regulations Supplement) DFARS (Defense AcquisitionRegulations Supplement)  |
|---|
For Use On For Use On |
|---|
|
|
RoHS (Restriction of Hazardous Substances) RoHS (Restriction ofHazardous Substances) |
|---|
|
REACH (Registration, Evaluation, Authorization and Restriction of Chemicals) REACH (Registration,Evaluation, Authorization and Restriction of Chemicals) |
|---|
|
Handle Material Handle Material |
|---|
|
Opening Style Opening Style |
|---|
|
Jaw Material Jaw Material |
|---|
|
Tip Material Tip Material |
|---|
|
Safety Properties Safety Properties |
|---|
|
For Maximum Medium-Hard Steel Hardness For Maximum Medium-Hard Steel Hardness |
|---|
|
For Maximum Soft Steel Hardness For Maximum SoftSteel Hardness |
|---|
|
Pinch Clamp Pliers
Crimp pinch clamps closed on hose and tube. Also known as pinch clamp pincers.
Straight jaw pliers must be used perpendicular to the hose.
Straight and side jaw pliers are good for tight spaces because you can use them parallel or perpendicular to the hose.
Pliers with a center handle have an added handle that reduces the fully open grip span. They also have a higher closing force than the other pliers, so they require less strength to crimp pinch clamps closed. You can use them with double pinch clamps.
Wire End Cutters for Hard Wire
Cut hard steel wire, nails, and small rivets close to the surface with the wide, flat jaws on these cutters. They're also known as nippers.
Comfort-Grip Wire End Cutters for Hard Wire
Plastic-cushioned grips make these cutters easy to hold during repeated cuts. They have hardened, precisely aligned cutting edges with a rust-resistant coating for clean, even cuts. Also known as nippers, they have wide, flat jaws that cut close to the surface.
| For Max. Wire Dia. | Overall Lg. | Jaw Wd. | Jaw Material | Handle Material | Grip Material | Opening Style | Each | |
For Use On Hard Steel, Aluminum, Copper | ||||||||
|---|---|---|---|---|---|---|---|---|
| 0.091" | 6 1/2" | 1" | Steel | Steel | Plastic | Manual | 000000 | 000000 |
| 0.091" | 7 1/4" | 1 1/16" | Steel | Steel | Plastic | Manual | 000000 | 00000 |
| 0.091" | 8 1/4" | 1 1/16" | Steel | Steel | Plastic | Manual | 000000 | 00000 |
| 0.091" | 10" | 7/8" | Steel | Steel | Plastic | Manual | 000000 | 00000 |
High-Force Wire End Cutters for Hard Wire
A double hinge provides high cutting force with low gripping pressure. Also known as nippers, these cutters have wide, flat jaws that cut close to the surface. A spring opens the jaws for quick cutting.
| For Max. Wire Dia. | Overall Lg. | Jaw Wd. | Jaw Material | Opening Style | Each | |
For Use On Hard Steel | ||||||
|---|---|---|---|---|---|---|
| 0.078" | 6 1/2" | 1" | Steel | Spring Assisted | 0000000 | 000000 |
Electrical-Insulating Wire End Cutters for Hard Wire
Insulated handles protect against shock from accidental contact with live electrical circuits. These cutters are tested to 1,000 volts to meet IEC 60900 and ASTM F1505. Also known as nippers, they have wide, flat jaws that cut close to the surface. Use with hard steel, aluminum, and copper wire.
| For Max. Wire Dia. | Overall Lg. | Jaw Wd. | Jaw Material | Handle Material | Grip Material | Opening Style | Each | |
For Use On Hard Steel, Aluminum, Copper | ||||||||
|---|---|---|---|---|---|---|---|---|
| 0.094" | 10" | 1" | Steel | Plastic | Plastic | Manual | 0000000 | 000000 |
Long-Life High-Force Wire End Cutters for Hard Wire
Sharpen or replace the jaws as they wear. These cutters have a double hinge that provides high cutting force with low gripping pressure. Also known as nippers, they have wide, flat jaws that cut close to the surface. A spring opens the jaws for quick cutting.
Nonsparking Wire End Cutters
Made of beryllium copper that is FM approved, these cutters satisfy OSHA requirements that specify nonsparking tools for locations where flammable vapors and combustible residues are present. Also known as nippers, they are nonmagnetic and have wide, flat jaws that cut close to the surface. Use with aluminum and copper wire.
Warning: Do not use these tools in direct contact with acetylene.
| For Max. Wire Dia. | Overall Lg. | Jaw Wd. | Jaw Material | Handle Material | Opening Style | Each | |
For Use On Aluminum, Copper | |||||||
|---|---|---|---|---|---|---|---|
| 3/8" | 7 1/4" | 1/2" | Beryllium Copper | Beryllium Copper | Manual | 0000000 | 0000000 |
Wire End Cutters
Also known as nippers, these cutters have wide, flat jaws that cut steel wire and bolts close to the surface. A spring opens the jaws for quick cutting.
For Max. Dia. | |||||||||
|---|---|---|---|---|---|---|---|---|---|
| Soft Steel | Medium-Hard Steel | Overall Lg. | Jaw Wd. | Jaw Material | Handle Material | Grip Material | Opening Style | Each | |
| 1/8" | 1/16" | 8" | 0.59" | Steel | Steel | Plastic | Spring Assisted | 0000000 | 000000 |
Precision Wire End Cutters
Precisely position and flush-cut copper, gold, silver, and magnetic wire. These tweezer-style cutters are also known as nippers.
Ceramic Tile Cutting Pliers
Also know as nippers, these pliers have carbide-tipped jaws to break off small pieces of tile for straight cuts. They have a spring handle for repetitive cutting.
| For Max. Thick. | Jaw Material | Overall Lg. | Handle Material | Grip Material | Jaw Wd. | Each | |
For Use On Ceramic Tile | |||||||
|---|---|---|---|---|---|---|---|
| 0.5" | Carbide | 8" | Steel | Plastic | 5/8" | 0000000 | 000000 |