McMaster-Carr logo
    Filter by
    System of Measurement
    Diameter
    Attribute Image
    DFARS Specialty Metals
    Punch Operation
    Graduations
    Export Control Classification Number (ECCN)
    Industrial Info Snippet
    Numeric Graduations
    Measuring Length
    Forward
    Enter e-mail addresses in the fields below
    Message
    Cancel
    Print
    How can we improve?
    Comments
    E-mail address (if you would like a response)
    10 Products

    Center Finders for Curved Surfaces

    Image of Product. Front orientation. Center Finders. Center Finders for Curved Surfaces.
    Center your work by mounting these into your drill chuck or collet and lining up the pointer with the mark on the shaft.
    For Max.
    Dia.
    Material
    Each
    5"Chrome-Plated Steel00000000000000

    Center-Locating Punches for Curved Surfaces

    Image of ProductInUse. Front orientation. Center Punches. Center-Locating Punches for Curved Surfaces.
    Locate and mark the centerline on rods, tubes, and pipes, lay out keyways, and establish angles for connections.
    Manual—Manual locators are for use with a hammer. Gently strike the rod to mark the center.
    Spring Loaded—Spring-loaded locators mark the center with the pull of a trigger.
    Adjustable Dial Protractor—Locators with an adjustable dial protractor aid in establishing marks for angled connections.
    Magnetic Base—Locators with a magnetic base keep the punch in place when striking.
    Punch
    Operation
    Angle Measured
    Range
    Graduations
    Angle Numeric
    Increments
    For Min.
    Pipe OD
    Material
    Punch
    Material
    Includes
    Features
    Each
    Manual———1"Aluminum
    		SteelMagnetic BaseBubble Levels0000000000000
    Manual0° to 90°2.5°10°1/2"Aluminum
    		SteelAdjustable Dial ProtractorBubble Level000000000000
    Spring Loaded0° to 90°2.5°10°1"Aluminum
    		SteelAdjustable Dial ProtractorBubble Level000000000000
     
    Replacement Levels
    Each
    Replacement Dial/Level Assembly0000000000000

    Starrett Swiveling Machine Tool Indicator Tip Sets

    Image of Product. Front orientation. Machine Tool Indicator Contact Points. Starrett Swiveling Machine Tool Indicator Tip Sets.
    Determine tool spindle position in relation to work surface, layout lines, holes, and slots. Also known as wiggler sets. Attachments are interchangeable.
    Includes
    Material
    Each
    0.10" Diameter Disc Contact, 0.25" Ball Contact, Chuck, Needle Point, Offset Indicator HolderSteel0000000000000

    Pipe Size Chart/Rulers

    Image of ProductInUse. Front orientation. Pipe Size Chart/Rulers.
    Measure outer diameter and mark lines around pipe. A pipe size conversion chart is printed on these chart/rulers. They’re fiber-reinforced rubber for grease, oil, gasoline, and salt water resistance.
    For Pipe OD
    Lg.
    Wd.
    Thk.
    Measuring
    Lg.
    Graduations (Numeric
    Graduations)
    Color
    Graduation
    Color
    Max. Temp.,
    ° F
    Each
    Rubber
    1" to 6", 2 mm to 60 cm30"2 5/8"3/64"28"1/16" (1"), 2 mm (1 cm)GrayWhite3600000000000000
    2" to 16", 2 mm to 78 cm60"3 7/8"3/64"36"1/16" (1"), 2 mm (1 cm)GrayWhite360000000000000
    6" to 30", 2 mm to 77 cm120"5 1/4"3/64"36"1/16" (1"), 2 mm (1 cm)GrayWhite360000000000000
     

    Vertical Center-Locating Punches for Curved Surfaces

    Image of ProductInUse. Front orientation. Center Punches. Vertical Center-Locating Punches for Curved Surfaces.
    Align the level to find and mark the vertical center of curved surfaces.
    Body
    For Dia.
    Point
    Dia.
    Lg.
    Wd.
    Ht.
    Punch
    Material
    Features
    Each
    5/8" to 8"9/32"1 7/8"1 1/2"1"SteelBubble Level0000000000000
     
    back to top