Probe Material Probe Material |
|---|
|
Maximum Diameter , Outer (Pipe) (For) Maximum Diameter ,Outer (Pipe) (For) |
|---|
|
|
Punch Operation Punch Operation |
|---|
|
For Maximum Flange Hole Diameter For Maximum FlangeHole Diameter |
|---|
|
|
Level Orientation Level Orientation |
|---|
|
Finish Finish |
|---|
|
Contour Transfers
Pipe Contour Transfers
Probes take the shape of a pipe joint so you can transfer the exact outline to the pipe before you cut.
Pipe Contour Transfer Markers
Lay out pipe and structural steel for any type or size of pipe fitting—elbows, tees, and wyes of all angles. These markers are lightweight aluminum.
| For Pipe OD | Angle Measuring Range | Graduation Marks (Numeric Increments) | Mount Type | Marker Type | Includes | Each | |
Anodized Aluminum | |||||||
|---|---|---|---|---|---|---|---|
| 1 1/2"-18" | 0°-90° | 2.5° (10°) | Magnet | Soapstone Crayon | Calibrated Protractor Dials, Holder for Soapstone Crayon, Level, Magnetic Base, Triple-Jointed Marking Arm | 000000 | 0000000 |
| 8"-48" | 0°-90° | 2.5° (10°) | Magnet | Soapstone Crayon | Built-in Bubble Level, Calibrated Protractor Dials, Holder for Soapstone Crayon, Magnetic Base, Triple-Jointed Marking Arm | 000000 | 000000 |
Center-Locating Punches for Curved Surfaces
Locate and mark the centerline on rods, tubes, and pipes, lay out keyways, and establish angles for connections.
Manual locator is for use with a hammer. Gently strike the rod to mark the center.
Spring-loaded locator marks the center with the pull of a trigger.
| Punch Operation | Angle Measuring Range | Graduation Marks | Numeric Increments | For Min. Pipe OD | Material | Punch Material | Includes | Features | Each | |
| Manual | 0°-90° | 2.5° | 10° | 1/2" | Aluminum | Steel | Adjustable Dial Protractor | Bubble Level | 000000 | 000000 |
| Spring Loaded | 0°-90° | 2.5° | 10° | 1" | Aluminum | Steel | Adjustable Dial Protractor | Bubble Level | 000000 | 000000 |
| Replacement Dial/Level Assembly | 0000000 | Each | 000000 |
Pipe Size Rulers
Measure outer diameter and mark lines around pipe. A pipe size conversion chart is printed on these rulers. They’re fiber-reinforced rubber for grease, oil, gasoline, and salt water resistance.
For Pipe OD | |||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|
| Inch | Metric | Lg. | Wd. | Thick. | Measuring Lg. | Front Graduation Marks (Numeric Increments) | Color | Graduation Color | Max. Temp. | Each | |
Rubber | |||||||||||
| 1"-6" | 2 mm-60 cm | 30" | 2 5/8" | 3/64" | 28" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 000000 |
| 2"-16" | 2 mm-78 cm | 60" | 3 7/8" | 3/64" | 36" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 00000 |
| 6"-30" | 2 mm-77 cm | 120" | 5 1/4" | 3/64" | 36" | 2 mm (1 cm), 16ths (1") | Gray | White | 360° F | 0000000 | 00000 |
Pipe Flange Aligners with Protractor
Line up two pipe flanges and determine pipe angle with the included nut-and-bolt pins, level, and protractor. Flange holes align as you tighten the pins.
| For Flange Hole Dia. | Angle Measuring Range | Graduation Marks (Numeric Increments) | For Distance Between Bolt Holes | Each | |
Aluminum | |||||
|---|---|---|---|---|---|
| 3/16"-1 3/4" | 0°-90° | 2.5° (2°) | 2"-5 1/2" | 0000000 | 0000000 |
Pipe Flange Aligner Pins with Horizontal Level
Ensure horizontal alignment of pipe flanges with a level rod that runs between two alignment pins. One pin in each pair has a level for vertical alignment. Insert these nut-and-bolt pins into adjacent flange holes and tighten to align flanges before connecting two pipes.
Pipe Flange Aligner Pins
Insert a pair of these nut-and-bolt pins into adjacent flange holes and tighten to align flanges before connecting two pipes. One pin in each pair has a level for vertical alignment. Use a separate level to align the flange horizontally.
Stepped Pipe Flange Aligner Pins
Each step on these aligner pins matches common bolt holes on pipe flanges, so they're more precise than conical aligner pins and don’t require nuts. Press the pair of pins into mated flanges to make sure the flanges are aligned. Once two sets of holes are aligned, you'll know the rest of the holes are as well. Made of durable chrome-plated steel, they'll hold their shape over time and resist rust.