Create a stand with interchangeable attachments for versatility.

With long, wide angled arms, this stand supports pipe up to 36" diameter. Leveling feet provide stability.

Optional V-wheels mount into the arms to make rotating material easy.

Cradle pipe and bar stock while machining. V-shape rollers provide smooth material feeding for long, thin objects.

Place stand on a work surface to position pipe perpendicular and parallel to the frame while machining.

Rollers support and help guide material into machinery.

Ball transfers allow movement in any direction so you can turn material without lifting it. Feet have mounting holes for floor mounting.

These U-shaped supports allow access to pipe and conduit after installation. Use them to suspend pipe, tube, and conduit above the floor. To install, add an extension pipe (not included) that is approximately 4" shorter than the desired height. Tack weld pipe to the base and support, then bolt the base to the floor. Fine-tune the overall height using the adjustment screw.

Galvanized steel supports have good corrosion resistance. 304 stainless steel supports have excellent corrosion resistance.

For technical drawings and 3-D models, click on a part number.

For a secure hold on pipe and conduit suspended above the ground, these supports have a cushioned clamp provides a 360° grip while reducing vibration. To install, add an extension pipe (not included) that is approximately 4" shorter than the desired height. Tack weld pipe to the base and support, then bolt the base to the floor. Fine-tune the overall height using the adjustment screw.

Galvanized steel supports have good corrosion resistance. 304 stainless steel supports have excellent corrosion resistance.

For technical drawings and 3-D models, click on a part number.

Reduce noise caused by HVAC systems. These sturdy rubber supports isolate vibration caused by heat pumps and air conditioning units, resulting in a quieter facility. When used on roofs, they also keep components above puddled water, which can cause damage. Supports have integrated strut channel that works with strut fittings and strut-mount routing clamps to organize and secure duct, pipe, tubing, and conduit.

Style A supports have a 1-5/8" wide strut channel for use with strut-mount clamps.

Style B supports have a roller that allows pipe and duct to move—good for HVAC systems where vibration is present.

Style C supports have two bases for additional stability and a 1-5/8" wide strut channel for use with strut-mount clamps.

Adjust supports to the exact height you need to route pipe, conduit, and tubing through strut-mount routing clamps and hangers. The wide base provides stability without needing to permanently secure to the floor. Supports have a 1-5/8" wide strut channel for use with strut-mount clamps and hangers.

Use supports with strut channel and loop hanger to suspend material such as pipe, tube, and conduit.

For technical drawings and 3-D models, click on a part number.

Bolt these supports directly to a pipe flange to suspend a run of pipe above the floor. Unlike clamps and hangers, which fasten to walls and ceilings, these supports mount to the ground. To install, add an extension pipe (not included) that is approximately 4" shorter than the desired height. Tack weld pipe to the base and support, then bolt the base to the floor. Fine-tune the overall height using the adjustment screw.

Galvanized steel supports have good corrosion resistance. 304 stainless steel supports have excellent corrosion resistance.

For technical drawings and 3-D models, click on a part number.

Clip these saddles around the outside of strut channel for a quick way to route insulated tubing and pipe. Curved edges on each end of the saddle protect insulation from abrasion if the pipe moves.

Set up the tripod wherever you need to hold pipe, tubing, and conduit for cutting and threading.

Chain-style vises have jaws on the base. Crank the handle to tighten the chain, securing the object against the jaws.

Yoke-style vises have top and bottom jaws—turn the handle to clamp the object between them. They have a hinged side opening with a locking latch. You can reverse the yoke to open on the left or right. Yoke style is not recommended for plastic pipe.