These ties have a loop on each end that can be twisted around each other for a secure closure.

Use in light duty applications such as tagging and attaching documentation to equipment.

Route pipe, tubing, and conduit across strut channel.

Organize multiple lines of pipe, tubing, or hose with a single clamp. They are polyethylene for good chemical and UV resistance.

For use on a single line, these polypropylene clamps withstand moisture and most chemicals. They're commonly used to route tubing in compressed air systems. A folding arm closes to secure material.

Backed with foam adhesive tape, these clamps mount to any smooth surface—no fasteners required. They are noncorrosive, nonconductive nylon.

Join these clamps together to line up multiple pipes, cables, or tubes side-by-side, even when they are different sizes.

Slide multiple clamps into existing strut channel to organize lines of pipe, tubing, and conduit without the need for drilling, welding, or using adhesive. Clamps have a plastic or rubber cushion or body to reduce vibration.

Secure two pressurized hydraulic lines with a single clamp to lessen vibration in hydraulic systems. Weld the bottom plate onto the mounting surface for a more secure connection than rail- and adhesive-mount clamps.

For use with a single line, these clamps mount directly onto rails, no adhesive or welding required. They fit tightly around pressurized lines in hydraulic systems to lessen vibration.

These hangers have a swivel nut for adjusting direction after mounting. They're also known as teardrop hangers. Combine with a threaded rod or other fastener to hang from the ceiling.

These plastic hangers prevent corrosion caused by metal-to-metal contact. Push them closed for a more secure hold on material than loop hangers.

These fiberglass-reinforced polyurethane U-bolts have no metal parts, so they won't conduct electricity or cause metal-to-metal corrosion.

These plastic rings won't conduct electricity. Also known as distribution rings, they have a large opening for routing multiple cables. A smooth surface prevents damage to wire and cable.

Lighter and safer than metal strapping, plastic strapping is also more flexible.

Slip these buckles onto strapping as you tighten.

These tensioners apply extreme tension on plastic strapping to hold it tight around packages. They hold the bottom strap and tension the top strap by winding it around a take-up wheel.

These kits come with plastic strapping and tools to secure it around packages.

These tools use heat to secure strapping without crimping on a seal.

Also known as crimpers, sealers secure seals onto plastic strapping to hold it tight.

This film has a corrosion inhibitor built-in to shield metal contents from corrosion.

No need for a separate dispenser—these rolls already have dispensing handles.

Protect sensitive items from static charges.

Also known as Type 3 slings, the eyes lie in a flat position for easy removal from beneath loads.

Also known as Type 5 and endless slings, these slings last longer than other web slings with eyes because they can be rotated to change the load-bearing point.

Also known as Type 4 slings, the eyes are turned 90° so they can form a choker configuration more easily than with flat-eye slings.

Also known as cargo slings, these wide slings provide extra stability and balance when lifting bulky loads.

Securely hook these slings to a load that has lifting eyes.

Slings have plastic-coated fibers woven into the edges for added abrasion resistance.

Also known as Type 5 and endless slings, these slings last longer than slings with eyes because they can be rotated to change the load-bearing point.

Suspend large and bulky items, such as coils of rope and step ladders. Wrap the strap around an item and then hook the buckle onto the mounting plate for a secure hold.

A quick-stop lanyard must be used when you have less than 18 1/2 ft. of fall clearance as it will stop your fall within a few inches.

Made of Kevlar, these lanyards meet ASTM F887 when used with an arc flash-resistant harness.

Keep your equipment close and prevent accidental drops.

Give your back the extra support it needs for lifting and other strenuous activities.

A combination of moisture and chemical resistance makes this hook and loop a good choice for most applications.

Each connector on this hook has two gripping heads for super-strong holding power.

Use the center hole to screw, nail, or rivet these discs to a surface.

The extra-strong adhesive on the back of this hook and loop sticks where others won't.

Cover surfaces up to 60" wide.

This hook and loop meets standards for flame retardance.

Cut to wrap around any size bundle.

Mushroom-shaped heads interlock for a secure hold when two pieces are pressed together.

When two parallel strips are pressed together, these fasteners are about one-third to one-half the thickness of other snap-together fasteners.