Regulate pressure in air and inert gas systems from your instrument panel—these valves have threads below the adjustment knob and come with a panel-mount nut.

Push-to-connect fittings form a low-pressure seal around plastic or soft metal tubing.

Compression fittings bite down on hard metal and plastic tubing for a tighter seal than push-to-connect fittings.

Less than a quarter of the height of standard pressure-relief valves, these are often installed on tanks in low-clearance areas.

With a three-port design, these valves allow inline flow from the inlet to the outlet during normal conditions and divert flow through the relief port in overpressure conditions. They are often used with feed pumps for fertilizers and bleach.

A lower profile than our other compressed air regulators makes these regulators a better fit in tight spots.

Mount these regulators to a 35 mm DIN rail with the included brackets.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

These filter/regulator combinations come as one convenient unit that cleans the air as it regulates pressure.

A filter and regulator joined top-to-bottom, these filter/regulators fit in the same space as a filter alone.

Assembled, inspected, and packaged in a clean environment, these filter/regulators come sealed in antistatic double bags.

Mount these filter/regulators to a 35 mm DIN rail with the included brackets.

An SMC filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Norgren filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A Parker filter, regulator, and lubricator are combined to provide clean, lubricated compressed air at your required pressure.

A filter, regulator, and lubricator with push-to-connect fittings are combined to provide clean, lubricated compressed air at your required pressure. Fittings make a tight seal around tubing.

With one outlet port before the lubricator and one after, these filter/regulator/lubricators work in systems that require lubrication in some lines but not in others.

Mount these valves directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. They control the speed of air-powered equipment by adjusting the volume of airflow.

A swiveling outlet port on these valves makes connections from any direction. They control the speed of air-powered equipment by adjusting the volume of airflow.

A numeric indicator provides a relative measure of airflow, similar to the volume dial on a speaker, so it's easy to set the same flow rate with each use. Mount them directly to cylinder ports, eliminating additional tubing between the cylinder and valve for better control than inline valves. They control the speed of air-powered equipment by adjusting the volume of airflow.

Prevent accidental airflow changes with these valves, which require an adjustment tool to alter their flow rate. They control the speed of air-powered equipment by adjusting the volume of airflow.

Designed to be mounted inline, these valves can be placed in easy-to-reach locations. Made of plastic and stainless steel parts, they have excellent corrosion resistance. They control the speed of air-powered equipment by adjusting the volume of airflow.

Made of PBT, these plastic valves are more corrosion resistant than valves made of aluminum or nylon. A single dial adjusts airflow equally in both directions, controlling the extension and retraction speed of an air cylinder at the same time.

With two 2-way integrated solenoid valves, these electrically controlled valves direct airflow to venturi pumps, which generate the suction you need to run end-of-arm tools, such as vacuum cups.

With two 3-way integrated solenoid valves, these electrically controlled valves direct airflow to end-of-arm tools that don’t require vacuum suction, such as pick-and-place grippers. Also known as 3/2 valves, each of the two solenoid valves directs air to a different port.

A muffler reduces exhaust noise. Valves allow airflow into your equipment and then quickly dump exhaust air to the atmosphere without routing it back through a directional control valve to speed up the movement of equipment. Also known as quick exhaust valves.

These valves have union fittings that disassemble for fast installation and removal from pipelines. Use with water, air, and inert gas.

Use these valves with garden hose and other landscaping equipment. They’re for use with water, air, and inert gas.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, oil, air, and inert gas.

Use these plastic valves for a lightweight and economical alternative to metal. They have a compression sleeve that bites into tubing as you tighten the nut, forming a strong seal. Use with water, air, and inert gas.

With a fluoroelastomer seal and a CPVC body, these valves can withstand aggressive and corrosive solutions in chemical-processing applications.

For fast installation and removal from pipelines, these valves have union fittings that disassemble into multiple pieces. All have a fluoroelastomer seal and a plastic body that can stand up to aggressive and corrosive solutions in chemical-processing applications.

The three-piece bolted body comes apart for access to internal components without unthreading pipe connections and removing the valve from your line. Seal is fluoroelastomer and body is polypropylene for excellent resistance to aggressive and corrosive solutions in chemical-processing applications.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves have a fluoroelastomer seal and a plastic body that can withstand aggressive and corrosive solutions in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. To withstand aggressive and corrosive solutions, they have a chemical-resistant fluoroelastomer seal and a plastic body.

Insert unthreaded pipe into the socket ends and bond with primer and cement to create a permanent, leak-tight connection. These valves meet NSF/ANSI Standard 61, which means they’re safe to use with drinking water systems.

These valves meet NSF/ANSI 61 for use in drinking water lines.

Insert tubing into the push-to-connect fittings on these valves—no heat, solder, or flux required. They meet NSF/ANSI 51 for safe use with food.

These valves have NPT connections for use with threaded pipe.

For use with threaded pipe, these valves have NPT connections.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

Safe for automated on/off control in drinking-water systems, these valves meet NSF/ANSI Standard 61.

Insert tubing into the fittings on these valves—no heat, solder, or flux required.

A compact, lightweight actuator and an angular body allow you to install these valves in any mounting orientation.

Also known as actuated ball valves, these provide higher flow rates than other air-driven valves.

Insert unthreaded pipe into the socket ends and bond with PVC primer and cement to create a permanent, leak-tight connection.

To ensure consistent and repeatable settings, these valves have color-coded handle threads and numerical markings. One full revolution of the handle reveals a new color to indicate the set point. Use these valves with water, oil, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They’re for use with water, air, and inert gas. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Use these valves with NPT threaded pipe. They have a fluoroelastomer seal and a plastic body to withstand aggressive and corrosive solutions in chemical-processing applications. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

Barbs grip onto tubing, providing a secure hold. To withstand aggressive and corrosive solutions in chemical-processing applications, these valves have a PTFE seal and a PVDF body. Turn the handle to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

These valves have barbed fittings that grip onto tubing, providing a secure hold. They’re often used in food and beverage tubing lines to adjust flow in small increments for metering, sampling, and other applications requiring fine flow control.

For lightweight and corrosion-resistant alternative to metal, these valves are plastic. Attach garden hose to the valve outlet. Use with water. These valves gradually open and close to adjust and regulate flow.

Often used in low-pressure water pipelines, these valves have a plastic body for the lightest weight of our flanged flow-adjustment valves. Use them with water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

These valves meet NSF/ANSI 61 for use with drinking water. They bolt to flanges to adjust and regulate flow in flanged pipelines.

For a lightweight alternative to metal valves, these have a plastic body. To fit in tight spots, they have a low-profile handle and a short end-to-end length. Valves are for use with water, oil, air, and inert gas. All divert flow between ports.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. All are for use with water, oil, air, and inert gas. They divert flow between ports in tubing lines.

For easy installation and removal from pipelines, all ends on these valves have union fittings that disassemble into multiple pieces. Their fluoroelastomer seal and plastic body can withstand aggressive and corrosive solutions for diverting flow between ports in chemical-processing applications.

Perform valve maintenance without unthreading pipe connections. These valves have a three-piece bolted body that comes apart for inline access to internal components. The fluoroelastomer seal and glass-filled polypropylene body can withstand aggressive and corrosive solutions for diverting flow in chemical-processing applications.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. Designed for diverting flow between ports in chemical tubing lines, they have a fluoroelastomer seal and a PVDF body to withstand aggressive and corrosive solutions.

Insert tubing into the fittings on these valves—no heat, solder, or flux required. They divert flow between ports in food and beverage tubing lines.

To test water quality without interrupting flow, drain a small amount of liquid through the sampling outlet.

Connect these orifices to threaded pipe, or insert them into threaded holes.

Push tubing into these orifices, and an internal ring holds them in place. They're for use with plastic and soft metal tubing.

These switches have a low-profile design to fit in water pipelines with limited clearance.

For installation in instrument panels, these flowmeters have fittings on the back.

Use these flowmeters for highly accurate flow rate measurements.

Measure the flow rate of water in both gallons and liters.

Calibrated, cleaned, and bagged for oxygen service, these flowmeters are commonly used for welding.

Bond the unthreaded connections to PVC pipe with PVC cement and primer.

Determine the flow rate and total flow volume of water with the same meter.

Made of acetal, these couplings are lighter in weight than metal quick-disconnect couplings. Compatible with Plastic-shape plugs and sockets.