Once aftercoolers and separators have removed the bulk of the water, use these dryers to remove any remaining moisture in your air line.

Get dry compressed air in high-pressure systems—these dryers have a maximum pressure rating of 300 psi. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

These dryer/filters have a clay desiccant that removes moisture, oil, and particles, so there’s no need to install a separate filter and dryer. Once aftercoolers and separators have removed the bulk of the water, they remove any remaining moisture in your air line.

Each of these filter/dryers has two desiccant towers—one that absorbs moisture, particles, and oil in the air while the other reactivates saturated desiccant so you have an uninterrupted supply of clean, dry compressed air.

These all-in-one dryer/filters eliminate the need for individual dryers, separators, and filters. They cool air through refrigeration to condense water vapor for removal.

A float-operated drain valve on these separators automatically opens when the bowl begins to fill. The first step in water removal, use one of these separators to remove the large amount of water as compressed air cools.

In addition to removing large amounts of water, these separators also remove particles and oil droplets. Place them after your compressor and aftercooler, or at the point of use in applications that don't require an aftercooler.

Also known as regenerative blowers, use these to produce high-flow compressed air with low pressure or vacuum to operate pump drives, lift tables, and conveying systems.

Create a high-flow air stream from your compressed air supply. Flow boosters draw in ambient air, which amplifies compressed air flow.

These blowguns have a metal body.

The rubber tip won't damage parts.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.

Connect the included hose to your air supply and these blowguns are ready to use.

The included hose is ready to connect to your air supply.

These guns include a rubber tip that won't damage your workpiece.

Designed to reduce noise, these blowguns are quieter than similar standard guns.

Maximize comfort and minimize strain with these lightweight guns.

The extra length lets you access hard-to-reach areas.

The flat nozzle distributes air over a wide area.

Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.

These tubular holders have open ends. Slide a blowgun inside for storage.

Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.

These guns provide more than three times the airflow of standard static-eliminating blowguns.

Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.

Attach to your blowgun to direct airflow.

Extend these telescoping nozzles to increase your reach.

The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.

Nozzles are attached to a flexible tube or hose that bends and holds its shape until you reposition it.

The magnetic base mounts to your work surface and has a control valve for adjusting airflow.

Secure an air knife to the bracket and position where needed. Two swiveling joints allow 360° movement.

Use one bracket for 3" to 18" wide air knives; two brackets for 24" to 42" wide air knives, and three brackets for 48" wide air knives.

Also known as air wipes, these use a 360° airstream to blow off, dry, clean, and cool tubes, cables, extruded shapes, and hoses.

Attach to a blower for high-speed airflow at low pressure.

Blast your heating, drying, and shrinking projects with hot air to get the job done quickly. Choose from blowers with temperature settings from 300° to 750° F.

Replace filters or add parts baskets and drum dollies to your parts cleaning vacuum/blowers. All of these filters and accessories can be used with compatible MiJET parts cleaners.