We will reply to your message within an hour.
Internal mounting bosses enable you to attach panels or DIN rail inside the enclosures using self-tapping screws. Made of polycarbonate, these nonconductive enclosures resist denting, chipping, and cracking.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components. Enclosures are made of nonconductive polycarbonate that resists denting, chipping, and cracking.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components. These enclosures have a clear cover, so you can inspect components without opening the enclosure.
Made of polycarbonate, these enclosures resist denting, chipping, and cracking.
Mounting feet make attachment to machines and walls hassle-free. These enclosures are small and lightweight for use with sensors, switches, testing devices, and circuit boards.
View all sides of your installed components.
Control access to these enclosures with a key-operated lock.
Mounting feet make attachment to machines and walls hassle-free.
Made of polycarbonate, these enclosures resist denting, chipping, and cracking better than stainless steel enclosures.
Made of nonconductive polycarbonate, these enclosures withstand prolonged submersion in water while protecting electronics from dents, chips, and cracks.
Internal mounting bosses or mounting brackets enable you to use panels or DIN rail to mount components.
Fasten these enclosures to machine control panels or walls without exposing the contents to wet and oily environments.
Install these enclosures on control panels and walls and inspect what’s inside without exposing their contents in wet and outdoor locations.
Made of nonconductive polycarbonate, these enclosures withstand prolonged submersion in water while protecting electronics from dents, chips, and cracks. A clear cover lets you monitor the inside without opening them.
Inspect components without opening the cover.
Check on the contents inside these enclosures from every angle without opening them in wet environments.
Mount these enclosures directly to machine control panels in wet environments and view the contents without opening them.
Two separate chambers allow you to access wiring connections in the lower section without disturbing components that you install in the upper section.
Suitable for installing in the ground or for use in wet environments, these direct burial enclosures are rated NEMA 6P for protection from dirt, washdowns, corrosion, and water submersion.
Often used to house emergency-stop buttons, switches, and lights, these bright yellow enclosures are easy to spot, even in dimly lit areas. All have standard-size push-button holes to save time—no need to measure and cut your own holes.
House emergency stop buttons, life safety equipment, and other devices that need to be seen with these brightly colored enclosures, which are easy to spot even in high-dust areas.
Protect keypads, push-buttons, and other handheld controls with these round enclosures that are more comfortable to hold than square enclosures.
Create battery-powered, hand-held devices such as card and signal readers—these enclosures have a clear cover for checking screens and status lights inside.
These enclosures shield electrical components from water, so they’re safe to install onto DIN rail in wet and washdown environments.
Protect monitors and televisions from environmental damage with these enclosures.
Monitor HMI covers make it easy to access HMI devices, push-buttons, and other electronics mounted on the exterior of an enclosure through a clear window without opening the cover.
Easily access HMI devices, push-buttons, and other electronics mounted on the exterior of an enclosure while keeping contents safe from water, oil, dust, and weather.
Add panels to T-slotted framing to create machine guards and strip doors.
Save time when wiring connections in a junction box; these blocks come already installed in an enclosure.
Inspect the terminal block and wiring without opening the cover.
Compact in size, these guards can be mounted directly to a machine or workbench. Panels are framed in aluminum T-slotted extrusions to provide multiple points of attachment for other components.
Framed in aluminum T-slotted extrusions, these customizable machine guards provide multiple points of attachment for other components and structures.
Combine posts, panels, and doors to create a barrier around equipment.
Pair these hoods with an exhaust system to contain harmful fumes, vapors, and gasses while venting them away from work spaces—they protect users from inhaling or coming in contact with them.