Body Material Body Material |
---|
|
Fitting Material Fitting Material |
---|
|
Filter Material Filter Material |
---|
|
Maximum Flow Rate Maximum Flow Rate |
---|
|
Removes Particle Size Down To Removes ParticleSize Down To |
---|
|
These breather vents withstand corrosion in damp environments. Use them to prevent excess vacuum and pressure in cylinders, gear boxes, and tanks and to block debris from entering equipment.
Polyethylene breather vents can be cleaned with mineral spirits.
For technical drawings and 3-D models, click on a part number.
Pipe Size | Max. Flow Rate | Max. Pressure, psi | Max. Temp., °F | Ht. | Dia. | For Use With | Removes Particle Size Down To, microns | Each | |
NPT Male | |||||||||
---|---|---|---|---|---|---|---|---|---|
Polyethylene Plastic Body and Fitting | |||||||||
1/8 | 1 scfm @ 100 psi | 100 | 150° | 7/16" | 1/2" | Air, Inert Gas | 100 | 0000000 | 00000 |
1/4 | 3 scfm @ 100 psi | 100 | 150° | 1/2" | 11/16" | Air, Inert Gas | 100 | 0000000 | 0000 |
3/8 | 9 scfm @ 100 psi | 100 | 150° | 11/16" | 15/16" | Air, Inert Gas | 100 | 0000000 | 0000 |
1/2 | 10 scfm @ 100 psi | 100 | 150° | 11/16" | 15/16" | Air, Inert Gas | 100 | 0000000 | 0000 |
3/4 | 20 scfm @ 100 psi | 100 | 150° | 1 1/8" | 1 1/2" | Air, Inert Gas | 100 | 0000000 | 0000 |
1 | 22 scfm @ 100 psi | 100 | 150° | 1 3/8" | 1 7/8" | Air, Inert Gas | 100 | 0000000 | 0000 |
Keep moisture, dirt, and debris from entering your oil reservoirs. The silica gel inside these breather vents absorbs moisture from the air, preventing rust from forming inside your tanks. The gel changes from blue to pink as it becomes saturated, letting you know it needs to be replaced. A second filter blocks dust and other particles from getting inside. These breather vents allow air to flow in and out of your lubrication system, keeping excess vacuum or pressure from building up in cylinders, gear boxes, and tanks.
Breather vents with a plastic body are clear, so a quick glance will tell you if the gel is saturated. Unlike steel versions, which can be rebuilt, the entire unit must be replaced when fresh gel is needed.
For technical drawings and 3-D models, click on a part number.
Pipe Size | For Tank Capacity, gal. | Max. Flow Rate | Max. Temp., °F | Ht. | Dia. | For Use With | Removes Particle Size Down To, microns | Each | |
Nylon and Polycarbonate Plastic Body and Nylon Plastic Fitting | |||||||||
---|---|---|---|---|---|---|---|---|---|
1 | 5-200 | 16 scfm @ 1 psi | 200° | 6 1/8" | 4 1/8" | Air, Inert Gas | 3 | 0000000 | 000000 |
1 | 5-350 | 16 scfm @ 1 psi | 200° | 8 1/8" | 4 1/8" | Air, Inert Gas | 3 | 0000000 | 00000 |
1 | 5-500 | 16 scfm @ 1 psi | 200° | 10 1/8" | 4 1/8" | Air, Inert Gas | 3 | 0000000 | 000000 |