Made from polypropylene, these batch tanks handle temperatures up to 220° F that would warp standard plastic containers. A seamless one-piece construction eliminates joints where contents can leak or residue can collect. The semi-clear body lets you check fill levels without removing the lid. A loose-fitting lid allows venting during heated processes while keeping out debris. All sizes stack when empty to reduce your storage footprint.

These dispensers have a reservoir for recirculating coolant. They provide a constant flow of coolant, so they dissipate heat more efficiently than mist and droplet dispensers, making them suitable for cooling long machine cycles. Coolant strainers prevent debris from getting into the recirculated coolant.

Maximum flow rate and shut-off height are for water-soluble oil.

Prevent drain blockage—these traps have a reusable basket to catch debris, such as metal chips and stones, before it enters your sewage system. For quick disposal, unthread the thumb screws by hand to access and remove the reusable basket. When the tank is closed, a gasket seals in odors.

Install these traps under your sink as a P-trap replacement. The tank and basket are made of polypropylene, so they resist acids and other chemicals.

Quickly set up a line to dispense chemicals—these nozzles come with a hose and fittings that thread onto your drum or intermediate bulk container (IBC). The nozzles are made of either polypropylene or aluminum and the hose is PVC to resist corroding from citric acid, ethanol, and other chemicals. However, the nozzles are not designed for pressurized systems and should be used in applications where liquid can flow by gravity. Use the trigger to adjust how much they dispense at a time. The nozzles swivel to make directing the flow easier. Hook the included bracket onto the top of a drum or tank to hang the hose when not in use.

Connect these washers to a water supply to rinse many pipettes efficiently, reliably, and safely. Place pipettes within the carrying basket, which cushions them to prevent breakage. After soaking them, transfer the basket to the rinser. The rinser fills with clean water to wash your pipettes and rapidly siphons out contaminated water to maintain cleanliness. All components are made of polyethylene or polypropylene to withstand common cleaning solutions.

Small enough to spray with one hand, these foamers aerate cleaners to create a foam that breaks down dirt and grime. The foam is easier to see than liquid cleaners and clings where liquid cleaners might drip. They can also be used as sprayers. Swap out the included nozzles as needed—go from a fine mist for delicate surfaces to a powerful stream to remove stuck-on material.

Lubricate your track to reduce friction and wear without shutting down equipment. Oil-infused resin distributes lubricant onto rollers, which transfer it to your track. For proper lubrication, your roller needs to make at least one full rotation.

Designed to cool short and intermittent machine cycles, misting dispensers dissipate heat more efficiently than droplet dispensers, while using considerably less fluid than flood dispensers.

Pump the handle to pressurize the tank, then squeeze the trigger on the wand to spray. These sprayers are often used for degreasers, insecticides, disinfectants, cleaning solutions, and herbicides.

Note: The material of the parts can affect a sprayer's compatibility with a chemical or solution. Make sure the tank, seal, wand, and nozzle are suitable for your application.

Crank the handle on the built-in hand jack to position cylinders up to 11" off the ground for easier loading. A tightening handle puts tension on the chain to secure the cylinder. Rear legs with swivel casters provide additional stability and mobility.

Small and lightweight enough to hold with one hand or wear in a holster. These sprayers have a plastic tank that resists chemicals. Use them with degreasers, insecticides, disinfectants, cleaning solutions, and herbicides.

Note: The material of the parts can affect a sprayer's compatibility with a chemical or solution. Make sure the tank, seal, nozzle, and pump are suitable for your application.

Carry this sprayer comfortably on your back using the padded shoulder straps. Pump the handle to pressurize the tank, then squeeze the trigger on the wand to spray degreasers, insecticides, disinfectants, cleaning solutions, and herbicides.

Note: The material of the parts can affect a sprayer's compatibility with a chemical or solution. Make sure the tank, seal, wand, and nozzle are suitable for your application.

Replacement Trigger and Wand Kits—Replacement trigger and wand kits include a chrome-plated steel wand. Kit does not include nozzles.