Complete with a suction strainer and 6 feet of garden hose, this little pump comes ready to clean up small open spaces. It activates when you plug it in. Use with debris-free water.

Maintenance kits (sold separately) include an impeller, an O-ring, and a seal.

Note: The pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least 3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least 3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Also known as bilge pumps, these remove fresh and salt water from spots where other pumps don’t fit. They have an internal sensor, so they turn on when they detect water and turn off when the water is removed. Pumps are fully submersible. They are gravity fed and require an elevated liquid source to fully fill the pump before turning on.

Pumps for 12 volts DC work with 12-volt batteries.

Pumps for 120 volts AC are for use in debris-free water.

Convenient to keep in your toolkit for on-site cleanup, these pumps attach to your drill for small liquid extraction jobs, as well as draining water from clogged sinks and emptying tanks. Pumps are self-priming, which means they create a suction force to draw liquid upward. Do not use with solids.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2" in diameter. Pumps are self-priming, which means they create a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. All have a pull-start engine. They are not submersible. These pumps cannot be sold to Canada due to import regulations.

Pump with a tank capacity of 1.6 gallons includes an electric starter that operates on a 12-volt battery (sold separately). It cannot be sold outside the United States because of energy efficiency requirements.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

These pumps weigh only 16 pounds and have a handle, so they're convenient for on-site sampling, atomizing, and vacuum filtration. They're also for use in pressure applications up to 60 psi. Since they don't require lubrication, there’s no risk of oil contamination. Maximum flow rate is the rate at which air is pumped before a vacuum is created. Flow rate steadily decreases as the pump generates the vacuum. The larger the tank, the longer it will take to form a vacuum. Tube and fitting ID will also affect flow.

Repair kits include filter/muffler components, a gasket, a leaf valve, limiters, and an O-ring.

For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

A nozzle and hose allow you to dispense directly into your container. For on-site diesel fuel dispensing at construction sites, on boats, and in other environments without electrical hookups, attach these portable pumps to any 12-volt battery.

Pump with vehicle plug connects to a 12-volt vehicle outlet. Pump with spring clamps connects directly to a 12-volt vehicle battery.

Compressors turn on when the tank falls to the actuation pressure and they turn off when the tank reaches the maximum pressure.

Compressors that cannot be sold to the listed areas are restricted due to product regulations.

Get compressed air from a DC power source—these compressors can run on a 12-volt vehicle battery (not included) for use on trucks and heavy equipment, or a DC generator. Use them to inflate tires, clean filters, and operate light-duty tools, such as nailers, hammers, and small impact wrenches. For best results with a vehicle battery, use a deep-cycle, large-cell battery rated for continuous use.

Connector assemblies come with a three-foot hose and a connector that can be fixed to a panel or frame for operating compressors installed in difficult-to-reach locations, such as under a vehicle.