These pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least _3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Complete with a suction strainer and 6 feet of garden hose, this little pump comes ready to clean up small open spaces. It activates when you plug it in. Use with debris-free water.

Note: The pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

Clean up water in flooded areas without a sump pit. Install these pumps in debris-free water that’s at least 2" deep. They activate when plugged in. You can add a plug-in switch to control when the pump activates. Submerge while in use.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Pumps have a powerful motor that provides more than twice the flow rate of standard dewatering pumps to quickly remove large volumes of liquid. They activate when plugged in; add a float switch to control when the pump activates. A top-discharge design routes water through the pump to cool the motor. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before during on. Do not run dry.

Transfer raw sewage water that contains solids up to 2” in diameter. These pumps have a float switch with a separate cord that can unplug, so you can replace the switch without replacing the whole pump. The length of the float switch cord is adjustable. Turn-on and turn-off levels will vary according to the length of the cord. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Use this pump to remove water with small solids up to _1/4" in diameter. It activates when plugged in; add a plug-in switch to control when the pump activates. Install in water that's at least 2" deep. Pump includes a 25-ft. hose with cam and groove fittings for quick, secure connections and a storage crate with built-in filtration to protect the pump from debris.

Note: Pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

This pump has a totally enclosed nonventilated (TENV) motor that is cooled by the liquid being pumped. Also known as a flexible impeller pump, it creates a suction force that can draw liquid upward to fill the pump chamber when your liquid source is below the pump. Mount up to 6 feet above your liquid source. Pump can pass solids up to _1/4" in diameter without clogging, so there’s no need to filter sediment and debris. A handle makes it convenient for on-the-go removal of bilge water, waste oil, and spills. Pump can also be used to cool marine engines and drain liquid from holding tanks.

Note: Pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

The switch activates on increasing pressure caused by rising water levels for a long service life. It has a separate cord, so you can replace the switch without replacing the whole pump. Use the handle to carry pumps from job to job. Install in debris-free water that’s at least _3/4" deep. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Fill the fuel tank with gasoline to remove water at sites without power. These pumps are self-priming, which means they create a suction force to draw liquid upward and fill the pump chamber. They can be mounted up to 20 feet above your liquid source. All have a pull-start engine. Pumps are not submersible.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Remove water in locations without power with these battery-powered pumps. They attach to an 18-volt battery.

Note: The pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

An aluminum housing provides excellent impact resistance. Use these pumps to clean up water in flooded areas without a sump pit. Install them in debris-free water that’s at least 2” deep. Pumps activate when plugged in. You can add a plug-in switch to control when the pump activates. Submerge while in use.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

Built with high-chromium stainless steel components, this pump stands up to salt water with up to 25% sand by volume and resists wear caused by abrasive particles. Fill the fuel tank with gasoline to remove water at sites without power. Pump is self-priming, which means it creates a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. Pump has a pull-start engine. It is not submersible.

Note: Pump must be filled with liquid before use. It needs a constant flow of liquid and cannot run dry.

This pump has an impact-resistant aluminum housing and handles larger solids than other battery-powered dewatering pumps. Attach it to a 12-volt battery to remove water in locations without power. Pump is gravity fed and requires an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Install these pumps right in your line and engage the lever handle to start pumping. They have few moving parts that can fail for an extended service life. Pumps are gravity fed and require an elevated liquid source to fully fill the pump before turning on. Do not run dry.

Wheel these pumps to remote areas with no power. They can handle sewage water with thick sludge, silt, and debris up to 2" in diameter. Pumps are self-priming, which means they create a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. All have a pull-start engine. They are not submersible.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.

With a polypropylene housing, these pumps are about half the weight of other gasoline-powered pumps. Fill the fuel tank with gasoline to remove water at sites without power. Pumps are self-priming, which means that they create a suction force to draw liquid upward and fill the pump chamber. Mount up to 20 feet above your liquid source. They have a pull-start engine.

Note: Pumps must be filled with liquid before use. They need a constant flow of liquid and cannot run dry.