We will reply to your message within an hour.
These blowguns have a metal body.
The lightweight plastic construction makes these blowguns more comfortable to hold than metal.
Compact enough to carry with you, these guns have a built-in quick-disconnect hose coupling for easy connection to an air line.
The rubber tip won't damage parts.
Designed to reduce noise, these blowguns are quieter than similar standard guns.
Also known as air-shield and safety-shield blowguns, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Two inlets allow connection to air lines above or below. Use the top inlet when the blowgun is suspended from an overhead hose and the bottom inlet for bench and floor hoses.
Connect the included hose to your air supply and these blowguns are ready to use.
Operate a blowgun without disconnecting your air tool—these guns fit between the tool and air hose. Good for blowing away debris after using an air-powered sander or grinder.
These guns include a rubber tip that won't damage your workpiece.
The extra length lets you access hard-to-reach areas.
The included hose is ready to connect to your air supply.
The lightweight plastic body is more comfortable to hold than metal.
Also known as air-shield and safety-shield blowguns, an outer air curtain deflects flying chips and dust while the center airstream blows away debris.
Increase your reach with the telescoping nozzle.
Maximize comfort and minimize strain with these lightweight guns.
These blowguns provide more than two times the airflow of standard guns.
The flat nozzle distributes air over a wide area.
The most powerful blowguns we sell, these use compressed air to clean and blow debris.
Clear dust and debris, test air ducts for leaks, and dry large surfaces without needing a compressed air line.
Blow air backward from the nozzle to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
Air flows out of the side of the nozzle to clean air filters, radiators, and inside recesses.
Also known as siphon guns, these spray air and liquids at the same time. Push the lever and the airflow creates suction that draws water, cleaning solution, or other liquids through the hose.
Clean surfaces without transferring dust or moisture from the air hose. These blowguns have a replaceable filter that traps particles such as rust and smoke and absorbs moisture.
A nonconductive plastic nozzle and tip protect against accidental contact with live electrical circuits. These blowguns are tested to 1,000 volts to meet IEC 60900.
Safely blow dust and debris off your clothes. These blowers are a safer alternative to compressed air and help you meet OSHA regulations.
Bend the stand's flexible arm to position your gun and keep it in place. Use the included foot pedal to activate airflow and static elimination.
These guns provide more than three times the airflow of standard static-eliminating blowguns.
Blow off dust and contamination, eliminate static charges, and guard against ESD (electrostatic discharge).
Made from rubber, these nozzles won’t scratch or damage sensitive workpieces.
Attach to your blowgun to direct airflow.
Also known as air-shield and safety-shield nozzles, a center airstream blows away debris while an outer air curtain deflects flying chips and dust.
Control consumption and noise by adjusting the airflow.
These premium nozzles are engineered for the most efficient airflow consumption.
The extra length allows access into hard-to-reach areas.
Extend these telescoping nozzles to increase your reach.
These needle-style nozzles force air to a precise pinpoint.
Focus air with pinpoint precision.
These nozzles are made of FDA-listed materials.
The flat nozzle tip distributes air over a wider area than focused-airflow nozzles.
At less than 2" long and with a wide airflow pattern, these nozzles are ideal for tight spaces where you need to distribute air over a wider area than a focused-airflow nozzle.
Air blows out of these flat nozzles in a wide pattern at a 90° angle from the inlet, distributing air over a wider area than focused-airflow nozzles. They’re FDA compliant 21 CFR 110.40 for use in the food industry.
Air blows out of these nozzles at a right angle in a wide pattern, distributing air over a wider area than focused-airflow nozzles.
Adjust airflow to control consumption and noise.
Blow air backward to clean out the inside of pipes, tubes, and channels without pushing debris into your system.
As compressed air flows through these nozzles, they rotate to efficiently and evenly blow off large areas.
Nozzles are attached to a flexible hose that bends and holds its shape until you reposition it.
Choose a base, hose, and nozzle for a custom setup.
The magnetic base mounts to your work surface and has a control valve for adjusting airflow.
Convert your blowgun to a spray gun. These nozzles spray air and liquids at the same time.
Attach one of these swivels to an air nozzle to direct air 30° left, right, up, and down.
Shaped to fit into extremely tight spaces, these nozzles can be used to remove parts from molds. Tap the wedge into position, attach the nozzle to a blowgun, and activate the airflow to release the part.
Often used for simultaneously spot cooling and blowing parts, these nozzles cool compressed air without electricity or refrigerants.
Turn your blowgun into a scraper to remove and blow away debris at the same time.
Launch foam cylinders through hose and tubing to power away dirt and deposits. Unlike cleaners with brushes, these work on flexible, curved, and coiled tubing as well as those with fittings, valves, and 90° bends.
Replace blower wheels, cords, handles, and other components on heat guns.
Insert plastic welding rod through a second opening in the nozzle. It directs air to heat the rod and weld plastic.
A deflector protects adjacent areas from heating. The flat shape creates a wide airflow.
Sets include a focused nozzle for concentrated airflow, a flat-tip nozzle for heating wide surfaces, and a deflecting nozzle that protects adjacent surfaces from heating.
Concentrate a heat gun's airflow.
Create a wide airflow that’s good for drying and stripping paint.
Shaped to hold round objects, use these nozzles for installing heat-shrink tubing and bending plastic pipe.
Prevent accidental contact with hot nozzles.
Set up your heat gun for hands-free operation.
Prevent buildup of electrostatic discharge (ESD) that can damage electronic components.
Sets include a focused nozzle for concentrated airflow, a flat nozzle for heating wide surfaces, and a curved nozzle for installing heat-shrink tubing.
Choose these guns for occasional heating.
Save up to four temperature and airflow settings.
Produce a concentrated flame for small objects.
Distribute heat over a wide area for large jobs.
Combine high-volume airflow with low-heat output for warming and drying.
Blast your heating, drying, and shrinking projects with hot air to get the job done quickly. Choose from blowers with temperature settings from 300° to 750° F.
Use these blowers for production drying, heat shrinking, and other applications requiring heat over 1000°F.
Replace filters or add parts baskets and drum dollies to your parts cleaning vacuum/blowers. All of these filters and accessories can be used with compatible MiJET parts cleaners.
Clean parts with compressed air without propelling fluids and debris all over your shop. These vacuum/blowers quickly blow coolant, oil, and chips off your parts while a vacuum sucks them into a removable drum for recycling or disposing of them.
Remove worn fittings and repair threaded holes.
Replace individual parts in a variety of Superior Pneumatic air-powered hammers.
Rivet setters are required for standard and heavy duty air-powered hammers to drive rivets.
Place against the back side of your rivet while hammering the head.
Also known as zip guns, use these air hammers with a rivet setter and a bucking bar to install solid rivets.
Kits include a hammer and round rivet setters.
Also known as alligator squeezers, these tools offer up to 6,000 lbs. of force to set solid rivets.
Add a straw to an aerosol can for precise applications or replace a lost or clogged straw.
Replace individual parts in a variety of blind rivet tools.
An extra-long nosepiece allows access to hard-to-reach areas.
Designed for durability, these tools can handle the demands of high-volume production and assembly.
Use these tools for repair and maintenance work.
These tools pull the rivet bolt tight to the collar, clinches the collar in place, and clips any excess length of the bolt.
Compressed air does the work for you.
These staplers compress the box material as the staple is driven for a tight clinch.
Drive bigger staples than you can with standard air-powered staplers.
Also known as bottomers, these staplers secure the bottoms of boxes.
These staplers have a smaller body and are 50% lighter than our other air-powered staplers.
To precisely set staples, these staplers have adjustable settings that control the tightness of the staple clinch and the depth of the staple, which prevents the staple from coming into contact with the box contents.
For less frequent reloading and increased productivity, these staplers hold nearly ten times more staples than standard air-powered box staplers.
Built for durability, these high-performance tools handle the demands of high-volume production and tough maintenance applications.
Use these tools for general shop applications.
These tools are suitable for general shop, maintenance, and automotive work.
Built for durability, these wrenches handle the demands of high-volume production and tough maintenance applications.
Use these wrenches for medium-volume production, general maintenance, and construction applications.
For accurate paint control without finger fatigue, snap these reusable adapters onto your aerosol cans.
Let compressed air do the work for you when dispensing sealants from cartridges.
Adjust air-flow for precise control and smooth material flow—these guns have a built-in pressure regulator with a control knob.
Vortex tubes convert compressed air into a stream of cold air.
Kits include one vortex tube for converting compressed air into a stream of cold air as well as airflow adjusters, a cold-air muffler, a tube fitting, and tubing.
UL classified for hazardous locations, these vortex tubes convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.
Keep electronics inside enclosures from overheating by converting compressed air into a stream of cold air.
These NEMA-rated vortex tube are designed to keep water out during washdowns.
Quietly cool electronics inside enclosures while keeping out rain, snow, splashing water, and dirt.
Set the thermostat and these vortex tubes switch on only when needed.
Often used in low-noise environments such as labs and clean rooms, these are quieter than standard enclosure-cooling vortex tubes.
Cool electronics inside enclosures while keeping out rain, snow, splashing water, and dirt.
Cool electronics inside enclosures to your desired temperature while keeping out rain, snow, splashing water, and dirt.
In addition to being quieter than standard enclosure-cooling vortex tubes, these stand up to washdowns and weather. They convert compressed air into a stream of cold air to keep electronics within enclosures from overheating while also keeping dust and other contaminants out.
Quietly cool electronics inside enclosures to your desired temperature while keeping out rain, snow, splashing water, and dirt.
Use these guns to clean as well as apply chemicals and solvents.
The powerful combination of air and water creates a high-velocity, atomized spray without needing high pressure. These guns also can be used to siphon.
Convert dispensing tips with male threads into quick-disconnect couplings.
Sets include dispensing tips for grease fittings and bare lubrication points.
Dispense from grease guns into grease fittings and bare lubrication points.
Lubricate standard grease fittings in hard-to-reach areas. Extensions have a quick-disconnect fitting that snaps into your dispensing tip for standard grease fittings.
These flexible extensions have a quick-disconnect fitting that snaps into your dispensing tip, so you can lubricate grease fittings that are hard to reach.
With threads on both ends, these rigid nozzles connect grease guns to dispensing tips.
These rigid tip adapters penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.
Penetrate gaskets, sealed bearings, and joints to deliver grease to precise locations.
These flexible nozzles have threads on both ends for connecting a grease gun to a dispensing tip.
Slide the metal sleeve up to the tip for rigidity. Slide it back down to expose the flexible nozzle.
These rigid nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.
These flexible nozzles come with a dispensing tip and have threads on one end for connecting to a grease gun.
Replace messy mist coolant dispensers—these convert compressed air into a stream of cold air. They can be used in applications where liquid coolant can't.
Use compressed air to dispense grease.
Choose from a variety of screwdriver, flat, conical, chisel, bevel, needle, and knife tips.